Zavedení
This manual provides essential information for the safe and effective use of your E-flite EFLA1070 70-Amp Switch Mode BEC Brushless Electronic Speed Controller (ESC). Please read this manual thoroughly before installation and operation to ensure proper function and to prevent damage to the unit or other components.
Bezpečnostní opatření
Operating an Electronic Speed Controller (ESC) in a remote-controlled aircraft requires adherence to strict safety guidelines. Failure to follow these precautions can result in serious injury or property damage.
- Bezpečnost baterie: Always handle LiPo batteries with extreme care. Do not overcharge, over-discharge, or short-circuit batteries. Store batteries in a fire-safe container.
- Připojení motoru: Ensure all motor connections are secure and insulated to prevent short circuits.
- Bezpečnost vrtule: Always remove the propeller from the motor before performing any setup, testing, or maintenance on the ESC or motor. An unexpected motor start can cause severe injury.
- Voda a vlhkost: Keep the ESC away from water and moisture. Exposure can cause damage and malfunction.
- Řízení tepla: Regulátory ESC mohou během provozu generovat značné teplo. Zajistěte dostatečné proudění vzduchu pro chlazení. Nedotýkejte se regulátoru ESC bezprostředně po použití.
- Správná polarita: Always connect the battery to the ESC with correct polarity. Reverse polarity will instantly damage the ESC.
- svtage and Current Limits: Nepřekračujte stanovený objemtage and current limits of the ESC.
Konec produktuview
The E-flite EFLA1070 is a 70-Amp Switch Mode BEC Brushless Electronic Speed Controller designed for remote-controlled aircraft. It features an integrated Switch Mode Battery Eliminator Circuit (BEC) to provide power to your receiver and servos, eliminating the need for a separate receiver battery. It comes equipped with an EC3 connector for battery input.
Image: The E-flite EFLA1070 70-Amp Switch Mode BEC Brushless ESC. This image shows the compact black unit with red and black battery input wires terminating in an EC3 connector, and three black motor output wires. The label on the ESC clearly displays "E-flite EFLA1070 70 Amp Switch Mode BEC Brushless ESC".
Nastavení a instalace
Proper installation is crucial for the performance and safety of your aircraft. Follow these steps carefully:
- Montáž regulátoru otáček: Securely mount the ESC in a location that allows for adequate airflow to prevent overheating. Use double-sided tape or zip ties.
- Připojení motoru: Připojte tři vodiče motoru z regulátoru (ESC) ke třem vodičům vašeho bezkartáčového motoru. Pořadí zapojení může ovlivnit směr otáčení motoru. Pokud se motor otáčí špatným směrem, prohoďte kterékoli dva ze tří vodičů motoru.
- Připojení baterie: Connect the battery input wires (red and black) of the ESC to your flight battery, ensuring correct polarity. The EFLA1070 is equipped with an EC3 connector.
- Připojení přijímače: Plug the throttle lead from the ESC into the throttle channel (typically channel 1 or 3, depending on your radio system) of your receiver.
- Kalibrace rozsahu škrticí klapky:
- Turn on your transmitter and set the throttle trim to its lowest position.
- Move the throttle stick to its maximum (full throttle) position.
- Připojte letový akumulátor k regulátoru (ESC). Regulátor (ESC) vydá sérii pípnutí.
- Once the beeps indicate it's ready (refer to your motor's manual for specific beep patterns if available), move the throttle stick to its minimum (full brake/off) position.
- The ESC will emit a confirmation tone, indicating the throttle range is calibrated.
- Test Motor Rotation: With the propeller removed, slowly advance the throttle to confirm correct motor rotation and smooth operation.
Operace
Once installed and calibrated, operating the ESC is straightforward:
- Sekvence zapnutí: Always turn on your transmitter first, then connect the flight battery to the ESC.
- Zajištění: After connecting the battery, the ESC will typically arm itself after a few seconds, indicated by a series of tones. Ensure the throttle stick is at its lowest position for arming.
- Ovládání škrticí klapky: Use the throttle stick on your transmitter to control motor speed.
- Sekvence vypínání: Disconnect the flight battery from the ESC first, then turn off your transmitter.
- BEC Function: The integrated Switch Mode BEC provides regulated power to your receiver and servos. Monitor your receiver voltage if your radio system allows.
Údržba
Regular inspection and basic maintenance will prolong the life of your ESC:
- Vizuální kontrola: Periodically check the ESC for any signs of physical damage, frayed wires, or burnt components.
- Kontrola konektoru: Ensure all connectors (battery, motor, receiver) are clean and securely attached.
- Čistota: Keep the ESC free from dirt, dust, and debris. Use a soft brush or compressed air for cleaning.
- Monitorování tepla: After flights, check the temperature of the ESC. If it's excessively hot to the touch, investigate potential issues such as propeller size, motor load, or insufficient cooling.
Odstraňování problémů
Pokud narazíte na problémy s regulátorem otáček (ESC), podívejte se na následující běžné problémy a jejich řešení:
| Problém | Možná příčina | Řešení |
|---|---|---|
| Motor se netočí ani se koktá. | Incorrect motor wire connection, throttle not calibrated, low battery voltage, damaged motor or ESC. | Check motor wire connections, recalibrate throttle range, check battery charge, inspect motor and ESC for damage. |
| ESC se nadměrně zahřívá. | Over-propped motor, insufficient cooling, excessive current draw. | Reduce propeller size, ensure adequate airflow, check for binding in drivetrain. |
| Žádné napájení přijímače/serv. | BEC failure, incorrect receiver connection, damaged receiver. | Check receiver connection, test with a separate BEC or receiver battery, inspect receiver. |
| Motor spins in wrong direction. | Incorrect motor wire phasing. | Prohoďte libovolné dva ze tří vodičů k motoru. |
Specifikace
- Model: EFLA1070
- Typ: Brushless Electronic Speed Controller (ESC)
- Aktuální hodnocení: 70 Amps
- BEC Type: Přepnout režim
- Konektor baterie: EC3
- Rozměry produktu: 6.6 x 4 x 0.58 palce (16.76 x 10.16 x 1.47 cm)
- Hmotnost položky: 1.6 unce (45.36 gramů)
- Výrobce: Horizon Hobby
- Země původu: Čína
Záruka a podpora
For warranty information or technical support, please contact Horizon Hobby, the manufacturer of E-flite products. Keep your proof of purchase for any warranty claims. Detailed warranty terms and contact information can typically be found on the official Horizon Hobby webwebu nebo nahlédnutím do obalu produktu.
Podpora Horizon Hobby: www.horizonhobby.com/support
