Leviton 003-84026-0 Stainless Steel 2-Gang Power Outlet Receptacle Wallplate Instruction Manual

Zavedení

This manual provides instructions for the proper installation and maintenance of the Leviton 003-84026-0 Stainless Steel 2-Gang Power Outlet Receptacle Wallplate. Please read these instructions carefully before beginning installation.

Bezpečnostní informace

• Always turn off power at the circuit breaker or fuse box before installation or maintenance.
• Ensure all wiring connections comply with local electrical codes.
• Pokud si nejste jisti jakoukoli částí těchto pokynů, obraťte se na kvalifikovaného elektrikáře.
• Tento výrobek je určen pouze pro vnitřní použití.

Obsah balení

• Leviton 003-84026-0 Stainless Steel 2-Gang Wallplate
• Mounting Screws (typically included with wallplate)

Nastavení a instalace

1. Vypnout napájení: Locate the circuit breaker or fuse that controls the power to the outlet where the wallplate will be installed. Turn off the power completely. Verify power is off using a voltage tester.
2. Remove Old Wallplate: Carefully unscrew and remove the existing wallplate, if any.
3. Position New Wallplate: Align the Leviton 003-84026-0 wallplate over the electrical box, ensuring the openings match the receptacles.
4. Secure Wallplate: Insert the provided mounting screws into the designated holes on the wallplate and tighten them gently until the wallplate is flush with the wall. Do not overtighten, as this can damage the wallplate or the electrical box.
5. Obnovit napájení: Once the wallplate is securely installed, restore power at the circuit breaker or fuse box.

Návod k obsluze

The Leviton 003-84026-0 wallplate is a passive component designed to cover and protect electrical outlets. No specific operational steps are required beyond its proper installation. Ensure that the receptacles are fully accessible and that the wallplate does not obstruct their use.

Údržba

• Čištění: To clean the stainless steel wallplate, use a soft, damp cloth. For stubborn marks, a mild, non-abrasive cleaner suitable for stainless steel can be used. Avoid harsh chemicals or abrasive scrubbers, which can scratch the finish.
• Inspekce: Periodically inspect the wallplate for any signs of damage, such as cracks, discoloration, or loose screws. If damage is observed, turn off power and replace the wallplate.

Odstraňování problémů

• Nástěnná deska je uvolněná: Ensure mounting screws are tightened appropriately. Do not overtighten.
• Wallplate Does Not Sit Flush: Check for obstructions behind the wallplate or ensure the electrical box is properly recessed.
• Škrábance nebo změna barvy: Refer to the Maintenance section for cleaning instructions. Deep scratches may require replacement.

Specifikace

This diagram illustrates the precise dimensions of the 2-gang wallplate. It shows a width of 2.750 inches (69.85 mm) for each opening, a total width of 4.56 inches (115.9 mm) for the 2-gang configuration, and a height of 4.500 inches (114.30 mm). The thickness is 0.220 inches (5.59 mm). Screw hole spacing and opening dimensions are also detailed.

Informace o záruce

Leviton products are backed by a limited warranty. For specific warranty terms and conditions, please refer to the official Leviton webwebu nebo kontaktujte zákaznickou podporu. Uschovejte si doklad o koupi pro případ reklamace.

Podpora a kontakt

For technical assistance, product inquiries, or support, please visit the official Leviton webnebo kontaktujte jejich oddělení zákaznických služeb. Kontaktní informace obvykle naleznete na webových stránkách výrobce webmísto nebo obal produktu.

• Výrobce: Leviton
• Webmísto: www.leviton.com