Zavedení
This manual provides essential information for the proper installation, operation, and maintenance of the Watts Series 335 ASME rated Boiler Pressure Relief Valve. This valve is designed for hydronic systems, specifically for boilers up to 510,000 BTU at a 30 PSI (2.11 bar) set point. Its compact, all-bronze construction makes it suitable for various OEM boiler applications.
Obrázek 1: Přední strana view of the Watts 30 PSI Pressure Relief Valve, showing the bronze body and the pressure relief lever.
Bezpečnostní informace
Always follow local codes and regulations during installation and maintenance. Ensure the system is depressurized and cooled before attempting any work on the valve. Wear appropriate personal protective equipment (PPE).
- Ne tamper with the factory set pressure.
- Ensure proper discharge piping is installed to safely route discharged water.
- Regularly inspect the valve for signs of corrosion or damage.
Nastavení a instalace
The Watts 0342691 Pressure Relief Valve is designed for straightforward installation. It features a 3/4-inch female threaded inlet and a 3/4-inch FNPT outlet.
- Příprava: Ensure the boiler system is completely shut down, depressurized, and cooled. Drain any water from the system if necessary.
- Demontáž starého ventilu (pokud je k dispozici): Carefully unthread the existing pressure relief valve from the boiler.
- Aplikace těsnicího prostředku na závity: Apply an appropriate thread sealant (e.g., PTFE tape or pipe dope) to the male threads of the new Watts valve.
- Instalace nového ventilu: Thread the new valve into the boiler's pressure relief valve port. Tighten securely with a wrench, ensuring not to overtighten.
- Connect Discharge Piping: Attach appropriate discharge piping to the valve's outlet. This piping must be sized correctly and routed to a safe discharge point, preventing scalding or property damage.
- System Re-pressurization: Slowly re-pressurize the boiler system and check for any leaks around the newly installed valve and connections.
Obrázek 2: Strana view of the Watts 30 PSI Pressure Relief Valve, showing the compact design and connection points.
Provozní principy
The Watts 0342691 is an automatic pressure relief valve designed to protect hydronic heating systems from over-pressurization. It is factory-set to open at 30 PSI (Pounds per Square Inch). When the system pressure exceeds this set point, the valve will automatically open, discharging water to relieve the excess pressure and prevent damage to the boiler or system components. Once the pressure drops below the set point, the valve will automatically close.
The valve also features a manual test lever. This lever allows for periodic manual testing of the valve's operation. When the lever is lifted, the valve will open, discharging water. It is important to exercise caution when using the test lever, as hot water may be discharged.
Údržba
Regular maintenance ensures the longevity and proper function of your pressure relief valve.
- Roční kontrola: It is recommended to inspect the valve annually for any signs of corrosion, leaks, or damage.
- Ruční testování: The manual test lever should be operated at least once a year to ensure the valve is not seized and can open freely. When testing, lift the lever briefly to allow a small amount of water to discharge, then release it. Ensure the valve reseats properly without dripping. Note: Some experienced users advise against frequent manual testing on older systems due to the risk of dislodging sediment and causing a leak. Consult a qualified technician if unsure.
- Čištění: Keep the exterior of the valve clean. Do not use harsh chemicals that could damage the bronze finish.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Valve constantly dripping or leaking |
|
|
| Valve does not open when pressure is high |
|
|
Specifikace
Figure 3: The Watts 30 PSI Pressure Relief Valve demonstrating its compact size, approximately 2.9 inches (7 cm) in height.
| Atribut | Hodnota |
|---|---|
| Číslo modelu | WATTS - 118946 |
| Materiál | Bronz |
| Velikost vstupního připojení | 3/4 palců |
| Typ vstupního připojení | Female Threaded |
| Velikost výstupního připojení | 3/4 palců |
| Typ výstupního připojení | FNPT |
| Maximální provozní tlak | 30 PSI (2.11 barů) |
| Hodnocení BTU | Až 20 000 BTU |
| Počet portů | 2 |
| Rozměry (D x Š x V) | 3 x 2.3 x 1.8 palce |
| Hmotnost | 0.01 ounces (Note: This seems unusually low, likely a data entry error in source. Actual weight for such a valve would be higher.) |
| Specifikace splněna | ASME Section IV |
Informace o záruce
Specific warranty details for this product are not provided in this manual. Please refer to the manufacturer's official website or contact Watts customer service for current warranty terms and conditions.
Podpora a kontakt
For technical assistance, replacement parts, or further information, please contact Watts customer support or visit their official webmísto.
Watts Official Webmísto: www.watts.com
Watts Store on Amazon: Visit the Watts Store
