Tunze USA 6055.000 Nano Stream Propeller Pump Instruction Manual

1. Úvod

The Tunze USA 6055.000 Nano Stream Propeller Pump is designed for efficient water circulation in aquariums. This pump features electronic speed control, allowing for adjustable flow rates to suit various aquatic environments. It is suitable for aquariums ranging from 40 to 500 liters (10 to 135 US gallons).

Klíčové vlastnosti:

• Tichý provoz: Navrženo pro minimální hluk během používání.
• 3D Adjustability: Allows for flexible positioning and direction of water flow.
• Strong Magnet Mount with Silence Clamp: Secure and vibration-reducing mounting for glass thicknesses up to 15mm (1/2").
• Elektronické ovládání rychlosti: Enables precise adjustment of flow rate.

Figure 1: Tunze Nano Stream 6055.000 Key Features Diagram

2. Bezpečnostní pokyny

Před použitím čerpadla si prosím přečtěte a pochopte všechny bezpečnostní pokyny. Nedodržení těchto pokynů může vést k úrazu elektrickým proudem, požáru nebo vážnému zranění.

• Always disconnect the power supply before performing any maintenance, installation, or removal of the pump.
• Ensure the pump is fully submerged in water during operation. Running the pump dry can cause damage.
• Nepoužívejte čerpadlo, pokud je poškozený napájecí kabel nebo zástrčka.
• This pump is designed for indoor aquarium use only.
• Uchovávejte mimo dosah dětí.
• Z bezpečnostních důvodů se ujistěte, že elektrická zásuvka má proudový chránič (GFCI).
• Do not attempt to modify or repair the pump yourself. Contact qualified personnel for service.

3. Obsah balení

Po vybalení ověřte, zda jsou všechny součásti přítomny a v dobrém stavu.

• Tunze Nano Stream Propeller Pump 6055.000
• Magnet Holder with Silence Clamp
• Power Supply Unit (100-240V / 50-60Hz)
• Návod k použití

Obrázek 2: Balení a obsah produktu

4. Nastavení a instalace

Follow these steps for proper installation of your Tunze Nano Stream Propeller Pump.

4.1 Umístění čerpadla

• Position the pump in your aquarium to achieve optimal water flow and circulation. Avoid placing it directly against the substrate to prevent stirring up debris.
• The 3D adjustability allows you to direct the flow as needed.

Figure 3: Tunze Nano Stream 6055.000 Propeller Pump

4.2 Mounting with Magnet Holder

1. Ensure the aquarium glass is clean and free of algae or debris where the pump will be mounted.
2. Place the pump unit with its internal magnet on the inside of the aquarium glass.
3. Align the external magnet holder on the outside of the aquarium glass, directly opposite the pump unit. The strong magnets will secure the pump in place.
4. Adjust the pump's angle and direction as desired. The Silence Clamp helps reduce vibrations.

The magnet holder is suitable for glass thicknesses up to 15mm (1/2").

Figure 4: Pump Mounted on Aquarium Glass

4.3 Připojení napájení

• Connect the pump's power cable to the provided power supply unit.
• Plug the power supply unit into a suitable electrical outlet. Ensure the outlet is protected by a GFCI.

5. Návod k obsluze

The Tunze 6055.000 Nano Stream Propeller Pump features electronic speed control for flexible operation.

5.1 Electronic Speed Control

The pump's flow rate can be adjusted from 1,000 to 5,500 liters per hour (250 to 1,450 US gallons per hour). This adjustment is typically done via a compatible controller (e.g., Tunze controllers 7092, 7095, and 7096, sold separately). Refer to your controller's manual for specific adjustment procedures.

5.2 První spuštění

• Once installed and connected to power, the pump will begin operating.
• Observe the water flow and adjust the pump's position or speed as necessary to achieve desired circulation patterns in your aquarium.

Obrázek 5: Přední strana View of Pump with Propeller

6. Údržba

Regular maintenance ensures optimal performance and longevity of your pump. Always disconnect power before maintenance.

6.1 Čištění čerpadla

Over time, algae and debris can accumulate on the pump's impeller and housing, reducing efficiency. Clean the pump regularly, typically every few months or as needed.

1. Odpojte čerpadlo od napájení.
2. Vyjměte čerpadlo z akvária.
3. Carefully disassemble the pump housing to access the impeller. The front grille can be twisted or unclipped.
4. Remove the impeller and its ceramic shaft.
5. Clean all components (housing, impeller, shaft) with a soft brush and warm water. For stubborn deposits, a mild vinegar solution can be used, followed by thorough rinsing.
6. Inspect the impeller and shaft for any signs of wear or damage. Replace if necessary.
7. Znovu sestavte čerpadlo a ujistěte se, že všechny díly jsou správně usazeny.
8. Return the pump to the aquarium and reconnect power.

The following video demonstrates the disassembly process for a similar Tunze Nano Stream pump (model 6015), which can be used as a guide for the 6055.000 model:

Video 1: Disassembly and Cleaning of Tunze Turbelle® nanostream® 6015 (similar to 6055.000)

7. Řešení problémů

If you encounter issues with your pump, refer to the following common problems and solutions.

7.1 Pump Not Starting or Weak Flow

• Zkontrolujte napájení: Ensure the pump is properly plugged in and the power outlet is functional. Verify the power supply unit is connected correctly.
• Ucpání oběžného kola: Disconnect power, remove the pump, and check the impeller for any debris (algae, sand, snails) that might be blocking it. Clean as described in the Maintenance section.
• Vzduchový uzávěr: Ensure the pump is fully submerged and gently shake it to release any trapped air.
• Nastavení ovladače: If using a controller, check its settings to ensure the flow rate is not set to minimum or off.

7.2 Nadměrný hluk nebo vibrace

• Impeller Damage/Wear: Inspect the impeller and ceramic shaft for damage or wear. A worn impeller can cause rattling. Replace if necessary.
• Trosky: Clean the impeller and housing thoroughly.
• Montáž: Ensure the magnet holder is securely attached and the Silence Clamp is properly engaged to minimize vibrations against the glass.
• Vzduchové bubliny: Trapped air can cause noise. Ensure the pump is fully submerged and free of air.

7.3 Pump Stops Intermittently

• Přehřívání: Ensure the pump is adequately cooled by water flow. Check for obstructions.
• Kolísání výkonu: Ověřte stabilní napájení.
• Problémy s ovladačem: If using a controller, check its programming or connection.

8. Specifikace

9. Záruka a podpora

For warranty information, technical support, or replacement parts, please contact Tunze USA LLC directly or refer to their official webUschovejte si doklad o koupi pro případ reklamace.