Návod k obsluze tlumiče pérování QA1 DS403 Proma Star Twintube

1. Úvod

This manual provides essential information for the proper installation, adjustment, and maintenance of your QA1 DS403 Proma Star Twintube Shock Absorber. Adhering to these instructions will ensure optimal performance and longevity of the product. Please read this manual thoroughly before proceeding with any installation or adjustment.

2. Konec produktuview

The QA1 DS403 is a Proma Star Twintube Shock Absorber designed for vehicle-specific applications. It features a single adjustable design, allowing for precise tuning of damping characteristics. Constructed from threaded aluminum with an anodized exterior finish, this shock absorber offers durability and performance.

• Typ: Proma Star Twintube Shock
• Nastavitelnost: Single Nastavitelný
• Materiál: Threaded Aluminum
• Dokončit: Eloxovaný
• Compressed Length: 11.125 palců
• Prodloužená délka: 15.00 palců
• Vnější průměr: 2.00 palců

Figure 2.1: QA1 DS403 Proma Star Twintube Shock Absorber and associated mounting hardware. This image displays the main shock body, two threaded collars, a spring seat, and various bushings and washers, illustrating the complete assembly.

3. Specifikace

Figure 3.1: Visual representation of the QA1 DS403 Shock Absorber with approximate length measurements indicated. The image shows the shock absorber held vertically, with a ruler graphic indicating a length of approximately 13 inches (33 cm).

4. Nastavení a instalace

Důležité: Professional installation is recommended. Improper installation can lead to vehicle damage or personal injury. Always refer to your vehicle's service manual for specific removal and installation procedures.

1. Bezpečnost především: Ensure the vehicle is securely supported on jack stands on a level surface. Disconnect the battery if working near electrical components.
2. Odstranit Old Shock: Carefully remove the existing shock absorber according to your vehicle manufacturer's instructions. This typically involves unbolting the upper and lower mounting points.
3. Zkontrolujte montážní body: Clean and inspect all mounting points for damage, wear, or corrosion. Replace any worn components.
4. Prepare New Shock: If applicable, install any necessary bushings or sleeves onto the QA1 DS403 shock absorber. Ensure all components are correctly oriented.
5. Nainstalujte nový šok: Position the QA1 DS403 shock absorber into the mounting locations. Secure the upper and lower mounting bolts, but do not fully tighten them until the vehicle is at ride height.
6. Konečné utažení: Once the vehicle is on the ground and at its normal ride height, fully tighten all mounting bolts to the vehicle manufacturer's specified torque values.
7. Zkontrolujte vůli: Verify that the shock absorber has adequate clearance from all suspension and chassis components throughout its full range of motion.

Obrázek 4.1: Detailní view of the QA1 DS403 Shock Absorber, highlighting the threaded body and mounting eyelets. This image provides a clear look at the construction and finish of the shock absorber, which is crucial for proper installation and inspection.

5. Obsluha a seřízení

The QA1 DS403 is a single adjustable shock absorber, meaning it allows for adjustment of both compression and rebound damping simultaneously with a single knob or dial. This adjustment affects the overall stiffness of the shock's resistance to movement.

5.1 Postup nastavení

1. Vyhledejte nastavovací knoflík: The adjustment knob is typically located at the bottom or top of the shock body.
2. Understand Clicks: The adjustment mechanism usually operates in "clicks." Turning the knob will increase or decrease damping. Refer to QA1's specific documentation for the total number of clicks and their effect.
3. Počáteční nastavení: Start with a recommended baseline setting (often provided by QA1 or found in performance guides). A common starting point might be midway through the adjustment range.
4. Úprava Damping:
   • Turning the knob clockwise generally increases damping (firmer ride).
   • Turning the knob counter-clockwise generally decreases damping (softer ride).
5. Testování a upřesňování: After making adjustments, test the vehicle in a safe environment. Make small, incremental changes and note the effect on ride quality and handling. Adjust all shocks equally for balanced performance.

Poznámka: Always adjust shocks in pairs (front or rear) to maintain vehicle balance. Consult QA1's official resources for detailed adjustment guidelines specific to your application.

6. Údržba

Regular maintenance ensures the longevity and consistent performance of your QA1 DS403 shock absorbers.

• Pravidelná kontrola: Periodically inspect the shocks for signs of leaks, damage to the body or shaft, worn bushings, or loose mounting hardware.
• Čištění: Keep the shock bodies clean, especially the threaded sections and adjustment mechanisms, to prevent dirt and debris from affecting performance or causing wear. Use mild soap and water, then rinse thoroughly.
• Pouzdra: Check rubber or polyurethane bushings for cracks, hardening, or excessive wear. Replace them if necessary to prevent noise and maintain proper articulation.
• Montážní hardware: Verify that all mounting bolts are torqued to specification. Loose hardware can lead to noise, premature wear, and unsafe conditions.
• Shaft Protection: Ensure the shock shaft is free from nicks, scratches, or corrosion, as these can damage the internal seals and lead to fluid leaks.

7. Řešení problémů

This section addresses common issues you might encounter with your shock absorbers.

7.1 Běžné problémy a řešení

• Nadměrné poskakování nebo špatná kvalita jízdy:
  • Příčina: Damping set too soft, worn internal components, or incorrect spring rate.
  • Řešení: Zvýšit damping (turn adjustment knob clockwise). Inspect for leaks or damage. Ensure correct spring rate for vehicle weight.
• Harsh Ride or Lack of Suspension Travel:
  • Příčina: Damping set too stiff, incorrect spring rate, or shock bottoming out.
  • Řešení: Decrease damping (turn adjustment knob counter-clockwise). Verify correct spring rate. Check for proper shock length for application.
• Noise (Clunking, Squeaking):
  • Příčina: Loose mounting hardware, worn bushings, or internal shock damage.
  • Řešení: Tighten all mounting bolts to specification. Inspect and replace worn bushings. If noise persists and no external cause is found, the shock may require professional inspection or replacement.
• Úniky kapalin:
  • Příčina: Damaged seals, bent shaft, or manufacturing defect.
  • Řešení: A leaking shock absorber indicates internal damage and requires replacement. Do not attempt to repair.

If troubleshooting steps do not resolve the issue, contact QA1 customer support or a qualified automotive technician.

8. Záruka a podpora

For specific warranty information regarding your QA1 DS403 Proma Star Twintube Shock Absorber, please refer to the official QA1 website or the documentation provided at the time of purchase. QA1 products are designed for performance and durability, and the company stands behind its products with a commitment to quality.

For technical assistance, product inquiries, or warranty claims, please contact QA1 directly:

• Oficiální QA1 Webmísto: www.qa1.net
• Zákaznická podpora: Refer to the "Contact Us" section on the official QA1 webweb s telefonními čísly, e-mailovými adresami nebo online formuláři podpory.

Always provide your product model number (DS403) and purchase details when contacting support to expedite assistance.