Zavedení
This manual provides detailed instructions for the installation, operation, and maintenance of your Wolo Apollo 8 GEN 3 LED Emergency Warning Light, Model 3095PPM-C. Please read this manual thoroughly before use to ensure proper function and safety.
The Wolo Apollo 8 GEN 3 LED Emergency Warning Light, Model 3095PPM-C, features a clear lens and a robust design for various mounting applications.
Důležité bezpečnostní pokyny
- Ujistěte se, že všechna elektrická připojení jsou bezpečná a řádně izolovaná, aby se zabránilo zkratu.
- Verify the vehicle's electrical system voltage matches the light's operating voltage (12-60V DC).
- Před zahájením instalace odpojte baterii vozidla, abyste předešli úrazu elektrickým proudem.
- Světlo bezpečně namontujte, aby se během provozu vozidla neoddělilo.
- Adhere to all local and national regulations regarding the use of emergency warning lights.
Obsah balení
- Wolo Apollo 8 GEN 3 LED Emergency Warning Light (Model 3095PPM-C)
- Montážní materiál (šrouby, matice, podložky)
- Drátové terminály
- Držák pojistky
- Gumové těsnění
- Návod k použití (tento dokument)
Nastavení a instalace
The Apollo 8 warning light offers two primary mounting options: permanent surface mount or pipe mount.
Permanent Surface Mount
- Choose a flat, stable surface on your vehicle for mounting. Ensure the location provides clear 360° visibility.
- Use the provided rubber gasket as a template to mark the drilling locations for the mounting screws.
- Na vyznačených místech vyvrtejte vodicí otvory.
- Secure the light base to the surface using the provided mounting hardware (screws, washers, nuts). Ensure a tight fit to prevent vibration.
- Route the power wires to the vehicle's electrical system. Connect the positive wire (typically red) to a switched 12-60V DC power source via the in-line fuse holder. Connect the negative wire (typically black) to a suitable ground point on the vehicle chassis.
- Ensure all wire connections are secure and protected from moisture and abrasion.
Montáž na trubku
- Identify a suitable pipe or pole for mounting. The light is designed to fit standard pipe sizes.
- Use the provided hardware to secure the light base to the pipe.
- Route the power wires and connect them as described in the Permanent Surface Mount section.
Note: Professional installation is recommended if you are unfamiliar with vehicle electrical systems.
Návod k obsluze
The Wolo Apollo 8 features eight (8) selectable warning light patterns.
- Once the light is powered on, it will activate in the last selected flash pattern.
- To change the flash pattern, momentarily press the pattern selection button (located on the unit or via a control wire).
- Each press of the button will cycle to the next available warning light pattern.
- Release the button when the desired pattern is displayed. The light will retain this pattern until changed again or power is disconnected.
Údržba
- Čištění: Clean the clear polycarbonate lens periodically with a soft cloth and mild soap solution. Avoid abrasive cleaners or solvents that could damage the lens.
- Výměna objektivu: The lens is replaceable. If the lens becomes damaged, contact Wolo customer support for replacement parts and instructions.
- Kontrola elektroinstalace: Periodically inspect all wiring and connections for signs of wear, corrosion, or damage. Ensure connections remain secure.
- The GEN 3 LEDs are designed for long life and are maintenance-free, requiring no bulb replacement.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Světlo nesvítí | Žádné napájení | Check power connections, fuse, and vehicle battery. Ensure the light is receiving 12-60V DC. |
| Light flashes erratically | Volné zapojení kabeláže nebo nesprávný hlasitosttage | Inspect all wiring connections for tightness. Verify input voltage je v rozsahu 12–60 V DC. |
| Cannot change flash pattern | Faulty pattern selection button or control circuit | Ensure the button is functioning correctly. If the issue persists, contact customer support. |
| Snížený světelný výkon | Špinavý objektiv | Clean the lens with a soft cloth and mild soap solution. |
Technické specifikace
- Model: 3095PPM-C
- Světelný zdroj: 20 x 1-watt GEN 3 LEDs
- Provozní svtage: 12 - 60 Volts DC
- Peak Current Draw: 1.37 Amps
- Light Patterns: 8 selectable patterns
- Materiál čočky: Polycarbonate Plastic (Clear)
- Základní materiál: Aluminum (Painted Black)
- Možnosti montáže: Permanent Surface Mount, Pipe Mount
- Speciální vlastnosti: Waterproof, Encapsulated Microprocessor, Reduced EMI
- Rozměry: Přibližně 6.63 x 6.75 x 6.5 palce
- Hmotnost: Přibližně 1.85 libry
Záruka a podpora
Wolo products are designed for durability and performance. For specific warranty details, please refer to the warranty card included with your product or visit the official Wolo webmísto.
Zákaznická podpora
For technical assistance, replacement parts, or warranty claims, please contact Wolo customer support.
Wolo Manufacturing Corp.
Deer Park, NY 11729
