Zavedení
This manual provides detailed instructions for the installation, operation, and maintenance of your Claber 90763 Timer Kit 20 Practico. This automatic drip irrigation system is designed for watering up to 20 potted plants on terraces or patios, ensuring efficient and consistent hydration.
Bezpečnostní informace
- Bez mrazu: Do not expose the timer or system components to freezing temperatures.
- Nevhodné pro děti: Uchovávejte výrobek mimo dosah dětí.
- Pouze pro venkovní použití: Tento výrobek je určen pro venkovní instalaci.
- Neponořovat: The timer unit must not be placed underwater.
- Instalace ventilové skříně: Do not install the timer inside a valve box.
- Tlak vody: Ensure water pressure is between 0.5 bar (7.3 psi) and 10 bar (145 psi).
Obsah balení
Ověřte, zda jsou ve vaší sadě přítomny všechny komponenty:
Image: All components of the Claber 90763 Timer Kit 20 Practico, including the timer, main hose, drippers, stakes, and connectors.
- 1x Aquauno Pratico Timer
- 1x Pressure Stabilizer
- 1x 20m (1/4" - 4-6mm) Main Hose
- 20x Adjustable Drippers
- 20x Stakes for Drippers
- Various Connectors and Fittings (e.g., 3-way connectors, end caps)
Pokyny pro nastavení
1. Instalace baterie
- Open the battery compartment on the back of the Aquauno Pratico timer.
- Insert one new 9V alkaline battery, ensuring correct polarity.
- Bezpečně uzavřete přihrádku na baterie.
Image: A section from the instruction manual illustrating the steps for inserting a 9V battery into the timer.
Poznámka: The timer requires a 9V alkaline battery (not included). If the battery is low, the timer's LED will flash. Replace the battery promptly to avoid interruption of watering cycles.
2. Timer and Pressure Stabilizer Installation
- Attach the pressure stabilizer to the outlet of the Aquauno Pratico timer.
- Screw the timer onto a standard 3/4" outdoor tap. Ensure a tight, leak-free connection.
- The timer should be installed vertically, with the display facing outwards for easy access.
Image: The Claber Aquauno Pratico timer connected to an outdoor water tap, with the pressure stabilizer attached below it.
3. Drip System Assembly
- Connect the main hose (1/4" or 4-6mm) to the outlet of the pressure stabilizer.
- Lay out the main hose to reach all potted plants you intend to water.
- At each plant location, cut the main hose and insert a 3-way connector or a direct dripper connection.
- Attach the adjustable drippers to the hose or connectors.
- Use the provided stakes to secure the drippers near the base of each plant.
- Cap the end of the main hose with an end cap to maintain pressure.
Image: An illustration of a balcony with potted plants being watered by the Claber drip irrigation system, showing hose routing and dripper placement.
Návod k obsluze
1. Programming the Aquauno Pratico Timer
The Aquauno Pratico timer allows for daily watering with a maximum duration of 60 minutes. Refer to the timer's interface for specific programming steps:
Obrázek: Podrobný view of the Claber Aquauno Pratico timer, showing the control buttons and display area.
- Tlačítko Start (zelené): Press to initiate a watering cycle or confirm a setting.
- Tlačítko Stop (červené): Press to stop an ongoing watering cycle or cancel a setting.
- Programovací volič: Rotate the dial to select the desired watering duration (e.g., 5, 10, 15, 20, 30, 45, 60 minutes). The timer will automatically water daily for the selected duration.
- Reset/Cancel Button: Use to reset the timer or cancel current programming.
For detailed programming steps, refer to the specific instructions provided on the timer unit or the full manual available online.
2. Adjusting Drippers
Each dripper is adjustable to control the water flow to individual plants. Rotate the cap on each dripper to increase or decrease the water output. Adjust the flow based on the plant's water requirements and soil type.
Údržba
- Čištění: Wipe the timer and components with a damp cloth as needed. Do not use abrasive cleaners.
- Čištění filtru: The timer includes a filter at the inlet. Periodically remove and clean this filter to prevent blockages and ensure proper water flow.
- Zima: Before the first frost, disconnect the timer and drain all water from the system. Store the timer and components in a dry, frost-free location. Remove the battery before storage.
- Výměna baterie: Replace the 9V alkaline battery annually or when the low battery indicator flashes.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Timer does not start watering. | Dead or low battery. Incorrect programming. Water tap is off. | Replace battery. Re-program the timer. Ensure water tap is fully open. |
| No water flow from drippers. | Clogged filter. Kinked hose. Drippers are closed. Low water pressure. | Clean the inlet filter. Check hose for kinks. Open drippers. Ensure adequate water pressure. |
| Z přípojek uniká voda. | Loose connections. Damaged O-rings/washers. | Tighten all connections. Inspect and replace any damaged O-rings or washers. |
| Nepravidelná zálivka. | Uneven water pressure. Partially clogged drippers. | Ensure pressure stabilizer is correctly installed. Clean drippers. |
Specifikace
- Značka: Claber
- Model: 90763 (Timer Kit 20 Practico)
- Materiál: Plast
- Product Dimensions (Timer): 2.36"H x 3.15"Š x 4.33"V
- Item Weight (Timer): Approximately 0.037 ounces (1.05 Grams)
- Frekvence zalévání: Denní
- Délka zalévání: Up to 60 minutes (adjustable)
- Zdroj napájení: 1x 9V Alkaline Battery (not included)
- Rozsah tlaku vody: 0.5 - 10 bar (7.3 - 145 psi)
- Pokyny pro péči: Otřete pomocí Damp Tkanina
Záruka a podpora
For warranty information, technical support, or additional resources, please visit the official Claber webnebo kontaktujte jejich zákaznický servis.
Online zdroje: Claber Instruction Manuals
Výrobce: Claber
