OWON PDS5022T Portable Digital Storage Oscilloscope and Digital Multimeter

Zavedení

The OWON PDS5022T is a 25 MHz, two-channel portable digital oscilloscope designed for various electronics applications, including circuit testing, electrical engineering education, and hobbyist projects. It features a maximum real-time sample rate of 100 MS/s and a record length of 5 kpts per channel, enabling detailed waveform acquisition. The device incorporates edge and video triggering, two basic math functions, FFT (Fast Fourier Transform), 20 automatic measurements, and an auto-scale function. Connectivity is provided via USB for PC integration.

Co je v krabici?

• OWON PDS5022T portable digital oscilloscope
• (2) Passive voltage probes
• CD-ROM PC software
• kabel rozhraní USB
• Power cord (for 100 to 240VAC, 50/60Hz, CAT II)
• Návod k použití

Nastavení

1. Připojení napájení: Connect the provided power cord to the oscilloscope and a suitable power outlet (100 to 240VAC, 50/60Hz). The device can also operate on a rechargeable lithium-ion battery (sold separately).
2. Připojení sondy: Attach the passive voltage probes to the CH1 and CH2 input BNC connectors on the front panel. Ensure a secure connection.
3. Kompenzace sondy: Before taking measurements, perform probe compensation. Connect the probe tip to the PROBE COMP terminal (typically 5V, 1kHz square wave) and the ground clip to the ground terminal. Adjust the compensation trimmer on the probe until a flat-top square wave is displayed on the screen.
4. Počáteční zapnutí: Press the power button to turn on the oscilloscope. The 8-inch color TFT-LCD will display the startup sequence.
5. PC Software Installation (Optional): If connecting to a PC for data transmission or remote operation, install the provided software from the CD-ROM onto your computer. Connect the oscilloscope to the PC using the USB interface cable.

Návod k obsluze

The front panel of the PDS5022T features a clear layout for intuitive operation. Refer to the image above for control locations.

Ovládací prvky na předním paneluview

• Zobrazit: 8-inch color TFT-LCD with 640 x 480 pixel resolution for waveform viewIng.
• Funkční tlačítka (F1-F5): Context-sensitive buttons located to the right of the display, used to select options from on-screen menus.
• Vertical Controls (VOLTS/DIV, POSITION): Independent controls for Channel 1 (CH1) and Channel 2 (CH2). The VOLTS/DIV knobs adjust the vertical scale (voltage per division), while the POSITION knobs adjust the vertical position of the waveform.
• Horizontal Controls (SEC/DIV, POSITION): The SEC/DIV knob adjusts the horizontal time base (seconds per division), and the horizontal POSITION knob shifts the waveform left or right.
• Trigger Controls (TRIG LEVEL, TRIG MENU, SET TO 50%, FORCE TRIG, SET TO ZERO): These controls manage how the oscilloscope synchronizes with the input signal. The TRIG LEVEL knob sets the voltage level at which the trigger occurs.
• Vstupní konektory: BNC connectors for CH1, CH2, and EXT TRIG (external trigger). The EXT TRIG allows triggering from a third source.
• Utility Buttons:
  • SAVE/RCL: Saves or recalls waveform data and settings. Up to four waveforms can be stored internally.
  • OPATŘENÍ: Accesses automatic measurement functions (e.g., period, frequency, peak-to-peak).
  • KURZOR: Activates and controls screen cursors for manual voltage and time measurements.
  • ACQUIRE: Configures acquisition settings.
  • ZOBRAZIT: Adjusts display settings.
  • NABÍDKY: Navigates through various menu options.
  • AUTOSET: Automatically adjusts vertical, horizontal, and trigger settings to display a stable waveform.
  • AUTOSCALE: Similar to AUTOSET, selects optimal settings for displaying a waveform. Can be disabled for educational purposes.
  • RUN/STOP: Spouští nebo zastavuje snímání průběhu.
• Math Menu: Provides access to waveform math functions, including addition, subtraction, and FFT (Fast Fourier Transform).

Základní kroky provozu

1. Připojení signálu: Connect the probe from the desired channel (CH1 or CH2) to the circuit point you wish to measure.
2. Zapnutí: Turn on the oscilloscope.
3. Auto-Setup: Stiskněte tlačítko AUTOSET or AUTOSCALE button to quickly obtain a stable display of the input signal.
4. Upravit vertikální měřítko: Použijte VOLTS/DIV knob for the active channel to adjust the vertical sensitivity, making the waveform fit the screen appropriately.
5. Upravit horizontální měřítko: Použijte SEC/DIV knob to adjust the time base, allowing you to view více či méně horizontálně tvaru vlny.
6. Úprava spouště: Použijte TRIG LEVEL knob to stabilize the waveform. The trigger point is indicated on the screen. For complex waveforms, use the TRIG MENU to access advanced trigger settings like edge, video, and trigger hold-off.
7. Rozměry: Stiskněte tlačítko OPATŘENÍ button to display automatic measurements. Use the KURZOR button to activate and position cursors for manual measurements.
8. Matematické funkce: Stiskněte tlačítko MATH MENU button to perform operations like adding or subtracting channels, or performing an FFT analysis.
9. Ukládání dat: Použijte SAVE/RCL button to save waveform data or instrument settings to internal memory.

Údržba

• Čištění: Use a soft, dry cloth to clean the exterior of the oscilloscope. For stubborn dirt, a slightly damp cloth with mild detergent may be used. Avoid abrasive cleaners or solvents.
• Skladování: Zařízení skladujte na chladném a suchém místě mimo dosah přímého slunečního záření a extrémních teplot.
• Péče o sondu: Handle probes carefully. Avoid bending or stressing the cables excessively. Keep probe tips clean.
• Péče o baterii (pokud je k dispozici): If using a rechargeable battery, follow the manufacturer's guidelines for charging and storage to maximize battery life.

Odstraňování problémů

• Bez displeje/napájení: Ensure the power cord is securely connected and the power outlet is functional. If using battery, ensure it is charged.
• Nestabilní tvar vlny: Upravte TRIG LEVEL knob. Check trigger settings in the TRIG MENU. Ensure the input signal is within the oscilloscope's bandwidth and voltage rozsah.
• Není zobrazen žádný signál: Verify probes are correctly connected to both the oscilloscope and the circuit. Check probe compensation. Ensure the VOLTS/DIV a SEC/DIV settings are appropriate for the signal being measured.
• Zkreslený tvar vlny: Check probe compensation. Ensure the input signal does not exceed the oscilloscope's input voltage limity.
• Problémy s připojením k počítači: Verify USB cable connection. Ensure PC software is correctly installed and drivers are up to date.

Specifikace

Záruka a podpora

For warranty information and technical support, please refer to the documentation included with your product or contact OWON customer service. OWON products are manufactured by Fujian Lilliput Optoelectronics Technology, a company founded in 1993 and meeting International Organization for Standardization (ISO) standard 9001.