Liebherr FKUV 1612-21 Bottle Cooler Instruction Manual

1. Nastavení a instalace

Careful setup ensures optimal performance and longevity of your Liebherr bottle cooler.

1.1 Vybalení

Remove all packaging materials, including protective films and transport safety devices. Inspect the appliance for any transport damage. If damage is found, do not connect the appliance and contact your supplier immediately.

1.2 Umístění

• Place the appliance on a firm, level surface to ensure stability. Use the adjustable feet to level the unit if necessary.
• Ensure adequate ventilation. Maintain a minimum clearance of 5 cm (2 inches) around the sides and back of the appliance for proper air circulation. Do not block ventilation openings.
• Avoid direct sunlight and proximity to heat sources such as radiators, ovens, or cooktops, as these can increase energy consumption.
• The appliance is designed for indoor use. Do not install it in damp nebo vlhkých místech.

Image 1: Liebherr FKUV 1612-21 Bottle Cooler. This image shows the exterior of the bottle cooler, highlighting its compact design suitable for semi-industrial use.

1.3 Počáteční čištění

Before first use, clean the interior and all accessories with lukewarm water and a mild detergent. Rinse thoroughly and dry completely.

1.4 Elektrické připojení

Connect the appliance to a properly installed earthed socket. Ensure the voltage and frequency match the specifications on the rating plate. Do not use extension cords or multiple sockets.

1.5 Počáteční spuštění

After connecting to power, allow the appliance to run empty for approximately 2-3 hours to reach the desired operating temperature before loading bottles.

2. Návod k obsluze

Understanding the controls and features will help you maintain optimal conditions for your beverages.

2.1 Regulace teploty

The bottle cooler is equipped with an adjustable thermostat. To set the desired temperature, rotate the thermostat dial located inside the appliance. Turning the dial towards higher numbers typically results in colder temperatures. Allow several hours for the temperature to stabilize after adjustment.

2.2 Plnění lahví

• Distribute bottles evenly on the shelves to ensure proper air circulation and prevent overloading any single shelf.
• Avoid blocking the internal fan or air vents, as this can impair cooling performance.
• Do not place hot items directly into the cooler; allow them to cool to room temperature first.

2.3 Vnitřní osvětlení

If your model includes internal lighting, it is typically controlled by a switch located near the light fixture or on the control panel. Use the lighting to illuminate the contents as needed.

3. Údržba a péče

Regular maintenance ensures hygienic operation and extends the lifespan of your appliance.

3.1 Čištění interiéru

• Před čištěním odpojte spotřebič od napájení.
• Clean the interior regularly with lukewarm water and a mild, pH-neutral detergent. Avoid abrasive cleaners or solvents.
• Pay special attention to door seals; clean them with clear water and dry thoroughly to maintain their elasticity and sealing properties.
• Před opětovným připojením k napájení všechny povrchy důkladně osušte.

3.2 Čištění exteriéru

Vnější povrchy otřete měkkým, damp cloth. For stainless steel surfaces, use a specialized stainless steel cleaner if necessary, following the product instructions.

3.3 Odmrazování

This appliance features automatic defrosting. The evaporator thaws automatically, and the resulting condensation water evaporates. Ensure the drain opening at the back of the interior is not blocked to allow water to flow freely.

4. Řešení problémů

Než kontaktujete zákaznický servis, zkontrolujte prosím následující běžné problémy a jejich řešení:

• Appliance does not cool:
  • Check if the power plug is correctly inserted into the socket.
  • Verify if the fuse in your household electrical system is intact.
  • Ensure the temperature control is set correctly and not turned off.
• Teplota není dostatečně nízká:
  • Dvířka nemusí být správně zavřená.
  • Too much warm air may be entering due to frequent door openings.
  • The ventilation openings might be blocked.
  • Okolní teplota může být příliš vysoká.
  • The temperature setting might be too high (adjust to a colder setting).
• Neobvyklé zvuky:
  • Ujistěte se, že je spotřebič vodorovný a stabilní.
  • Check if any objects inside are vibrating against each other.
  • Normal operating noises include gurgling (refrigerant flow) and clicking (thermostat).
• Excessive condensation or ice formation:
  • Ujistěte se, že těsnění dvířek je čisté a neporušené.
  • Avoid leaving the door open for extended periods.
  • Check if the drain opening for condensation water is clear.

If the problem persists after checking these points, please contact Liebherr customer service.

5. Technické specifikace

Key technical data for the Liebherr FKUV 1612-21 bottle cooler:

6. Informace o záruce

Liebherr appliances are manufactured to the highest quality standards. This product comes with a manufacturer's warranty covering defects in materials and workmanship under normal use. The specific terms and duration of your warranty may vary by region and purchase date. Please refer to the warranty card included with your appliance or visit the official Liebherr webstránky pro podrobné informace.

To make a warranty claim, you will typically need your proof of purchase (receipt or invoice) and the appliance's model and serial number.

7. Zákaznická podpora

For further assistance, technical support, or to schedule service, please contact Liebherr customer service:

• Webmísto: Visit the official Liebherr webstránky pro váš region (např. home.liebherr.com) for FAQs, service locator, and contact details.
• Telefon: Refer to your local Liebherr contact information provided in the documentation accompanying your appliance.
• Servisní požadavek: Online service request forms are often available on the Liebherr webmísto.

When contacting support, please have your model number (FKUV 1612-21) and serial number ready to expedite the process.