Uživatelská příručka k přenosné sadě abrazivního tryskače Central Pneumatic

1. Důležité bezpečnostní informace

Read and understand this entire instruction manual before using this kit. Failure to follow all instructions may result in serious injury.

• Osobní ochranné prostředky (OOP): Always wear ANSI approved safety goggles, gloves, face mask, and hood when operating the abrasive blaster. Abrasive media can cause eye damage and other injuries.
• Bezpečný provoz: Never point the sandblasting gun at your face or exposed portions of your body. Never point the gun at any person or animal.
• Pracovní oblast: The blasting medium will accumulate and cover items near the blasting area, potentially damaging the finish or contaminating moving parts. Ensure the work area is clear of unintended targets.
• Chemické varování: This product, when used for sand blasting and similar applications, produces chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code § 25249.5 et seq.)
• Do not remove any warning labels from the product.

2. Konec produktuview

The Central Pneumatic Portable Abrasive Blaster Kit is designed for efficient removal of paint, rust, graffiti, corrosion, and scale. It is a portable unit that requires an external air compressor for operation.

2.1 Klíčové vlastnosti

• Hopper takes most abrasives: steel grit, glass beads, pecan shells, and more.
• Portable design for ease of use and transport.
• Requires a 1 HP or larger air compressor for optimal performance.

2.2 Součásti balení

• Výbušná zbraň
• Hopper (50 lb. capacity)
• Material Hose (15 ft.)
• 3mm šestihranný klíč

Figure 1: The Central Pneumatic Portable Abrasive Blaster Kit, showing the gray hopper, coiled black material hose, and the silver blast gun. The hopper has a top opening for media and a handle for portability.

3. Nastavení

1. Rozbalte komponenty: Opatrně vyjměte všechny součásti z obalu a zkontrolujte, zda nejsou poškozené.
2. Připojte hadici: Attach the 15 ft. material hose securely to the blast gun and the hopper outlet. Ensure all connections are tight to prevent air or media leaks.
3. Připojení vzduchového kompresoru: Connect your air compressor (1 HP or larger, capable of 3.5 CFM at 50 PSI minimum) to the air inlet on the blast gun. Use an appropriate air hose and fittings (not included).
4. Plnicí násypka: Open the top of the hopper and carefully fill it with your chosen abrasive media (e.g., steel grit, glass beads, pecan shells). Do not overfill; leave some space for air circulation. The hopper has a 50 lb. capacity.
5. Připravte pracovní plochu: Ensure the blasting area is well-ventilated and clear of any items that could be damaged by abrasive media. Set up appropriate containment if necessary.
6. Používejte OOPP: Before proceeding, put on all required personal protective equipment, including safety goggles, gloves, face mask, and hood.

4. Návod k obsluze

1. Ověřte připojení: Double-check all hose and air connections to ensure they are secure.
2. Turn on Air Compressor: Start your air compressor and allow it to build up to the required pressure (minimum 50 PSI).
3. Test Blasting: Point the blast gun at a scrap piece of material or a designated test area. Depress the trigger to begin blasting. Adjust air pressure or media flow as needed to achieve the desired result.
4. Začněte s tryskáním: Hold the blast gun at an appropriate distance and angle from the surface to be cleaned. Move the gun in a steady, even motion to ensure uniform coverage and material removal.
5. Monitor Media Level: Periodically check the abrasive media level in the hopper and refill as necessary.
6. Zastavte odstřelování: Release the trigger to stop the flow of abrasive media. Turn off the air compressor when finished with the task.
7. Odtlakování: Safely depressurize the system after use by disconnecting the air supply and bleeding any remaining air from the lines.

5. Údržba

• Po použití vyčistěte: After each use, empty any remaining abrasive media from the hopper and clean the hopper and hoses to prevent clogging and corrosion.
• Zkontrolujte hadice a spoje: Regularly inspect the material hose and all connections for wear, cracks, or damage. Replace any worn or damaged parts immediately.
• Check Nozzle: Inspect the blast gun nozzle for wear. A worn nozzle can affect blasting performance. Replace if necessary.
• Správně skladujte: Store the abrasive blaster kit in a clean, dry place, away from moisture and extreme temperatures.

6. Řešení problémů

7. Specifikace

• Název modelu: Portable Abrasive Blaster Kit
• Číslo modelu: 37025
• Značka: Centrální Pneumatické
• Minimum Air Requirement: 3.5 CFM při 50 PSI
• Kapacita násypky: 50 lb
• Délka hadice: 15 stop
• Materiál: Legovaná ocel
• Barva: Stříbro
• Zdroj napájení: Vzduch
• Hmotnost položky: 6 libry
• Rozměry produktu: 32 x 20 x 20 palce
• Zahrnuté komponenty: Blast Gun, Hopper, Material Hose, And 3mm Hex Key
• Doporučená použití: Surface Preparation, Cleaning, Stripping

8. Záruka a podpora

For warranty information or technical support, please refer to the original purchase documentation or contact Central Pneumatic customer service directly. Keep your purchase receipt for warranty claims.

Tento produkt je vyroben v Číně.