PSRKIT15 Prestige Igniter with Gasket User Manual

Zavedení

This manual provides essential information for the installation, operation, maintenance, and troubleshooting of the Triangle Tube PSRKIT15 Prestige Igniter with Gasket. This component is designed for use with Triangle Tube Prestige PS110, PS175, PS250, Solo 399, Solo 60, Solo 110, Solo 175, Solo 250, Solo 399, and Prestige Excellence 110 boilers.

The igniter is a critical part of the boiler's ignition system, responsible for initiating the combustion process. Proper installation and maintenance are crucial for safe and efficient boiler operation.

Bezpečnostní informace

Always prioritize safety when working with boiler systems. Installation and maintenance should only be performed by qualified and experienced technicians. Failure to follow safety guidelines can result in property damage, serious injury, or death.

• Disconnect all power to the boiler before beginning any work.
• Ensure the boiler system has cooled down sufficiently to prevent burns.
• Používejte vhodné osobní ochranné prostředky (OOP), včetně rukavic a ochrany očí.
• Refer to the main boiler manual for specific safety procedures and warnings.
• Verify gas supply is shut off before working on ignition components.

Nastavení a instalace

The PSRKIT15 igniter is a direct replacement part. Follow the specific installation instructions provided in your boiler's service manual. The general steps for replacement are outlined below:

1. Příprava: Ensure the boiler is powered off and the gas supply is closed. Allow the boiler to cool.
2. Přístup: Locate the igniter assembly within the boiler's combustion chamber. This may require removing access panels or other components.
3. Odpojení starého zapalovače: Carefully disconnect the electrical wiring from the old igniter. Note the orientation and connection points.
4. Demontáž starého zapalovače: Unfasten any mounting screws or clips securing the old igniter. Gently remove it, ensuring the old gasket is also removed.
5. Nainstalujte nové těsnění: Place the new gasket included with the PSRKIT15 kit onto the mounting surface. Ensure it is properly seated and aligned.
6. Instalace nového zapalovače: Carefully insert the new PSRKIT15 igniter into its position, aligning it with the mounting holes. Secure it with the appropriate fasteners. Do not overtighten.
7. Připojení kabeláže: Reconnect the electrical wiring to the new igniter, ensuring all connections are secure and correct.
8. Znovu sestavit: Replace any removed access panels or components.
9. Test: Restore gas and electrical power to the boiler. Initiate a call for heat and observe the ignition sequence to confirm proper operation of the new igniter. Check for any gas leaks.

Image: The Triangle Tube PSRKIT15 Prestige Igniter with Gasket. This image shows the igniter component, which consists of a ceramic body with two metal electrodes and a metal mounting bracket. A blue-grey gasket is visible attached to one end, ready for installation.

Provozní principy

The PSRKIT15 igniter functions as a hot surface igniter (HSI). When the boiler control board calls for heat, an electrical current is sent to the igniter, causing its ceramic element to heat up rapidly to a very high temperature. This incandescent surface then ignites the gas-air mixture in the combustion chamber. Once ignition is confirmed by the flame sensor, the igniter typically de-energizes, and the flame is sustained by the continuous flow of gas.

This igniter is designed for intermittent pilot applications, meaning it only energizes when there is a call for heat, providing a safe and efficient ignition method.

Údržba

Regular inspection of the igniter is recommended as part of routine boiler maintenance, typically performed annually by a qualified technician.

• Vizuální kontrola: Check the ceramic portion of the igniter for cracks, chips, or discoloration. Inspect the electrodes for signs of wear, corrosion, or carbon buildup.
• Čištění: If minor carbon buildup is present, carefully clean the igniter surface with a soft brush or fine-grit sandpaper. Avoid harsh chemicals or abrasive materials that could damage the ceramic.
• Stav těsnění: Always replace the gasket when replacing the igniter. Inspect the existing gasket during maintenance; if it shows signs of wear or damage, it should be replaced to ensure a proper seal.
• Elektrické připojení: Ujistěte se, že všechna elektrická připojení k zapalovači jsou čistá, těsná a bez koroze.
• Nahrazení: Igniters have a finite lifespan. If the igniter shows significant wear, damage, or is causing intermittent ignition issues, it should be replaced with a genuine Triangle Tube PSRKIT15 part.

Odstraňování problémů

If your boiler is experiencing ignition problems, the igniter may be a contributing factor. Always consult a qualified technician for diagnosis and repair.

Always consult the comprehensive troubleshooting guide in your specific Triangle Tube boiler manual for detailed diagnostic procedures.

Specifikace

Záruka a podpora

For specific warranty information regarding the PSRKIT15 Prestige Igniter with Gasket, please refer to the documentation provided with your original boiler purchase or contact Triangle Tube directly. Warranty terms typically cover manufacturing defects.

For technical support, service, or to purchase genuine replacement parts, please contact an authorized Triangle Tube dealer or service provider. Always ensure that replacement parts are genuine to maintain boiler performance and safety.

Triangle Tube Official Webmísto: www.triangletube.com