1. Konec produktuview
The Sicce Ultrazero Flat Sucking Pump is designed for efficient removal of water from various areas, including flooded cellars, garages, and other spaces where minimal residual water is desired. This submersible pump is capable of reducing water levels down to 2-3 mm.
Klíčové vlastnosti:
- Capable of pumping water down to 2 mm residual level.
- Fully submersible design.
- Handles dirt particles up to 3 mm in size.
- Equipped with a 10-meter power cable.
- Features a practical carry handle for easy transport.
Obrázek 1: Přesview of the Sicce Ultrazero Flat Sucking Pump.
2. Bezpečnostní informace
Read all safety warnings and instructions before operating the pump. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Always disconnect the pump from the power supply before handling, cleaning, or performing any maintenance.
- Zajistěte napájení objtage matches the pump's specifications (230 V/50 Hz).
- Do not operate the pump with a damaged power cord or plug. If damaged, it must be replaced by the manufacturer, service agent, or similarly qualified persons to avoid a hazard.
- Do not use the pump to handle flammable or explosive liquids.
- Udržujte děti a neoprávněné osoby mimo provozní prostor.
- Během provozu se ujistěte, že je čerpadlo zcela ponořené, aby se zabránilo přehřátí.
- Avoid running the pump dry for extended periods.
- This pump is designed for water only. Do not use it for other liquids without consulting the manufacturer.
3. Nastavení a instalace
Follow these steps to properly set up your Ultrazero pump:
- Vybalte čerpadlo: Opatrně vyjměte čerpadlo a veškeré příslušenství z obalu. Zkontrolujte, zda není poškozeno.
- Connect the Discharge Hose:
The pump features a 26.44 mm (3/4") AG pressure connection. Attach a suitable discharge hose (e.g., 20 mm (3/4") hose connection) to this outlet. Ensure the connection is secure to prevent leaks.
Figure 2: Close-up of the pump's discharge outlet and integrated carry handle.
- Umístěte čerpadlo: Place the pump directly on the surface from which water needs to be removed. Ensure the pump is stable and upright. The flat base allows for efficient water removal down to minimal levels.
- Route the Discharge Hose: Direct the discharge hose to a suitable drainage area, ensuring the water will not flow back into the area being drained.
- Připojení napájení: Plug the 10-meter power cable into a grounded 230 V/50 Hz electrical outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety, especially in wet environments.
Figure 3: The flat base of the pump designed for low residual water levels.
4. Návod k obsluze
The Ultrazero pump is designed for simple operation:
- Ponořte čerpadlo: Ensure the pump is fully submerged in the water you wish to remove. The pump requires water to cool its motor and operate correctly.
- Začněte čerpat: Once submerged and connected to power, the pump will begin operating automatically. It does not feature a float switch, so manual monitoring is required for optimal use.
- Monitorování hladiny vody: The pump will continue to operate until the water level reaches its minimum suction capability of 2-3 mm.
- Zastavte pumpování: To stop the pump, disconnect it from the power supply. It is recommended to disconnect the pump once the desired water level is reached or if the pump starts to run dry.
Figure 4: The Ultrazero pump effectively draining water from a small pool.
Figure 5: The pump in action on a flooded floor, demonstrating its low-level suction capability.
Figure 6: Illustration of the pump's ability to reduce water levels to approximately 2 mm.
5. Údržba
Pravidelná údržba zajišťuje dlouhou životnost a optimální výkon vašeho čerpadla.
- Čištění: After each use, especially when pumping dirty water, rinse the pump thoroughly with clean water. This helps prevent sediment buildup.
- Prohlédněte si trosky: Periodically check the pump's intake area for any debris (e.g., leaves, small stones) that might obstruct water flow. Remove any blockages carefully after disconnecting power.
- Kontrola kabelů: Regularly inspect the power cable for cuts, abrasions, or other damage. Do not use the pump if the cable is damaged.
- Skladování: When not in use, store the pump in a clean, dry place, protected from frost.
Figure 7: The pump can also be used for transferring water for tasks like garden watering from a rain barrel.
6. Řešení problémů
If you encounter issues with your Ultrazero pump, refer to the following common problems and solutions:
| Problém | Možná příčina | Řešení |
|---|---|---|
| Čerpadlo se nespustí. | Žádné napájení. Poškozený napájecí kabel. Aktivována ochrana motoru proti přetížení. | Zkontrolujte připojení napájení a zásuvku. Inspect cable for damage; replace if necessary (by qualified personnel). Disconnect power, allow motor to cool, then reconnect. |
| Čerpadlo běží, ale voda se nevypouští. | Intake blocked. Discharge hose kinked or blocked. Airlock in pump. | Disconnect power, clear intake. Check and clear discharge hose. Briefly lift and lower the pump while submerged to release trapped air. |
| Reduced pumping performance. | Částečná blokáda. Impeller worn. | Disconnect power, clean pump intake and impeller area. Pro servis kontaktujte zákaznickou podporu. |
| Čerpadlo se neočekávaně zastaví. | Overheating due to low water level or blockage. Elektrická závada. | Disconnect power, check water level and clear blockages. Allow to cool. Pokud problém přetrvává, kontaktujte zákaznickou podporu. |
If the problem persists after attempting these solutions, please contact Sicce customer support.
7. Technické specifikace
Detailed specifications for the Sicce Ultrazero Flat Sucking Pump, Model 925607:
| Specifikace | Hodnota |
|---|---|
| Značka | Sicce |
| Číslo modelu | 925607 |
| Max. Delivery Rate (Flow Rate) | 3000 l/h |
| Max. Výška dodávky | 3.1 m |
| Power Consumption (P1) | 80 W |
| Provozní svtage | 220-240 V / 50 Hz |
| Conductor Length (Power Cable) | 10 m (three-core, indoor and outdoor use) |
| Tlakové připojení | 26.44 mm (3/4") AG |
| Průměr hadicové přípojky | 20 mm (3/4") |
| Max. Solids Size | 3 mm |
| Hladina zbytkové vody | Down to 2-3 mm |
| Rozměry produktu (přibližně) | 140 mm (Diameter) x 160 mm (Height) / 5.5" x 6.3" |
| Hmotnost položky | 2.6 kg (5.72 lb) |
| Plovákový spínač | Žádný |
| Ochrana proti přetížení | No (Internal thermal protection may exist, but no external reset) |
| Původ | Vyrobeno v Itálii |
Figure 8: Technical drawing illustrating the pump's dimensions and 3/4" GAS connection.
8. Záruka a podpora
For warranty information or technical support regarding your Sicce Ultrazero Flat Sucking Pump, please contact Sicce customer service. Keep your purchase receipt and model number (925607) handy when contacting support.
Výrobce: Ebara
Značka: Sicce
For further assistance, visit the official Sicce webstránky nebo se obraťte na svého místního distributora.
