Návod k obsluze dálkového ovladače a termostatu ke krbu SkyTech SKY-5301

1. Úvod

The SkyTech SKY-5301 remote control system provides a safe, reliable, and user-friendly method for operating gas heating appliances. This system allows for both thermostatic and manual control directly from the handheld transmitter. It operates using radio frequencies (RF) within a 20-foot range, utilizing non-directional signals. The system is pre-programmed with one of 1,048,567 security codes at the factory. For initial use, the remote receiver's code must be matched to the transmitter's code.

2. Bezpečnostní informace

• Před instalací a provozem si pečlivě přečtěte všechny pokyny.
• This system is designed for use with millivolt gas valves only. The receiver acts as a dry contact switch and will not output any voltage.
• Zajistěte, aby veškeré zapojení prováděl kvalifikovaný technik a aby splňovalo místní předpisy.
• Do not expose the transmitter or receiver to water or extreme temperatures.
• Jakmile se zobrazí indikátor slabé baterie, ihned vyměňte baterie, aby byl zajištěn správný provoz.
• Uchovávejte mimo dosah dětí.

3. Obsah balení

Ověřte, zda jsou v balení přítomny všechny komponenty:

• Handheld Transmitter (with LCD display)
• Receiver Box (wall plate mounted)
• Wall Plate (for receiver mounting)
• Pokyny k instalaci
• Batteries (4 AA batteries for transmitter and receiver)

4. Komponenty přesview

The SkyTech SKY-5301 system consists of a handheld transmitter and a wall-mounted receiver unit. Understanding each component is essential for proper setup and operation.

Obrázek 1: Nadview of the SkyTech SKY-5301 system, showing the handheld transmitter with its backlit LCD screen displaying temperature and time, and the wall-mounted receiver with its ON/REMOTE/OFF slider switch and LEARN button.

4.1. Handheld Transmitter

• LCD displej: Shows room temperature, set temperature, 24-hour clock, and a 9-hour countdown timer. Features a backlight for visibility.
• tlačítka: Three buttons (Up, Mode, Down) for navigation and setting adjustments.
• Funkčnost: Allows for manual or thermostatic control of the fireplace.

4.2. Wall-Mounted Receiver

• Posuvný přepínač: Features ON, REMOTE, and OFF positions for direct control or remote operation.
• Tlačítko LEARN: Used to synchronize the receiver with the transmitter.
• Moc: Battery-powered for reliable operation.
• Kompatibilita: Designed exclusively for millivolt gas valves, acting as a dry contact switch. It does not output voltage.

5. Nastavení

5.1. Instalace baterie

Install the included AA batteries into both the transmitter and the receiver unit.

1. Vysílač: Open the battery compartment on the back of the handheld transmitter. Insert the batteries, observing the correct polarity (+/-). Close the compartment.
2. Přijímač: Remove the wall plate cover. Open the battery compartment on the receiver unit. Insert the batteries, observing the correct polarity (+/-). Close the compartment.

5.2. Zapojení přijímače

The receiver unit must be wired to your fireplace's millivolt gas valve. This process typically involves connecting two wires from the receiver to the appropriate terminals on the gas valve. Ensure the fireplace's gas supply is turned OFF before proceeding with any wiring.

1. Locate the millivolt gas valve on your fireplace.
2. Identify the two terminals designated for remote control or thermostat connection. These are typically labeled TH and TH/TP or similar.
3. Connect the two wires from the receiver unit to these terminals. The polarity of these wires usually does not matter for a dry contact switch.
4. Zajistěte připojení.

5.3. Montáž přijímače

After wiring, mount the receiver unit to the wall using the provided wall plate and hardware. Ensure it is in a location where it can receive signals from the transmitter, ideally within 20 feet and not obstructed by large metal objects.

5.4. Pairing the Transmitter and Receiver (Learning Function)

The transmitter and receiver must be paired to communicate. This process is called the "learning function."

1. Ensure batteries are installed in both units.
2. On the receiver unit, slide the ON/REMOTE/OFF switch to the VZDÁLENÝ pozice.
3. Stiskněte a podržte UČIT SE button on the receiver for approximately 3 seconds until you hear a short beep.
4. Within 20 seconds of the beep, press any button on the handheld transmitter.
5. The receiver will emit a series of beeps, confirming that the transmitter and receiver are now paired.
6. Test the connection by pressing the "Up" or "Down" button on the transmitter to see if the fireplace responds.

6. Provoz

6.1. Transmitter Display and Controls

The backlit LCD on the transmitter provides essential information and allows for easy control.

• Informace o displeji:
  • Aktuální pokojová teplota
  • Nastavte teplotu
  • 24hodinové hodiny
  • 9hodinový odpočítávací časovač
  • Indikátor stavu baterie
• tlačítka:
  • NAHORU (▲): Increases set temperature, adjusts time/timer up.
  • MODE/SET: Cycles through operating modes, enters setting menus.
  • DOLŮ (▼): Decreases set temperature, adjusts time/timer down.

6.2. Provozní režimy

The system supports two primary operating modes:

• Manuální režim: The fireplace turns ON or OFF directly when commanded by the transmitter, regardless of temperature.
• Termostatický režim: The fireplace will turn ON or OFF automatically to maintain the set temperature.

6.3. Nastavení teploty

1. Stiskněte tlačítko MODE/SET button until the display shows the desired operating mode (e.g., "THERMO").
2. Použijte NAHORU (▲) or DOLŮ (▼) buttons to adjust the set temperature to your desired level. The display will show the set temperature.
3. The system will automatically maintain this temperature in thermostatic mode.

6.4. Nastavení časovače

The 9-hour countdown timer can be used to automatically turn off the fireplace after a set duration.

1. Stiskněte tlačítko MODE/SET button until the display shows "TIMER".
2. Použijte NAHORU (▲) or DOLŮ (▼) buttons to set the desired countdown duration (up to 9 hours).
3. Once set, the timer will begin counting down. The fireplace will turn off when the timer reaches zero.

7. Údržba

7.1. Výměna baterie

When the low battery indicator appears on the transmitter's LCD, or if the system becomes unresponsive, replace the batteries in both the transmitter and receiver with fresh AA batteries. Always replace all batteries at the same time.

7.2. Čištění

Wipe the transmitter and receiver surfaces with a soft, dry cloth. Do not use abrasive cleaners or immerse the units in water.

8. Řešení problémů

9. Specifikace

10. Záruka a podpora

For warranty information or technical support, please refer to the contact details provided with your product packaging or visit the official SkyTech webmísto. Uschovejte si doklad o koupi pro případ záručních reklamací.