1. Úvod
The Watts WR-100 Water Filter Wrench is a specialized tool designed for the removal of water filter housings. It facilitates the loosening of the housing body from the cap, primarily for the purpose of replacing filter cartridges. This wrench is intended for use with residential and RV filter sumps.
Důležité: This wrench is designed for uvolnění filter housings only. Do NOT use this wrench to tighten the sump, as this can lead to overtightening and damage.
2. Nastavení
Before attempting to change a water filter, ensure the following:
- Vypněte přívod vody do filtračního systému.
- Relieve any pressure in the system by opening a nearby faucet or using a pressure relief button on the filter housing, if available.
- Have a bucket or towels ready to catch any spilled water during the filter change process.
- Ensure you have the correct replacement filter cartridge.
3. Návod k obsluze
Follow these steps to use the Watts WR-100 Water Filter Wrench:
- Position the circular end of the WR-100 wrench over the filter housing sump.
- Slide the wrench down until it achieves a snug fit around the housing, engaging the teeth or ridges on the wrench with those on the housing.
- Apply firm, counter-clockwise pressure to the wrench handle to loosen the filter housing. The housing should begin to unscrew.
- Once loosened, you can typically unscrew the housing by hand.
- Remove the old filter cartridge and proceed with replacing it according to your filter system's specific instructions.
Figure 1: The Watts WR-100 Water Filter Wrench. This image shows the Watts WR-100 Water Filter Wrench, a white plastic tool designed for removing water filter housings. The circular end is used to grip the filter sump.
4. Údržba
The Watts WR-100 Water Filter Wrench requires minimal maintenance:
- After use, wipe the wrench clean with a damp cloth to remove any water or debris.
- Store the wrench in a dry place, away from direct sunlight or extreme temperatures, to prevent material degradation.
- Inspect the wrench periodically for any signs of cracks or damage. If damaged, replace the wrench to ensure safe and effective operation.
5. Řešení problémů
- Wrench does not fit the housing: Ensure the wrench is compatible with your specific filter housing model. The WR-100 is designed for Watts residential/RV housings. Some older or non-Watts housings may have different dimensions.
- Housing is too tight to loosen:
- Verify that the water supply is completely off and pressure has been relieved.
- Apply steady, firm pressure. Avoid sudden jerking motions.
- If the housing is extremely tight, ensure the wrench is fully engaged. In some cases, a second person might be needed to stabilize the filter system while the wrench is turned.
- Wrench slips: Ensure the wrench is properly seated and snug against the housing. The housing and wrench should be dry to maximize grip.
6. Specifikace
| Číslo modelu | WR-100 |
| Značka | Watts |
| Barva | Bílý |
| Materiál | Plast |
| Délka položky | Přibližně 10 palce |
| Hmotnost položky | Přibližně 2.08 unce (0.13 libry) |
| Styl hlavy | Kolo |
| Provozní režim | Mechanické |
7. Informace o záruce
Warranty information for the Watts WR-100 Water Filter Wrench is not explicitly provided in the product details. For specific warranty inquiries, please contact Watts customer support directly.
8. Podpora
For further assistance, technical support, or questions regarding the Watts WR-100 Water Filter Wrench, please refer to the official Watts webstránky nebo kontaktujte jejich oddělení zákaznických služeb. Kontaktní informace obvykle naleznete na obalu výrobce nebo webmísto.
Můžete také navštívit Watts Store on Amazon pro další informace o produktu.
