Grafický ekvalizér Pyramid 906 s 10 pásmovým zesilovačem výkonu Amplifier Uživatelská příručka

1. Úvod

Děkuji za nákupasing the Pyramid 906 10-Band Power Booster Graphic Equalizer Amplifier. This unit is designed to enhance your car audio system by providing precise control over audio frequencies and boosting the overall power output. To ensure optimal performance and safe operation, please read this manual thoroughly before installation and use. Keep this manual for future reference.

This image displays the front panel of the Pyramid 906 equalizer amplifier, showing the power knob, various control buttons, and the 10-band graphic equalizer sliders with their protective cover open.

2. Nastavení a instalace

2.1 Bezpečnostní opatření

• Před zahájením jakýchkoli elektrických prací odpojte záporný pól baterie vozidla.
• Ujistěte se, že veškeré vedení je řádně izolováno, aby se zabránilo zkratu.
• Mount the unit securely to avoid movement during vehicle operation.
• Avoid installing the unit in areas exposed to direct sunlight, excessive heat, moisture, or dust.
• Use appropriate gauge wiring for power and ground connections.

2.2 Co je v krabici

Ověřte, zda jsou součástí vašeho nákupu následující položky:

• Pyramid 906 Equalizer Ampdoživotní
• Montážní materiál (šrouby, konzoly)
• Uživatelská příručka

2.3 Zapojení kabeláže

Proper wiring is crucial for performance and safety. Refer to the following general guidelines:

1. Výkon (B+): Connect the +12V terminal to the vehicle's positive battery terminal using a fused power cable. The fuse should be located within 18 inches of the battery.
2. Zem (GND): Connect the GND terminal to a clean, unpainted metal surface of the vehicle chassis. Ensure a solid electrical connection.
3. Dálkové ovládání (REM): Connect the REM terminal to the remote turn-on output of your car stereo. This will turn the equalizer on and off with your stereo.
4. Zvukový vstup: Connect the audio output from your car stereo (RCA cables) to the input jacks of the equalizer.
5. Zvukový výstup: Connect the audio output from the equalizer (RCA cables) to the input of your amplifikátor(y).

2.4 Montáž

Choose a suitable location for mounting the equalizer, such as under the dashboard, in the glove compartment, or under a seat. Ensure adequate ventilation around the unit. Use the provided mounting hardware to secure the unit firmly.

3. Návod k obsluze

3.1 Ovládací prvky na předním panelu

Familiarize yourself with the controls on the front panel:

• POWER Knob: This knob controls the overall power to the unit and may also function as a master volume or gain control. Rotate clockwise to turn on and increase level, counter-clockwise to decrease and turn off.
• LEVEL Switch: Adjusts the input sensitivity or output level of the unit.
• Tlačítko SCAN: Used for scanning radio frequencies if the unit has an integrated tuner function.
• Tlačítko HOLD: Used to hold a specific radio frequency or setting during scan.
• ANT Switch: Controls the antenna function, possibly for an integrated tuner or to activate a power antenna.
• FADER Knob: Adjusts the balance between front and rear speakers.
• Graphic Equalizer Sliders: Ten individual sliders allow for precise adjustment of specific audio frequency bands.

3.2 Nastavení ekvalizéru

The 10-band graphic equalizer allows you to fine-tune the audio response of your system:

1. Identify Frequency Bands: Each slider corresponds to a specific frequency (e.g., 30Hz, 60Hz, 120Hz, 250Hz, 500Hz, 1kHz, 2kHz, 4kHz, 8kHz, 16kHz).
2. Úprava posuvníků: Move a slider up to boost that frequency band or down to cut it.
3. Bass Frequencies (Low End): Adjust the lower frequency sliders (e.g., 30Hz-120Hz) to control the depth and impact of bass.
4. Mid-Range Frequencies: Adjust the middle frequency sliders (e.g., 250Hz-2kHz) to control vocals and instruments.
5. Treble Frequencies (High End): Adjust the higher frequency sliders (e.g., 4kHz-16kHz) to control the brightness and clarity of high notes.
6. Listen and Refine: Make small adjustments and listen carefully to the changes. Aim for a balanced sound that suits your preferences and vehicle acoustics.

3.3 Power Booster Function

The integrated power booster amplifies the audio signal, providing increased volume and dynamic range to your speakers. Ensure your speakers are rated to handle the output power of this unit to prevent damage.

4. Údržba

4.1 Čištění

To maintain the appearance and functionality of your equalizer:

• Vnější povrch otřete měkkým suchým hadříkem.
• Na odolné nečistoty použijte mírně damp hadříkem s jemným čisticím prostředkem a poté otřete dosucha.
• Nepoužívejte agresivní chemikálie, rozpouštědla ani abrazivní čisticí prostředky.

4.2 Obecná péče

Regularly check all wiring connections to ensure they are secure and free from corrosion. Avoid placing heavy objects on the unit or obstructing its ventilation openings.

5. Řešení problémů

If you encounter issues with your Pyramid 906, refer to the following common problems and solutions:

6. Specifikace

The following specifications apply to the Pyramid 906 10-Band Power Booster Graphic Equalizer Ampživější:

• Maximální výstupní výkon: 150 wattů x 2
• Materiál: Hliník, akryl
• Nominální impedance: 8 ohm (Note: This specification typically refers to speaker impedance. For this equalizer, it may relate to internal component characteristics.)
• Počet položek: 1
• Počet jednotek: 1.0 Počet

7. Záruka a podpora

Pyramid products are designed for reliability and performance. This product is covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Pyramid webmísto.

For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Pyramid customer service. Contact information can typically be found on the product packaging or the official Pyramid webmísto.