Návod k obsluze elektronického nástěnného odpočítávacího časovače Intermatic EI210 10/20/30/60 minut

Zavedení

This manual provides detailed instructions for the installation, operation, and maintenance of your Intermatic EI210 Electronic in-Wall Countdown Timer. Please read these instructions carefully before installation and use to ensure proper functionality and safety.

Klíčové vlastnosti:

• Jednoduchá obsluha: Easily select countdown times of 10, 20, 30, or 60 minutes with the push of a single button—no programming needed.
• Univerzální kompatibilita: Replaces single-pole switches, compatible with a range of Intermatic products.
• Tichý provoz: Operates without mechanical noise.
• Snadná instalace: Straightforward setup.
• Slonovinová povrchová úprava: Blends seamlessly with your decor.

Důležité bezpečnostní informace

WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND TEST THAT POWER IS OFF BEFORE WIRING.

• Toto zařízení je určeno pouze pro vnitřní použití.
• Ujistěte se, že všechny kabelové spoje jsou bezpečné.
• Pokud si nejste jisti některou částí instalace, poraďte se s kvalifikovaným elektrikářem.

Pokyny k instalaci

Follow these steps for proper installation of your EI210 timer:

1. Vypnout napájení: Remove the wall plate and disconnect the existing light switch. Ensure power is OFF at the circuit breaker and verify with a tester before proceeding.
2. Zkontrolujte zapojení: Confirm that both "hot" and neutral wires are present in the junction box. If neutral wires are not present, additional wiring may be required.
3. Connect Timer Wires:
   • Připojte červený timer wire to the wire leading to the fixture (load) using a wire connector.
   • Připojte černý timer wire to the incoming "hot" (usually black or red) wire from the power source in the junction box using a wire connector.
   • Odřízněte bílý wire in the junction box (or open splice) and strip 3/8" of insulation. Connect the bílý timer wire to the white (neutral) wires in the junction box using a wire connector.
   • If the wall switch you are replacing had separate grounding conductors connected to a GREEN screw, connect these to the zelený wire from the timer with a wire connector.
4. Zabezpečená připojení: Double-check that all wire connections are secure and properly insulated.
5. Namontujte časovač: Carefully place all wires inside the junction box. Fit the timer into the junction box and secure it using the two mounting screws provided.
6. Obnovit napájení: Reconnect electrical power at the circuit breaker.

Figure 1: Wiring Diagram for Intermatic EI210. This diagram illustrates the connection of the timer's neutral (white) and hot (black or red) wires within a standard junction box.

Figure 2: Detailed Wiring Diagram. This diagram shows the connections for hot, ground, and white wires, ensuring proper electrical setup for the timer.

Návod k obsluze

Intermatic EI210 Timer Faceplate. This image displays the timer's front panel with buttons for 10, 20, 30, 60 minutes, and a HOLD function.

Režim časovače

To activate the timer mode, press and release the push button (for less than 2 seconds) repeatedly. Each press will cycle through the available countdown settings: 10, 20, 30, or 60 minutes. An illuminated LED next to the selected time indicates the current setting, and the connected load will turn ON. The timer will begin counting down, and once the selected time has elapsed, all 5 LEDs will turn off, and the connected load will turn OFF.

Režim Hold (nepřetržitý provoz)

To keep the connected load ON for an indefinite period, press and hold the push button for more than 2 seconds. The timer will enter HOLD mode, indicated by the HOLD LED illuminating. The connected load will remain ON continuously. To exit HOLD mode, press and release the push button. All 5 LEDs will turn off, and the connected load will also turn OFF.

Údržba

The Intermatic EI210 timer is designed for maintenance-free operation. To clean the surface, use a soft, damp cloth. Avoid using abrasive cleaners or solvents, as these may damage the finish or internal components.

Odstraňování problémů

If your Intermatic EI210 timer is not functioning as expected, consider the following:

• Bez napájení: Ensure the circuit breaker supplying power to the timer is ON. Verify all wiring connections are secure as per the installation instructions.
• Load Not Turning On/Off: Check if the timer is in the correct mode (Timer Mode or Hold Mode). If in Timer Mode, ensure a countdown time is selected. If in Hold Mode, ensure the HOLD LED is illuminated.
• Nekonzistentní provoz: Re-verify wiring connections. Ensure the timer is not exposed to extreme temperatures or moisture.

If issues persist, contact Intermatic customer support for further assistance.

Specifikace

Informace o záruce

This Intermatic product comes with a 1-letá záruka. This warranty covers replacement of the unit but does not include labor costs. For warranty claims or further details, please contact Intermatic customer support.

Zákaznická podpora

For technical assistance, troubleshooting, or warranty inquiries, please visit the official Intermatic webnebo kontaktujte jejich oddělení zákaznických služeb. Kontaktní informace obvykle naleznete na obalu produktu nebo na webových stránkách výrobce. webmísto.

Konec produktuview Video