1. Úvod
This manual provides important information for the safe and proper operation, maintenance, and troubleshooting of your Einhell BT-TJ 2250 Trolley Jack. Please read this manual thoroughly before using the product and keep it for future reference.
The Einhell BT-TJ 2250 is a robust and stable trolley jack designed for lifting vehicles with a maximum load capacity of 2250 kg. It features two ball-bearing swivel castors for easy maneuverability, an extra-large support saddle, and a long, two-part lifting rod to ensure safe and easy lifting of loads. An integrated safety valve protects against overloading.
2. Bezpečnostní pokyny
Vždy dodržujte následující bezpečnostní opatření, abyste předešli zranění nebo poškození produktu:
- Přečtěte si manuál: Before operation, read and understand all instructions and warnings in this manual.
- Kapacita zatížení: Nikdy nepřekračujte maximální nosnost 2250 kg.
- Stabilní povrch: Always use the jack on a hard, level, and stable surface.
- Podpora vozidel: After lifting, always support the vehicle with appropriate jack stands before working underneath it. Never rely solely on the jack for support.
- Center Load: Ensure the load is centered on the saddle of the jack.
- Vyčistit oblast: Keep hands, feet, and other body parts clear of moving parts and the area under the load.
- Údržba: Regularly inspect the jack for damage or wear. Do not use if damaged.
- Děti a domácí mazlíčci: Udržujte děti a domácí zvířata mimo pracovní oblast.
- Ochrana proti přetížení: The jack is equipped with an overload safety valve. Do not attempt to bypass or adjust this valve.
3. Komponenty produktu
Familiarize yourself with the parts of your Einhell BT-TJ 2250 Trolley Jack:
- Hlavní tělo: The robust steel frame of the jack.
- Zvedací rameno: The movable arm that raises the support saddle.
- Support Saddle: The circular pad at the top of the lifting arm where the load rests. It is extra-large for stability.
- Swivel Castors: Two ball-bearing wheels at the rear for easy steering and positioning.
- Fixed Wheels: Two wheels at the front for stability.
- Lifting Rod (Handle): A two-part rod used to pump the jack and operate the release valve.
- Vypouštěcí ventil: Located at the base of the lifting mechanism, controlled by rotating the lifting rod.
- Overload Safety Valve: Internal mechanism to prevent lifting beyond the rated capacity.
4. Nastavení a montáž
The Einhell BT-TJ 2250 Trolley Jack typically comes pre-assembled, but the lifting rod may need to be attached.
- Attach the Lifting Rod: Insert the two parts of the lifting rod together. Then, insert the assembled rod into the handle socket on the jack. Ensure it is securely seated.
- Bleed Air (First Use): Before first use, it is recommended to bleed any air from the hydraulic system.
- Turn the lifting rod counter-clockwise to fully open the release valve.
- Pump the lifting rod vigorously several times.
- Turn the lifting rod clockwise to close the release valve.
5. Návod k obsluze
5.1. Zvedání břemene
- Připravte vozidlo: Park the vehicle on a hard, level surface. Engage the parking brake and block the wheels that will remain on the ground.
- Umístění zvedáku: Locate the vehicle's designated lifting points (refer to your vehicle's owner's manual). Position the jack's support saddle directly under the lifting point.
- Zavřete vypouštěcí ventil: Turn the lifting rod clockwise until the release valve is fully closed. Do not overtighten.
- Zvedněte břemeno: Pump the lifting rod up and down to raise the support saddle and lift the vehicle. Continue pumping until the vehicle reaches the desired height.
- Zajištění pomocí zvedáků: Immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by carefully turning the lifting rod counter-clockwise. Once the vehicle is securely resting on the jack stands, remove the trolley jack.
5.2. Spouštění břemene
If the vehicle is on jack stands, first lift it slightly off the stands using the trolley jack before lowering.
- Vyčistěte oblast: Ensure no one is under or near the vehicle.
- Umístění zvedáku: If removed, reposition the jack's support saddle under the lifting point.
- Pomalu otevírejte vypouštěcí ventil: Slowly and carefully turn the lifting rod counter-clockwise to open the release valve. The vehicle will begin to descend. Control the descent speed by adjusting how much you open the valve.
- Úplně dolů: Continue lowering until the vehicle is fully on the ground.
- Odstraňte Jacka: Once the vehicle is stable on the ground, remove the trolley jack.
6. Údržba a skladování
- Čištění: Clean the jack regularly with a damp tkanina. Nepoužívejte agresivní chemikálie.
- Mazání: Periodically lubricate moving parts and pivot points with light machine oil.
- Hydraulický olej: Check the hydraulic oil level periodically. If low, refill with a high-quality hydraulic jack oil. Consult a qualified technician if unsure.
- Inspekce: Před každým použitím zkontrolujte zvedák, zda nevykazuje známky poškození, netěsností nebo opotřebení. Poškozený zvedák nepoužívejte.
- Skladování: Store the jack in a dry, clean place, preferably with the ram fully retracted to protect the hydraulic cylinder.
7. Řešení problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Jack does not lift or lifts slowly. | Low hydraulic oil level; Air in the system; Release valve not fully closed; Overload. | Check and refill hydraulic oil; Bleed air from the system (see Setup); Ensure release valve is fully closed; Do not exceed load capacity. |
| Zvedák se pod zátěží spustí dolů. | Release valve not fully closed; Internal leak; Damaged seals. | Ensure release valve is fully closed; Consult a qualified technician for repair or replacement of seals. |
| Jack vydává neobvyklé zvuky. | Air in the system; Lack of lubrication; Damaged components. | Bleed air from the system; Lubricate moving parts; Inspect for damage and replace if necessary. |
8. Specifikace
| Funkce | Detail |
|---|---|
| Značka | Einhell |
| Číslo modelu | 2022135 |
| Kapacita zatížení | 2250 kg |
| Minimální výška | 140 mm |
| Maximální výška | 495 mm |
| Hmotnost položky | 32 kg |
| Rozměry (balení) | 74 x 35.8 x 23.6 cm |
9. Záruka a podpora
Informace o záruce naleznete v záručním listu, který je součástí vašeho produktu, nebo navštivte oficiální webové stránky společnosti Einhell. website. For technical support or spare parts, please contact Einhell customer service. Keep your purchase receipt as proof of purchase.
Einhell Customer Service: Please refer to the contact details provided on the Einhell official webna webu nebo v obalu vašeho produktu.
