Dimplex XT9605 Charge Control Thermostat User Manual

1. Úvod

This manual provides essential information for the safe and effective installation, operation, and maintenance of your Dimplex XT9605 Charge Control Thermostat. This thermostat is specifically designed as a replacement for older, larger thermostats found in Dimplex XL storage heaters manufactured before October 2001. Please read these instructions thoroughly before proceeding with any installation or operation.

1.1 Bezpečnostní informace

• Always disconnect the main power supply to the storage heater before attempting any installation, maintenance, or repair work. Failure to do so can result in electric shock or serious injury.
• Installation should only be performed by a qualified electrician or competent person.
• Ensure all connections are secure and comply with local wiring regulations.
• Nepoužívejte termostat, pokud se jeví poškozený.

2. Nastavení a instalace

The Dimplex XT9605 thermostat is designed for straightforward replacement of existing units. It comes with new fixings, which may have different thread types than your old thermostat. Exercise caution and do not force connections.

2.1 Příprava

1. Odpojit napájení: Locate the main power switch for your Dimplex XL storage heater and turn it OFF. Verify that the power is off using a suitable voltage tester.
2. Přístup k termostatu: Opatrně odstraňte vnější krytkuasing or access panel of your storage heater to expose the existing thermostat. Refer to your specific heater's manual for detailed access instructions.

2.2 Postup výměny

1. Odstraňte starý termostat: Disconnect the wiring from the old thermostat, noting the position of each wire. It is recommended to take a photograph before disconnecting. Unscrew and remove the old thermostat.
2. Instalace nového termostatu: Position the new Dimplex XT9605 thermostat in the designated location. Use the provided new fixings to secure it. Ensure the thermostat is firmly mounted.
3. Připojení kabeláže: Reconnect the wiring to the new thermostat according to the previous configuration. Double-check all connections for tightness and correctness.

2.3 Závěrečné kroky

1. Znovu sestavte ohřívač: Replace the access panel or outer casing of the storage heater, ensuring all screws are tightened.
2. Obnovit napájení: Turn the main power supply to the storage heater back ON.
3. Testovací provoz: Proceed to the Operating section to test the thermostat's functionality.

3. Návod k obsluze

The Dimplex XT9605 thermostat controls the charge level of your Dimplex XL storage heater, influencing how much heat is stored during off-peak hours. The thermostat features a push-button type controller for setting adjustments.

3.1 Setting the Charge Level

The specific method for adjusting the charge level will depend on the design of your Dimplex XL heater's control panel, which interacts with this thermostat. Generally, you will find a dial or button on the heater's fascia that corresponds to the thermostat's setting. Consult your heater's user manual for precise instructions on how to adjust the charge control.

• A higher setting typically results in more heat stored, providing warmth for a longer duration.
• A lower setting results in less heat stored, which can save energy if less heat is required.

Allow time for the heater to cycle through a full charge period (usually overnight) to observe the effect of any adjustments.

4. Údržba

The Dimplex XT9605 Charge Control Thermostat is designed for reliable operation and requires minimal maintenance. Regular checks of the storage heater itself are recommended.

• Čištění: Ensure the area around the thermostat within the heater is free from dust and debris. Always disconnect power before cleaning.
• Vizuální kontrola: Periodically inspect the thermostat and its wiring for any signs of damage, loose connections, or overheating. If any issues are observed, disconnect power and consult a qualified technician.

5. Řešení problémů

If your Dimplex XL storage heater is not functioning as expected after thermostat replacement, consider the following:

• Žádné teplo/Nedostatečné teplo:
  • Napájení: Ensure the main power supply to the heater is ON.
  • Nastavení termostatu: Verify that the charge control setting on your heater is not set too low.
  • Zapojení: Double-check all wiring connections to the thermostat for correctness and tightness. Loose connections can prevent proper operation.
• Přehřívání:
  • Nastavení termostatu: Ensure the charge control setting is not excessively high for your heating needs.
  • Thermostat Fault: If the heater consistently overheats regardless of settings, the thermostat may be faulty and require replacement.
• Fyzické poškození: If the thermostat or its components appear physically damaged, it must be replaced.

For persistent issues, it is recommended to contact a qualified electrician or the manufacturer for assistance.

6. Specifikace

7. Záruka a podpora

Information regarding the specific warranty period for the Dimplex XT9605 Charge Control Thermostat was not provided. Please refer to your purchase documentation or contact the retailer from whom you purchased the product for warranty details.

For technical support or further assistance, please contact the manufacturer, Dimplex, or the authorized seller. Contact information can typically be found on the product packaging or the seller's webmísto.