Eaton CR20W-SP-L Commercial Grade Duplex Receptacle Instruction Manual

Zavedení

This manual provides essential instructions for the safe installation, operation, and maintenance of the Eaton CR20W-SP-L Commercial Grade Straight Blade Duplex Receptacle. Please read this manual thoroughly before beginning any installation or use to ensure proper function and safety.

Bezpečnostní informace

VAROVÁNÍ: Nebezpečí úrazu elektrickým proudem. Improper installation or use of this product can result in serious injury or death. Always adhere to the following safety guidelines:

• Installation must be performed by a qualified electrician in accordance with all national and local electrical codes and regulations.
• Always turn off power at the circuit breaker or fuse box before installing, servicing, or removing the receptacle. Verify power is off using a voltage tester.
• Do not install or use this product if it appears damaged.
• Ujistěte se, že všechna vodičová spojení jsou bezpečná a řádně izolovaná.
• Do not exceed the specified electrical ratings (20 Amp, 125 Volt).

Obsah balení

Před zahájením instalace ověřte, zda jsou všechny komponenty přítomny:

• One (1) Eaton CR20W-SP-L Commercial Grade Straight Blade Duplex Receptacle (White)

Note: Wallplate and mounting screws for the wallplate are typically sold separately.

Nastavení a instalace

Follow these steps carefully to install your Eaton CR20W-SP-L duplex receptacle:

1. Vypnout napájení: Locate the circuit breaker or fuse that controls the power to the outlet box where you intend to install the receptacle. Turn off the power completely. Use a voltage tester to confirm that the power is off at the outlet box.
2. Remove Old Receptacle (if applicable): Carefully unscrew and remove the existing receptacle from the wall box. Disconnect the wires from the old receptacle, noting which wire was connected to which terminal (typically black to brass, white to silver, bare/green to green).
3. Připravte dráty: If necessary, strip approximately 1/2 inch (12mm) of insulation from the ends of the electrical wires (hot, neutral, ground) in the wall box. Ensure the wire ends are clean and straight.
4. Připojit dráty: The Eaton CR20W-SP-L utilizes a side-wire method for secure connections. Form a hook at the end of each wire and wrap it clockwise around the appropriate terminal screw. Tighten the screws firmly to ensure good electrical contact.
   • Připojte žhavý (černý) drát k brass-colored terminal screw.
   • Připojte neutrální (bílý) vodič k silver-colored terminal screw.
   • Připojte ground (bare copper or green) wire k green terminal screw.

   Ensure no bare wire is exposed beyond the terminal screws and that wires are not pinched.

5. Montážní zásuvka: Carefully fold the connected wires into the electrical box. Insert the new receptacle into the box and secure it using the provided mounting screws. Do not overtighten.
6. Instalace nástěnné desky: Attach the decorative wallplate (not included) over the receptacle, securing it with its own screws.
7. Obnovit napájení: Turn the power back on at the circuit breaker or fuse box. Test the receptacle with a known working device to ensure proper functionality.

This image shows the Eaton CR20W-SP-L duplex receptacle in white, illustrating its robust design and the side-wire terminals for electrical connections. The front face features two standard 5-20R NEMA outlets.

Návod k obsluze

The Eaton CR20W-SP-L is a standard duplex receptacle designed for general electrical loads up to 20 Amperes and 125 Volts. To operate, simply insert the plug of your appliance or device firmly into one of the two available outlets. Ensure the plug is fully seated for a secure connection.

Údržba

The Eaton CR20W-SP-L receptacle requires minimal maintenance. Follow these guidelines:

• Pravidelná prohlídka: Regularly inspect the receptacle for any signs of physical damage, such as cracks, discoloration, or loose connections.
• Čištění: To clean the surface, wipe with a dry, soft cloth. Do not use liquid cleaners, solvents, or abrasive materials near electrical components. Ensure power is off before cleaning.
• Uvolněná připojení: If you notice any looseness in the receptacle or its connections, turn off power at the breaker and re-tighten all terminal screws. If the issue persists, consult a qualified electrician.

Odstraňování problémů

If you encounter issues with your Eaton CR20W-SP-L receptacle, consider the following:

No Power to Receptacle

• Check Circuit Breaker/Fuse: Verify that the circuit breaker for the circuit is not tripped or that the fuse is not blown. Reset the breaker or replace the fuse if necessary.
• Ověřte připojení: Ensure all wire connections within the receptacle and the electrical box are secure and properly made. Turn off power before checking connections.
• Test s jiným zařízením: Plug a different, known working device into the receptacle to confirm if the issue is with the receptacle or the original device.
• Poraďte se s elektrikářem: If the issue persists after performing these checks, there may be a more complex electrical problem. Contact a qualified electrician for further diagnosis and repair.

Specifikace

Záruka a podpora

For detailed warranty information, technical support, or to inquire about replacement parts, please contact Eaton customer service directly. You can find contact information and additional resources on the official Eaton webmísto: www.eaton.com.