Yamaha YT150 Guitar/Bass Auto Tuner Instruction Manual

Zavedení

The Yamaha YT150 is an auto tuner designed for both acoustic and electric guitars, as well as 4, 5, or 6-string bass guitars. It features a high-resolution LCD meter display for accurate tuning and LEDs for visibility in various lighting conditions. This manual provides instructions for the proper setup, operation, and maintenance of your YT150 tuner.

Obrázek 1: Yamaha YT150 Guitar/Bass Auto Tuner. This image shows the front view of the Yamaha YT150 tuner, displaying its LCD screen and control buttons.

Nastavení

1. Instalace baterie

The YT150 tuner requires one CR2 battery (included). To install or replace the battery:

1. Najděte přihrádku na baterie na zadní straně jednotky.
2. Otevřete kryt bateriového prostoru.
3. Vložte baterii CR2 a dbejte na správnou polaritu (+/-).
4. Bezpečně zavřete kryt bateriového prostoru.

2. Připojení nástroje

The YT150 offers two methods for connecting your instrument:

• For Electric Guitars/Basses: Connect your instrument to the tuner's VSTUP jack using a standard 1/4-inch instrument cable. If you wish to pass the signal through to an amplifier, connect the tuner's VÝSTUP jack do vašeho ampvstup od lifiera.
• For Acoustic Guitars: Utilize the built-in microphone. Ensure the tuner is placed near the soundhole of your acoustic instrument for optimal sound detection.

Návod k obsluze

1. Zapnutí/vypnutí

Locate the power switch, typically a slide switch, on the side or back of the unit. Slide it to the "ON" position to power on the tuner. Slide it to the "OFF" position when not in use to conserve battery life.

2. Selecting Tuning Mode

The YT150 features an auto mode and a dedicated bass mode:

• Automatický režim: This mode automatically detects the closest tone programmed in the tuner, providing fast and efficient tuning for both guitars and basses.
• Režim basů: For bass guitars, select the "bass mode" to display bass string notes in their proper order, optimizing the tuning experience for bass instruments.

3. Ladění nástroje

1. Zabrnkněte na jednu strunu na svém nástroji.
2. Observe the LCD display. The display will show the detected note.
3. Adjust your instrument's tuning peg until the display indicates the correct note and the "in-tune" LED illuminates. The sharp/flat LEDs will guide you if the note is too high or too low.
4. Opakujte pro všechny řetězce.

The large, easy-to-read liquid crystal display presents notes clearly, making tuning straightforward even from a distance or in low light conditions.

Údržba

1. Čištění

Wipe the tuner with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the finish and internal components.

2. Skladování

When not in use for extended periods, remove the battery to prevent leakage and store the tuner in a cool, dry place away from direct sunlight and extreme temperatures.

3. Výměna baterie

If the display becomes dim or the tuner behaves erratically, it may be time to replace the battery. Refer to the "Battery Installation" section under Setup for instructions.

Odstraňování problémů

• Tuner se nezapne:
  • Ujistěte se, že je vypínač v poloze „ON“.
  • Check the battery. Replace it if it is depleted or incorrectly installed.
• Nepřesné ladění:
  • Ensure the instrument is properly connected (via cable for electric, or microphone for acoustic).
  • For acoustic instruments, ensure the tuner's microphone is close to the sound source and there is minimal background noise.
  • Pluck strings firmly and clearly, one at a time.
  • Check if the correct mode (Auto or Bass) is selected for your instrument.
• Displej je slabý nebo bliká:
  • Baterie může být vybitá. Vyměňte baterii.

Specifikace

Záruka a podpora

Informace o záruce a zákaznické podpoře naleznete v dokumentaci dodané s vaším nákupem nebo navštivte oficiální webové stránky Yamaha. webUschovejte si doklad o koupi pro případné reklamace.

Online podpora: www.yamaha.com