1. Úvod
The Infineon DAS Programmer is a versatile tool designed for reading, writing, burning, and flashing Infineon automotive microcontrollers. It supports a wide range of TriCore, AURIX, XC16x, XC800, XC2000, XE166, XMC1000, and XMC4000 series chips, making it an essential device for automotive electronics development and repair.
2. Nastavení
2.1 Systémové požadavky
The DAS Programmer supports Windows 32/64 bit operating systems, including Windows XP, Windows 7, and Windows 10.
2.2 Obsah balení
Ověřte, zda jsou v balení přítomny všechny položky:
- 1 x DAP miniWiggler programmer unit
- 1 x 1.5-meter USB-B square port data cable
- 1 x 14P-2.54mm spacing cable
2.3 Hardwarové připojení
Connect the programmer to your target device using the provided 14P-2.54mm spacing cable. The read/write interface requires connection to 8 specific wires:
- VCC (Voltage Common Collector)
- GND (zem)
- TDI (Test Data In)
- TDO (Test Data Out)
- TCK (Test Clock)
- TMS (Test Mode Select)
- TRST (Test Reset)
- RESET (System Reset)
3. Návod k obsluze
Once the hardware is connected and the necessary drivers are installed on your Windows system, you can proceed with programming operations using the appropriate Infineon software (e.g., Memtool, DAS Device Scanner).
3.1 Software Interface Overview
The programming software provides an interface to select the target chip, load firmware files, and initiate read, write, or erase operations. Ensure the correct chip series is selected before proceeding.
3.2 Programming Steps (General)
- Connect the programmer to your computer via the USB cable.
- Connect the 14P cable from the programmer to the target microcontroller's JTAG/DAP interface.
- Launch the Infineon programming software (e.g., Memtool).
- Select the correct target device/chip model within the software.
- Nahrajte firmware file (.hex, .elf, etc.) you wish to program.
- Initiate the desired operation (e.g., 'Program', 'Erase', 'Verify', 'Read').
- Monitor the software's diagnostic log for status and completion messages.
4. Údržba
To ensure the longevity and reliable operation of your DAS Programmer, follow these maintenance guidelines:
- Udržujte zařízení čisté a bez prachu a nečistot. K čištění používejte měkký, suchý hadřík.
- Store the programmer in a cool, dry environment away from direct sunlight and extreme temperatures.
- Avoid exposing the device to moisture or corrosive substances.
- Handle cables and connectors with care to prevent damage to pins or internal wiring.
5. Řešení problémů
If you encounter issues with your DAS Programmer, consider the following common troubleshooting steps:
- Zařízení nebylo detekováno: Ensure the USB cable is securely connected to both the programmer and the computer. Verify that the necessary drivers are installed correctly for your operating system. Try a different USB port or cable.
- Chyby programování: Double-check the wiring connections to the target chip, especially the VCC, GND, and JTAG/DAP pins. Confirm that the correct chip model is selected in the programming software. Ensure the target chip is powered correctly.
- Problémy se softwarem: Restart the programming software and/or your computer. Ensure you are using the latest version of the Infineon programming tools.
- LED indikátory: Observe the 'RUN' and 'POWER' LEDs on the programmer. Refer to the software documentation for specific LED behavior interpretations.
6. Specifikace
| Funkce | Detail |
|---|---|
| Číslo modelu | TC17xx/2xx/3xx/TLE983x |
| Podporovaný OS | Windows 32/64 bit (WinXP/Win7/Win10) |
| Read/Write Interface | 8-wire (VCC, GND, TDI, TDO, TCK, TMS, TRST, RESET) |
| Původ | pevninská Čína |
| Supported TriCore Series | TC1724, 1728, TC1736, TC1766, TC1767, TC1782, TC1784, TC1796, TC1797, ... |
| Supported TriCore Aurix Series | TC21x, TC22x, TC23x, TC264/265/267, TC275/277, TC297/298/299, ... |
| Supported TriCore Aurix2G Series | TC32x, TC33x, TC35x, TC36x, TC37x, TC38x, TC39x |
| Supported XC16x Series | XC161, XC164, XC167 |
| Supported XC2000 Series | XC22xx, XC23xx, XC27xx |
| Supported XC800 Series | XC8xx |
| Supported XE166 Series | XE16x |
| Supported XMC Series | XMC1000/4000 series |
7. Uživatelské tipy
- Always ensure your programming environment (software and drivers) is up-to-date for optimal compatibility and performance.
- When connecting to a new target board, double-check the pin assignments to prevent damage to the programmer or the microcontroller.
- For critical programming tasks, perform a 'Read' operation first to back up the existing firmware if possible.
8. Záruka a podpora
For technical support, driver downloads, or warranty inquiries, please contact the seller or refer to the official Infineon documentation for the DAP miniWiggler. Keep your purchase records for any warranty claims.
9. Další zdroje
Toto video poskytuje přesview of the seller's operations and product range:
