1. Úvod
This manual provides comprehensive instructions for assembling, operating, and maintaining your Diymore DSO183 Digital Oscilloscope DIY Kit. Designed for electronics enthusiasts and educational purposes, this kit allows you to build a functional digital oscilloscope with a 500KHz bandwidth and integrated signal generator. Please read all instructions carefully before beginning assembly.
2. Vlastnosti produktu
- Návrh jednodeskové konstrukce: Compact integrated structure, convenient installation, high stability, suitable for a variety of experimental environments.
- Vestavěný generátor signálu: Integrates sine wave, triangle wave, and other waveform output functions to meet diversified testing needs.
- Ukládání a vyvolání průběhů: Supports waveform saving and quick call-out function, which is convenient for comparative analysis and repeated use.
- 500KHz high bandwidth: High-frequency response capability, accurately captures the details of complex signals.
- Ideal tool for electronic enthusiasts: Easy to operate, powerful, a powerful assistant for learning electronic technology and exploring the world of circuits.
3. Obsah balení
The DSO183 Digital Oscilloscope DIY Kit includes the following components:
- Main circuit board (SMD pre-soldered)
- Various resistors (e.g., 100K, 1.8M, 200K, 2M, 20K, 300Ω, 18Ω, 1.2K, 12Ω, 47Ω, 3K, 16K)
- Capacitors (e.g., 220pF, 100nF, 10nF, 1nF, 100pF, 10pF, 0.01uF)
- Diodes (e.g., 1N4148)
- BNC zásuvka
- Zásuvka USB Type-C
- Toggle switches (e.g., 2-position, 3-position)
- Tlačítka
- Potenciometry
- LED diody
- Acrylic panels (optional, to be purchased separately)
- USB power cord (included with some kits)
- BNC to alligator clip probe
- Assembly hardware (screws, nuts, standoffs)
4. Montážní návod
The DSO183 Digital Oscilloscope is provided as a DIY kit. The main circuit board has SMD components pre-soldered. You will need basic soldering skills and tools (soldering iron, solder, wire cutters, multimeter) to complete the assembly.
4.1. Identifikace a příprava komponent
- Rozbalte sadu: Carefully remove all components from their packaging.
- Identifikujte komponenty: Use the provided part list (if available) and a multimeter to identify and sort the resistors, capacitors, and other through-hole components. The video demonstrates using a multimeter to verify resistor values.
- Prepare components: Bend the leads of the components as needed to fit into the designated holes on the PCB.
4.2. Soldering Components
Follow the PCB markings and the circuit diagram (Figure 4.2) to correctly place and solder each component. Start with smaller components like resistors and diodes, then proceed to larger components like switches, sockets, and potentiometers.
- Insert the component leads into the correct holes on the PCB.
- Bend the leads slightly to hold the component in place.
- Solder each lead to its respective pad on the underside of the PCB.
- Trim any excess lead length using wire cutters after soldering.
4.3. Assembling the Enclosure (if applicable)
If your kit includes acrylic panels for an enclosure, follow these steps:
- Attach the front and rear panels to the oscilloscope board using the provided nylon posts and locking screws.
- Ensure all connections are secure and the board is properly aligned within the panels.
5. Základní obsluha
Once assembled, connect the DSO183 to a DC 5V power source via the USB Type-C interface. Use the provided BNC probe to connect to the circuit you wish to test.
5.1. Connectors, Switches, and Keys Overview
- Příkon: DC 5V via USB Type-C.
- Vstup signálu: BNC connector for oscilloscope probe.
- Coupling Switch (CPL): Selects DC, AC, or GND coupling. When set to GND, the input signal is disconnected, and the oscilloscope input is grounded (0V input).
- Sensitivity Switch 1 (SEN1) & 2 (SEN2): Adjusts the vertical sensitivity. The actual sensitivity value is displayed in the lower left corner of the screen.
- [SEL] key: Selects the parameter to be adjusted. The selected parameter is highlighted on the screen.
- Tlačítka [+] a [-]: Upravte hodnotu vybraného parametru.
- Tlačítko [OK]: Freezes the waveform (enters pause acquisition state). Press again to resume acquisition.
- Signal Generator Outputs: Includes sine wave, triangle wave, and square wave outputs (test signal, earth wire).
5.2. Výběr jazyka
To select Chinese display, short JP4 on the back of the board with solder. For English display, ensure JP4 is open.
5.3. Waveform Display Examples
6. Specifikace
| Parametr | Hodnota |
|---|---|
| Šířka pásma | 500 kHz |
| ADC Accuracy | 12 bitů |
| S. v reálném časeampsazba ling | 1.5 Msps |
| Délka vyrovnávací paměti tvaru vlny | 1024 bodů |
| Rozsah vertikální citlivosti | 10 mV/dílek - 5 V/dílek |
| Vstupní impedance | 1 MΩ |
| Maximální vstupní objemtage | 50 Vpk |
| Režim spojky | DC, AC, GND |
| Horizontální rozsah časové základny | 1us/div - 500s/div |
| Režim spouštění | Auto, Conventional, Single |
| Spouštěcí hrana | Stoupající/Klesající |
| Napájení | DC 5V (via USB Type-C interface) |
| Aktuální spotřeba | <100 mA |
| Rozměry produktu | Rozměr 118 x 76 x 12 mm |
7. Řešení problémů
- Bez síly: Ensure the USB Type-C cable is securely connected to a 5V DC power source and the oscilloscope. Check the power source for functionality.
- No waveform display:
- Verify the probe is correctly connected to both the oscilloscope and the test circuit.
- Check the Coupling Mode (CPL switch) is set appropriately (AC/DC, not GND unless intentionally grounding the input).
- Adjust the vertical sensitivity (SEN1/SEN2 switches) and horizontal time base to match the expected signal.
- Ensure the [OK] button is not pressed, which would pause waveform acquisition.
- Nestabilní tvar vlny: Adjust the trigger mode and trigger edge settings to stabilize the waveform.
- Nesprávné hodnoty:
- Zajistěte správné uzemnění osciloskopu a testovaného obvodu.
- Check for loose connections or faulty components if this is a newly assembled kit.
8. Údržba
- Čištění: K čištění zařízení používejte měkký, suchý hadřík. Nepoužívejte tekutiny ani abrazivní čisticí prostředky.
- Skladování: Store the oscilloscope in a dry, dust-free environment when not in use.
- Zacházení: Handle the device with care to prevent damage to components or connections.
9. Uživatelské tipy
- When assembling, double-check resistor values with a multimeter before soldering to avoid errors, as color codes can sometimes be hard to read.
- Take your time with soldering, ensuring good solder joints to prevent intermittent connections.
- For educational purposes, experiment with different signal types from the built-in generator to understand oscilloscope functions.
10. Záruka a podpora
For any technical support or inquiries regarding your DSO183 Digital Oscilloscope DIY Kit, please contact the seller or manufacturer directly. Keep your purchase records for reference.
