1. Úvod
The TSUN MA06LS is an integrated magnetic grid ruler and digital display meter designed for high-precision measurement. It features a compact design, intelligent LCD with backlight, and non-contact measurement for durability and resistance to oil and dust. This manual provides detailed instructions for the proper installation, operation, and maintenance of your MA06LS device.
Klíčové vlastnosti:
- MA06LS Magnetic Grating Digital Display Meter
- Intelligent LCD with backlight display mode
- Icon mode defines common function shortcut keys (modify current value, modify direction, sensor adaptive mode)
- Non-contact measurement, no wear, high protection level, oil-resistant, dust-resistant
- Selectable linear measurement and angle measurement
2. Specifikace
Elektrický výkon:
| Parametr | Hodnota |
|---|---|
| Přesnost systému | ± (0.03 + 0.01 * L) L unit: meter |
| Opakovatelnost | Max. ±0.01mm |
| Rezoluce | 0.01, 0.05, 0.1, 1 |
| Rozsah zobrazení | -99999 ~ 99999 |
| Aktuální spotřeba | Max. 400uA |
| Vestavěná baterie | Two AA batteries (ultra-long standby) |
| Provozní teplota | -20 ℃ ~ 70 ℃ |
Mechanical Performance:
| Parametr | Hodnota |
|---|---|
| Maximum External Dimensions | 73.7 mm * 36.2 mm * 29.56 mm |
| Velikost otvoru | 67.6 mm * 32.1 mm |
| Read Head Cable Length | Default 1M (customizable) |
| Read Head Gap | Standard 1~2mm |
| Rychlost pohybu | Max. 5m/s |
| Matching Magnetic Ruler | TR50/5mm + 5mm |
3. Nastavení a instalace
Magnetic Grating Ruler Components:
The magnetic grating ruler consists of 3 parts with a total thickness of 1.8mm and a width of 10mm. It is supplied in a 50M roll package.
- Flexible Magnetic Ruler (A): The core magnetic component.
- Non-magnetic Steel Strip (B): Provides structural support.
- Protective Steel Strip (C): Protects the flexible magnetic ruler (A).
Adhesive Magnetic Strip Installation:
The thin ruler strip must be adhered to a clean, dry, and flat surface. For cleaning, a mixture of 50% alcohol and 50% water or heptane is recommended (refer to manufacturer's tips for solvent contact). Ensure surfaces like copper or brass are clean and free of any oxide layer before adhesion.
Read Head Installation:
- Kontrola vzdálenosti: The distance between the read head and the magnetic ruler must be controlled between 0.8mm and 1.0mm.
- Zarovnání: When installing the read head, pay attention to the read head mark and align it with the inductive magnetic ruler according to the arrow direction.
- Angle Deviation: Ensure the read head installation angle deviation meets the requirements shown in Figure 5 (e.g., +/-3mm, +/-5 degrees, +/-1.5 degrees).
- Měřicí spára: Use a 0.8mm thick feeler gauge during installation. Remove it after the read head is securely mounted to sense the magnetic strip.
Opatření:
- The standard distance between the read head and the magnetic tape is 1mm.
- If the installation deviation is too large, it will affect measurement accuracy or even render the product unusable.
- The bending radius of the read head sensor cable must be greater than 25mm.
- The device should be installed more than 0.5 meters away from circuit breakers, relays, motor capacitors, brakes, pulse width modulators, and similar equipment.
- Cable routing must be separated from power lines to reduce noise interference.
4. Provoz
Funkce tlačítek:
The MA06LS features four primary buttons: P(F1), F2 (Up Arrow), F3 (Right Arrow), and C(F4).
| Button/Function No. | Popis funkce | Poznámky |
|---|---|---|
| P (F1) | Function Key / Confirm Key: Long press to enter parameter settings. Press again to select the parameter to modify. After modification, press 'P' to confirm and exit. | Used for P01, P21, P22. |
| F2 (Up Arrow) | Modify Key: Used to adjust parameter values. | |
| F3 (Right Arrow) | Klíč přepínače: Used to switch between parameters and digits during input. | |
| C (F4) | Klávesa ukončení: Clears or exits the current mode. | Wake up from timed screen off by pressing any key. |
Nastavení parametrů:
| Číslo parametru | Funkce | Rozsah/Možnosti | Výchozí | Popis | Heslo |
|---|---|---|---|---|---|
| P01 | Current Value Setting | -99999~99999 | 0 | Saves the input value as the current value. | Žádný |
| P02 | Measurement Direction | 0~1 | 1 | 0 or 1 represents two directions. Can change sensor direction. | Žádný |
| P03 | Adaptive Calibration | GO | GO | Enter state, slowly move sensor (can move repeatedly) about 150MM for 10 seconds. Returns to current measurement after learning. If calibration fails, adjust sensor-magnetic strip distance (recommended 1-2MM). | Žádný |
| P10 | Measurement Unit Switching | Length/Angle/Inch | 00 | 00: mm; absolute mode; 01: mm; relative mode; 10: INCH; absolute mode; 11: INCH; relative mode; 20: Angle; absolute mode; 21: Angle; relative mode. | 1234 |
| P11 | Měřítko | 0.00001~2.99999 | 1 | Displayed value = actual measured value * scale factor. | 1234 |
| P12 | Concentric Circle Diameter | 0.01~999.99 | 500.00 | Diameter value of the disk where the magnetic strip is attached. Diameter needs to add magnetic strip thickness (1.5mm*2=3mm). | Žádný |
| P13 | Rezoluce | 0.1, 0.05, 0.01, 1 | 0.1 | Length unit: mm; Angle corresponding unit: °. | 1234 |
| P15 | Timed Screen Off | 0~1 | 0 | 0: Do not enable automatic screen off; 1: Default off after 5 minutes. | 1234 |
| P20 | Obnovit tovární nastavení | TAK URČITĚ? | Žádný | Restores default factory settings. | 4321 |
| P21 | Full Machine Debugging Completion Backup Function | TAK URČITĚ? | Žádný | Press 'P' to confirm. | 5321 (to enter parameters) |
| P22 | Restore Full Machine Debugging Completion Backup | TAK URČITĚ? | Žádný | Press 'P' to confirm. | 5321 (to enter parameters) |
5. Údržba
Výměna baterie:
The MA06LS uses two AA batteries. When the low battery indicator appears on the display, replace the batteries immediately. To avoid data loss, replace them one by one.
Čištění:
Keep the magnetic strip and read head clean and free of debris. Use a soft, dry cloth. If necessary, a 50% alcohol and 50% water mixture or heptane can be used for cleaning the magnetic strip, ensuring no oxide layers remain on metal surfaces.
Skladování:
Store the device in a dry environment within the specified operating temperature range (-20℃ to 70℃) when not in use for extended periods.
6. Řešení problémů
Error Prompts:
| Kód chyby | Popis | Navrhovaná akce |
|---|---|---|
| E01 | Porucha snímače. | Check sensor connection and integrity. |
| E02, E03 | Poškození snímače. | Vyměňte snímač. |
| E04 | Magnetic strip detection failed: No magnetic strip, magnetic strip damaged, or read head too far from magnetic strip. | Verify magnetic strip presence and condition. Adjust read head distance (0.8-1.0mm). |
| E05 | Baterie je příliš slabá. | Replace AA batteries immediately, one by one. |
| E06 | Read head too close to magnetic tape. | Adjust read head distance to 0.8-1.0mm. |
| E07 | Read head too far from magnetic tape. | Adjust read head distance to 0.8-1.0mm. |
| E08 | Measured value exceeds display range. | Ensure measurements are within -99999 to 99999. |
Obecné odstraňování problémů:
- If the display is blank, check battery power and ensure they are correctly inserted.
- If readings are inconsistent, verify the read head-to-magnetic strip gap and ensure proper alignment.
- Ensure no strong electromagnetic interference sources are near the device.
7. Uživatelské tipy
- For optimal accuracy, always ensure the magnetic strip and read head are clean and free of dust or oil.
- When performing adaptive calibration (P03), move the sensor slowly and consistently over the magnetic strip for the recommended distance.
- If you frequently switch between measurement units or modes, consider noting down the relevant parameter numbers (P10, P13) and their password (1234) for quick access.
- To prolong battery life, enable the timed screen off function (P15) if not actively monitoring measurements.
8. Záruka a podpora
Pro informace o záruce, technickou podporu nebo servisní dotazy se prosím obraťte na prodejce, u kterého jste výrobek zakoupili, nebo přímo na výrobce. Uschovejte si účtenku jako doklad o koupi.
