1. Úvod
This manual provides instructions for the BENINCA TO.GO 4WV garage door opener remote control. This device is designed to operate BENINCA garage doors and gate openers using a 433.92MHz rolling code frequency. Please read this manual carefully before use to ensure proper operation and longevity of your remote control.
2. Konec produktuview
The BENINCA TO.GO 4WV is a compact and reliable hand transmitter featuring four buttons for controlling multiple functions or devices. It utilizes rolling code technology for enhanced security.
2.1 Obsah balení
- 1 x dálkové ovládání BENINCA TO.GO 4WV
- 1 x baterie (předinstalovaná)
- 1 x Keychain
2.2 Vizuální podoba produktu
Obrázek 1: Přední strana view of the remote control with four white buttons.
Obrázek 2: Detailní přední strana view showing the LED indicator and buttons.
Obrázek 3: Boční profíkfile dálkového ovládání.
Obrázek 4: Úhlové view highlighting the ergonomic design.
Obrázek 5: Zadní view with the battery compartment cover.
Figure 6: Dimensions of the remote control (approximately 70mm x 40mm x 14mm).
2.3 Produktové video
Video 1: Unboxing and demonstration of button functionality.
3. Specifikace
| Funkce | Specifikace |
|---|---|
| Model | BENINCA TO.GO 4WV |
| Kompatibilní modely | BENINCA TO.GO 2WV, BENINCA TO.GO 4WV |
| Frekvence | 433.92 MHz |
| Metoda kódování | Rolling Code |
| Tlačítka | 4 |
| Baterie | V ceně |
| Původ | pevninská Čína |
| Osvědčení | CE |
4. Nastavení a programování
To program your BENINCA TO.GO 4WV remote control, you will need access to your existing BENINCA receiver or opener unit. The programming procedure typically involves interacting directly with the receiver unit, not just the remote itself.
General Programming Steps (may vary by receiver model):
- Vyhledejte přijímač: Find the control unit for your garage door or gate opener. This is usually located near the motor or inside a control box.
- Access Programming Button: On the receiver, locate the programming button (often labeled 'PROG', 'MEMO', 'LEARN', or similar). Consult your original BENINCA receiver/opener manual for its exact location and labeling.
- Aktivace režimu učení: Press and release the programming button on the receiver. An LED indicator on the receiver should light up or flash, indicating it is in learning mode.
- Transmit Code from New Remote: Within a few seconds (usually 5-10 seconds), press and hold the desired button on your new BENINCA TO.GO 4WV remote control that you wish to program.
- Potvrzení programování: The LED on the receiver should change its state (e.g., flash rapidly, turn off, or light up solid) to confirm successful programming. Release the button on the remote.
- Test dálkového ovládání: Wait a few seconds for the receiver to exit learning mode, then test the newly programmed button on your remote control to ensure it operates the garage door or gate.
Important: Always refer to the specific instruction manual for your BENINCA receiver/opener model for precise programming steps, as procedures can vary. Ensure you have access to your receiver before attempting to program the remote.
5. Provoz
Jakmile je dálkový ovladač BENINCA TO.GO 4WV naprogramován, je jeho ovládání velmi jednoduché:
- Namiřte dálkový ovladač na otvírač garážových vrat nebo brány.
- Press the programmed button corresponding to the function you wish to activate (e.g., open, close, stop).
- The LED indicator on the remote control will light up briefly when a button is pressed, confirming signal transmission.
Figure 7: Demonstrating button press on the remote control.
6. Údržba
6.1 Výměna baterie
The remote control comes with a pre-installed battery. If the remote's range decreases significantly or the LED indicator does not light up when a button is pressed, it's likely time to replace the battery.
Chcete-li vyměnit baterii:
- Vyhledejte kryt přihrádky na baterie na zadní straně dálkového ovladače (viz obrázek 5).
- Carefully open the compartment using a small screwdriver or by sliding the cover as indicated.
- Remove the old battery. Note its orientation (+/-).
- Vložte novou baterii stejného typu a dbejte na správnou polaritu.
- Bezpečně zavřete kryt bateriového prostoru.
Warning: Dispose of old batteries responsibly according to local regulations. Keep batteries out of reach of children.
6.2 Čištění
Dálkový ovladač otírejte měkkým, suchým hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla, protože by mohly poškodit ovladač.asing nebo vnitřních součástí.
7. Řešení problémů
If your remote control is not functioning as expected, try the following troubleshooting steps:
- Dálkový ovladač nefunguje po naprogramování: Double-check the programming steps in your receiver's manual. Ensure the receiver was in learning mode and the correct button was pressed on the remote.
- Krátký provozní dosah: Replace the battery in the remote control. Ensure there are no obstructions between the remote and the receiver. Check for sources of radio interference (e.g., other wireless devices, metal structures).
- LED on remote does not light up: The battery may be dead or incorrectly installed. Replace the battery.
- Dálkové ovládání funguje přerušovaně: This could indicate a low battery, interference, or a loose connection inside the remote. Try replacing the battery first.
If the issue persists after trying these steps, contact customer support or a qualified technician.
8. Uživatelské tipy
- Keep Receiver Manual Handy: For programming and advanced settings, always refer to the instruction manual of your BENINCA garage door or gate receiver/opener. This is crucial for successful setup.
- Testovací rozsah: After programming, test the remote's operating range from various distances and angles to ensure reliable performance.
- Secure Your Remote: Treat your remote control like a key. Keep it in a secure location to prevent unauthorized access to your garage or gate.
9. Záruka a podpora
Informace o záruce, technickou podporu nebo servisní dotazy naleznete v dokumentaci dodané s vaším nákupem nebo se obraťte přímo na prodejce. Uschovejte si doklad o koupi pro případ reklamace.
