1. Úvod
The ATTEN AT-8502D is an intelligent, lead-free 2-in-1 digital rework station, combining a hot air rework station and a soldering station. Designed for versatility and precision, it is ideal for R&D, production, and scientific research laboratories. Its user-friendly interface and space-saving design make it a valuable tool for various electronic repair and assembly tasks.
Figure 1: ATTEN AT-8502D Digital Rework Station
2. Klíčové vlastnosti
- Design 2 v 1: Combines a hot air station and a soldering station, optimizing workspace.
- Vysoký výkon: Hot air station with 550W for rapid heating and high efficiency; Soldering station with 50W for quick heating and temperature recovery.
- Duální LCD displej: Provides clear, visualized operation with accurate temperature and airflow readings.
- Přesné ovládání: MCU precise temperature control function ensures stable and accurate temperature.
- Membránové čerpadlo: High-power diaphragm pump suitable for a wide variety of nozzles.
- Funkce paměti: Three sets of shortcut air volume/temperature settings to simplify operations and allow quick recall of preferred settings.
- Kalibrace teploty: Supports temperature calibration within a range of ±50°C.
- Úspora energie: Features auto-sleep and auto-standby functions, with a built-in sleep sensor in the hot air gun handle.
- Flexibilní provoz: Hot air gun handle can be installed on either the left or right side.
- Jednotky teploty: Supports switchable °C and °F display.
- Bezpečnostní funkce: Intelligent cooling system and deferred power-off function. Cold air function to cool components. Error/fault indications for 'H-E' and 'S-E'.
3. Obsah balení
Po obdržení zkontrolujte prosím obsah balíku, abyste se ujistili, že jsou všechny položky přítomny a nepoškozené:
- ATTEN AT-8502D Main Unit
- Rukojeť horkovzdušné pistole
- Rukojeť páječky
- Hot Air Nozzles (various types, e.g., A-1126, A-1125, A-1130, A-1170)
- Soldering Iron Tips (various types, e.g., T900-0.5C, T900-4C, T900-0.8D, T900-1.2D, T900-LB, T900-0.8C, T900-2C, T900-1.6D, T900-B, T900-IS, T900-1C, T900-SB, T900-2.4D, T900-SK, T900-I, T900-3C, T900-K, T900-SI)
- Soldering Iron Stand with cleaning sponge
- Napájecí kabel
- Uživatelská příručka
Obrázek 2: Zahrnuté součásti
4. Pokyny k nastavení
- Rozbalení: Opatrně vyjměte všechny součásti z obalu. Obal si uschovejte pro budoucí skladování nebo přepravu.
- Umístění: Place the main unit on a stable, heat-resistant, and well-ventilated surface. Ensure there is adequate space around the unit for airflow.
- Připojení horkovzdušné pistole: Connect the hot air gun handle to the designated port on the main unit. Ensure the connection is secure.
- Připojení páječky: Connect the soldering iron handle to its designated port on the main unit. Place the soldering iron in its stand.
- Připojení napájení: Connect the power cord to the main unit and then to a suitable power outlet (110V or 220V, depending on your model).
- Nozzle/Tip Installation: Select the appropriate hot air nozzle for your task and securely attach it to the hot air gun. For the soldering iron, ensure a suitable tip is installed.
Obrázek 3: Trysky horkovzdušné pistole
5. Návod k obsluze
5.1. Obecný provoz
- Zapnutí: Flip the main ON/OFF switch on the front panel to the 'ON' position. The dual LCD displays will illuminate.
- Výběr režimu: The unit features separate controls for the hot air rework station and the soldering station.
5.2. Hot Air Station Operation
Obrázek 4: Ovládací prvky na předním panelu
- Activate Hot Air: Press the left 'POWER' button to activate the hot air station.
- Upravte průtok vzduchu: Use the 'UP' and 'DOWN' buttons below the 'SMD REWORK' display to adjust the air flow (020-100 grades).
- Upravit teplotu: Press the 'SET' button to switch to temperature settings. Use the 'UP' and 'DOWN' buttons to increase or decrease the temperature (100°C-500°C). Press 'SET' again to confirm and exit.
- Funkce paměti: The hot air station has 3 memory channels. Short press the left 'POWER' button and '1', '2', or '3' to quickly use a stored temperature. Long press the left 'POWER' button and '1', '2', or '3' to store the current temperature and air flow settings.
- Pohotovostní režim: When the hot air gun handle is placed on its holder, the station will automatically enter sleep status ('SLP') and cool down. Picking up the handle will reactivate it.
- Funkce studeného vzduchu: The unit can switch between hot and cold air. Refer to the video demonstration for specific button presses.
5.3. Soldering Station Operation
- Aktivace páječky: Press the right 'POWER' button to activate the soldering station.
- Upravit teplotu: Press the 'SET' button to switch to temperature settings. Use the 'UP' and 'DOWN' buttons to increase or decrease the temperature (200°C-480°C). Press 'SET' again to confirm and exit.
- Funkce paměti: The soldering station has 3 memory channels. Short press the right 'POWER' button and '1', '2', or '3' to quickly use a stored temperature. Long press the right 'POWER' button and '1', '2', or '3' to store the current temperature.
5.4. Přepínání teplotních jednotek (°C/°F)
To switch between Celsius and Fahrenheit, simultaneously press the 'UP', 'DOWN', 'SET' buttons, and the main ON/OFF switch button.
5.5. Teplotní kompenzace
The temperature compensation setting is ±50°C. To enter this setting, press the hot air gun handle's 'X' button and the left 'POWER' button simultaneously. Use 'UP' to increase and 'DOWN' to decrease the compensation value. Press 'SET' to confirm and exit. Calibration is required when replacing the heater or handle.
6. Údržba
- Čištění: Regularly clean the hot air gun nozzles and soldering iron tips to ensure optimal performance. Use a damp sponge for soldering tips and a brush for nozzles.
- Péče o hroty: Always tin the soldering iron tip before storing it to prevent oxidation. Replace worn or damaged tips promptly.
- Péče o trysku: Ensure hot air nozzles are free from debris. Replace if bent or damaged to maintain proper airflow.
- Generální úklid: Keep the main unit clean and free of dust. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
- Skladování: Pokud přístroj nepoužíváte, skladujte jej v suchém a bezprašném prostředí.
7. Řešení problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Jednotka se nezapne | Žádné napájení; Uvolněný napájecí kabel; Hlavní vypínač vypnutý | Check power outlet; Ensure power cord is securely connected; Turn main switch ON |
| Hot air gun not heating | Heater element failure; Connection issue; Incorrect settings | Check hot air gun connection; Verify temperature settings; Contact support if heater element is faulty |
| Páječka se nezahřívá | Heater element failure; Connection issue; Incorrect settings | Check soldering iron connection; Verify temperature settings; Contact support if heater element is faulty |
| Display shows "H-E" or "S-E" | Heater or sensor error | Turn off the unit, check connections, and restart. If error persists, contact technical support. |
| Inconsistent temperature readings | Needs calibration; Faulty sensor | Perform temperature calibration as per section 5.5; Contact support if sensor is faulty |
8. Specifikace
| Funkce | Specifikace |
|---|---|
| Číslo modelu | AT-8502D |
| Značka | V DESET |
| Hot Air Station Power | 550W |
| Soldering Station Power | 50W |
| Rozsah teplot horkého vzduchu | 100 °C - 500 °C (212 °F - 932 °F) |
| Teplotní rozsah páječky | 200 °C - 480 °C (392 °F - 896 °F) |
| Nastavení průtoku vzduchu | 020-100 stupně |
| Teplotní kompenzace | ±50 °C |
| svtage | 110V / 220V (volitelné) |
| Typ zobrazení | Duální LCD |
| Osvědčení | CE |
| Původ | pevninská Čína |
9. Uživatelské tipy
- Always wear appropriate personal protective equipment, including safety glasses and heat-resistant gloves, when operating the rework station.
- Ensure your workspace is well-ventilated to dissipate fumes from soldering and desoldering.
- Regularly clean and tin your soldering iron tips to prolong their lifespan and ensure efficient heat transfer.
- Utilize the memory preset functions for frequently used temperature and airflow combinations to save time and ensure consistent results.
- When desoldering sensitive components with the hot air gun, use the lowest effective temperature and airflow to prevent damage to surrounding components or the PCB.
10. Záruka a podpora
The ATTEN AT-8502D Digital Rework Station comes with a standard manufacturer's warranty. For specific warranty terms, duration, and conditions, please refer to the warranty card included in your product packaging or contact the seller/manufacturer directly.
For technical support, service, or inquiries regarding your product, please reach out to the authorized ATTEN service center or your point of purchase. Ensure you have your product model number and purchase details ready when contacting support.
