Miboxer FUT020 RGB LED Controller Instruction Manual

1. Úvod

The Miboxer FUT020 is a DC12-24V 2.4GHz RF RGB LED Controller designed for controlling RGB LED strips and FCOB lighting. It offers brightness and saturation control, allowing for a wide range of color adjustments and dynamic lighting effects. This manual provides detailed instructions for the proper installation, operation, and maintenance of your FUT020 controller.

2. Specifikace

2.1. LED Controller (FUT020)

• Číslo modelu: FUT020
• Vstupní objemtage: DC12-24V
• výstup: 6A/Channel (3 circuits: R/G/B)
• Celkový výkon: Max 10A
• RF: 2.4 GHz
• Kontrolní vzdálenost: 30m (bezbariérový prostor)
• Pracovní teplota: -10~40°C
• Výstupní připojení: Společná anoda
• Rozměry: D 85 mm * Š 45 mm * V 22 mm
• Materiál: ABS

2.2. Remote Control (FUT020)

• Číslo modelu: FUT020
• Pracovní svtage: 3V (2x AAA baterie)
• Spotřeba energie v pohotovostním režimu: <20 uA
• Vysílací výkon: 6dBm
• RF: 2.4 GHz
• Kontrolní vzdálenost: 30m (bezbariérový prostor)
• Přenosová frekvence: 2400-2483.5 MHz
• Metoda modulace: GFSK
• Pracovní teplota: -10~40°C
• Materiál krytu: ABS

3. Nastavení

3.1. Controller Wiring

Ensure all power is disconnected before wiring. Connect the LED strip to the controller and the power supply to the controller as shown in the diagram below. The controller uses a common anode connection method.

3.2. Instalace baterie dálkového ovládání

The remote control requires 2 AAA batteries. Open the battery compartment on the back of the remote and insert the batteries, ensuring correct polarity.

3.3. Matching Remote Control to Receiver

Typically, the remote control and receiver are pre-matched from the factory. If re-matching is needed:

1. Ujistěte se, že je ovladač vypnutý.
2. Zapněte ovladač.
3. Within 3 seconds of powering on, press Key 4 (Turn Up/Brightness/Speed) once.
4. The connected LED light will blink 3 times, indicating successful matching.

3.4. Clearing Code

To clear the matching code from the receiver:

1. Ujistěte se, že je ovladač vypnutý.
2. Zapněte ovladač.
3. Within 3 seconds of powering on, press Key 4 (Turn Up/Brightness/Speed) five times.
4. The connected LED light will blink 6 times, indicating successful code clearing.

4. Návod k obsluze

The FUT020 remote control features a user-friendly interface for various lighting adjustments.

4.1. Funkce kláves

• Key 1 (ON/OFF): Zapíná nebo vypíná LED světla.
• Key 2 (Light Changing Mode): Activates and cycles through 15 different dynamic lighting modes.
• Key 3 (Color Light/White Light Switching Mode): Toggles between color mode and white light mode.
• Key 4 (Turn Up): Increases brightness or speed of dynamic modes.
• Key 5 (Turn Down): Decreases brightness or speed of dynamic modes.
• Barevný prsten: Touch the color ring to select any desired color.

4.2. Jak používat

1. Zapnutí/vypnutí: Press Key 1 to turn the lights on or off.
2. Dynamické režimy: Press Key 2 to activate the light changing mode. Keep pressing Key 2 to cycle through the 15 available programs.
3. Režim bílého světla: Press Key 3 once to activate the pure white light mode. Adjust the brightness using Key 4 (up) or Key 5 (down).
4. Výběr barvy: Press Key 3 twice to activate the color ring. You can then select any color by touching the color ring. Adjust the brightness using Key 4 (up) or Key 5 (down).
5. Funkce životopisu: The controller will remember the last setting and resume it when powered on again.

4.3. Dynamic Mode Chart (Key 2)

The following table details the 15 dynamic modes available via Key 2:

5. Údržba

5.1. Remote Control Sensitivity

To maintain the sensitivity of the color ring, avoid touching or pressing it while loading the batteries. After installing batteries, wait approximately 3 seconds before using the remote controller. If the color ring becomes unresponsive, try reloading the batteries.

5.2. Čištění

Wipe the controller and remote control with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.

6. Řešení problémů

• Světla nereagují na dálkový ovladač:
  1. Zkontrolujte, zda jsou baterie v dálkovém ovladači správně vloženy a zda mají dostatečnou kapacitu. V případě potřeby je vyměňte.
  2. Ensure the remote is matched to the receiver. Follow the 'Matching Remote Control to Receiver' steps in Section 3.3.
  3. Verify that the controller is receiving power and the LED strip is correctly wired.
• Color ring not sensitive:
  1. Reload the batteries in the remote control.
  2. Wait 3 seconds after battery installation before attempting to use the color ring.
• Unexpected light behavior:
  1. Try clearing the remote's code and re-matching it to the receiver (Section 3.4 and 3.3).
  2. Ensure the correct mode is selected (color light, white light, or dynamic mode).

7. Uživatelské tipy

• For optimal performance, ensure the controller is installed in a well-ventilated area to prevent overheating.
• Keep the remote control within the specified 30m barrier-free range for reliable operation. Obstacles can reduce this range.
• When experimenting with dynamic modes, use the speed adjustment (Key 4/5) to find the perfect pace for your ambiance.

8. Záruka a podpora

8.1. Záruka

This Miboxer FUT020 controller comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

8.2. Certifikace

The product is certified with CCC, CE, EMC, FCC, LVD, ROHS, and UL standards, ensuring compliance with relevant safety and quality regulations.

8.3. Technická podpora

For technical assistance or further inquiries, please contact your retailer or the Miboxer customer support. Refer to the product packaging or Miboxer's official webstránky pro kontaktní údaje.