Zavedení
The Aigo AC SE 120 is a high-performance all-in-one (AIO) liquid CPU cooler designed to provide efficient cooling for your processor while adding a vibrant aesthetic to your PC build with its Rainbow (RGB) lighting. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your cooler.
Specifikace
Refer to the table below for detailed technical specifications of the Aigo AC SE 120 Liquid CPU Cooler.
| Atribut | Hodnota |
|---|---|
| Typ | Kapalný chladič CPU |
| Číslo modelu | ACSE120-WH |
| Značka | Aigo |
| Kompatibilní zásuvky | Intel: LGA 2066/2011-V3/2011/1700/1366/1200/115X - AMD: FM1/FM2/FM2+/AM2/AM2+/AM3/AM3+/AM4 |
| Water Block Size | 71 x 66.5 x 45 mm |
| Délka trubky | 330 mm |
| Rychlost čerpadla | 3200 ± 10 % RPM |
| Pump Voltage | 12V |
| Pump Bearing | Keramický |
| Velikost chladiče | 154 x 120 x 27 mm |
| Velikost ventilátoru | 120 x 120 x 25 mm |
| Rychlost ventilátoru | 800 ~ 1800 ± 10% RPM |
| Fan Rated Voltage | 12V |
| Proudění vzduchu ventilátorem | 64.05 CFM |
| Hladina hluku ventilátoru | 30 dBA ± 10% |
| Static Fan Pressure | 1.85 mm H2 |
Obsah balení
Zkontrolujte prosím, zda jsou ve vašem balení obsaženy všechny následující komponenty:
- Aigo AC SE 120 Liquid CPU Cooler (Radiator, Pump/Water Block, Tubes, Pre-filled coolant)
- 120mm Rainbow (RGB) Fan
- Mounting hardware for Intel sockets (LGA 2066/2011-V3/2011/1700/1366/1200/115X)
- Mounting hardware for AMD sockets (FM1/FM2/FM2+/AM2/AM2+/AM3/AM3+/AM4)
- Tepelná pasta
- Fan and RGB connection cables
- Uživatelská příručka
Průvodce instalací
Before beginning installation, ensure your system is powered off and unplugged. Refer to your motherboard manual for specific CPU socket mounting instructions if needed.
1. Příprava procesoru a základní desky
- Unpack all components and ensure you have the correct mounting hardware for your CPU socket (Intel or AMD).
- Očistěte povrch procesoru isopropylalkoholem, abyste odstranili starou teplovodivou pastu nebo zbytky.
- Install the appropriate backplate (if required for your socket) on the rear of the motherboard.
2. Apply Thermal Paste
Apply a small amount of thermal paste (included) to the center of your CPU's integrated heat spreader (IHS). A pea-sized dot is usually sufficient. The pressure from the water block will spread it evenly.
3. Namontujte vodní blok
- Attach the correct mounting brackets to the water block/pump unit.
- Carefully align the water block with the CPU and the mounting holes on the motherboard.
- Gently place the water block onto the CPU, ensuring even contact.
- Secure the water block using the provided screws, tightening them in a diagonal pattern until snug. Do not overtighten.
4. Mount the Fan to the Radiator
- Using the longer screws, attach the 120mm fan to the radiator. Ensure the fan is oriented to push or pull air in the desired direction for your case's airflow.
5. Mount the Radiator to the PC Case
- Identify a suitable mounting location in your PC case for a 120mm radiator (e.g., rear exhaust, top, or front intake).
- Secure the radiator to the case using the shorter screws provided.
6. Připojte kabely
- Connect the pump's 3-pin or 4-pin power cable to the designated CPU_FAN or AIO_PUMP header on your motherboard.
- Connect the fan's 4-pin PWM cable to a CPU_FAN or SYS_FAN header on your motherboard.
- Connect the RGB cable from the fan and pump to an available 3-pin 5V Addressable RGB (ARGB) header on your motherboard or an RGB controller (if included/used).
Návod k obsluze
Once installed, the Aigo AC SE 120 operates automatically. The pump and fan speeds are typically controlled by your motherboard's BIOS/UEFI settings or dedicated software, based on CPU temperature.
- Počáteční zapnutí: After installation, power on your PC. Check for any unusual noises or leaks. The pump should run quietly, and the fan should spin.
- Nastavení BIOSu/UEFI: Access your motherboard's BIOS/UEFI to ensure the CPU fan header is set to PWM mode (if applicable) and that fan curves are configured for optimal cooling and noise levels.
- Ovládání RGB: If connected to an ARGB header, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync) or a dedicated RGB controller.
- Monitorování teploty: Use monitoring software (e.g., HWMonitor, Core Temp) to verify CPU temperatures are within safe operating limits during idle and load conditions.
Údržba
Pravidelná údržba pomáhá zajistit dlouhou životnost a optimální výkon vašeho kapalinového chladiče CPU.
- Čištění prachu: Pravidelně čistěte žebra chladiče a lopatky ventilátoru, abyste zabránili hromadění prachu, který může bránit proudění vzduchu a snižovat účinnost chlazení. Používejte stlačený vzduch nebo měkký kartáč.
- Správa kabelů: Ujistěte se, že všechny kabely jsou úhledně vedeny a nezasahují do lopatek ventilátoru ani jiných součástí.
- Zkontrolujte netěsnosti: Although rare, regularly inspect the tubes and connections for any signs of coolant leakage. If a leak is detected, power off your system immediately and contact support.
- Hlučnost čerpadla: Listen for any unusual pump noises. A gurgling sound might indicate air bubbles, which usually resolve themselves over time. Persistent loud noises could indicate an issue.
Odstraňování problémů
Zde jsou některé běžné problémy a jejich možná řešení:
- Vysoké teploty procesoru:
- Ensure the water block is securely mounted and making good contact with the CPU.
- Ověřte nanesení teplovodivé pasty.
- Check that the pump and fan are receiving power and spinning correctly.
- Očistěte prach z žeber chladiče.
- Zajistěte správné proudění vzduchu uvnitř skříně počítače.
- Pump Not Running/Making Noise:
- Check the pump's power connection to the motherboard.
- Ensure the correct header (CPU_FAN or AIO_PUMP) is used and configured in BIOS.
- A slight gurgling sound initially is normal as air bubbles settle. If persistent and loud, try gently tilting your PC case to help dislodge air bubbles.
- Fan Not Spinning/RGB Not Working:
- Verify all fan and RGB cables are securely connected to the motherboard or controller.
- Check your motherboard's BIOS/UEFI settings for fan control.
- Ujistěte se, že je software RGB vaší základní desky správně nainstalován a nakonfigurován.
- Cooler Leaking:
- Immediately power off your system and unplug it.
- Do not attempt to repair. Contact customer support for assistance.
Tipy pro uživatele
To get the most out of your Aigo AC SE 120 Liquid CPU Cooler:
- Optimalizace proudění vzduchu: Ensure your PC case has good overall airflow to help dissipate heat from the radiator effectively.
- Monitorovat teploty: Regularly monitor your CPU temperatures, especially during demanding tasks, to ensure stable performance.
- Správa kabelů: Good cable management not only improves aesthetics but also enhances airflow within your case.
- Ovládání softwaru: Utilize your motherboard's fan control and RGB software to customize performance and lighting to your preference.
Záruka a podpora
The Aigo AC SE 120 Liquid CPU Cooler comes with a Záruka 12 měsíců od data nákupu. Tato záruka se vztahuje na výrobní vady a poruchy při běžném používání. Uschovejte si prosím doklad o koupi pro případ uplatnění záruky.
For technical support, warranty claims, or further assistance, please contact the seller or the manufacturer's official support channels. Refer to the contact information provided by your retailer or on the official Aigo webmísto.
