MATEKSYS MBEC12S Micro BEC Instruction Manual

1. Úvod

The MATEKSYS MBEC12S is a compact and efficient Micro Battery Eliminator Circuit (BEC) designed for various RC applications, including model airplanes, helicopters, and FPV racing drones. It converts a wide input voltage range of 6V to 60V DC into a stable, selectable output of 5V, 9V, or 12V DC, providing reliable power to your sensitive electronic components.

2. Specifikace

2.1. Continuous Load Current & Output Ripple

The continuous load current depends on the input voltage and heat dissipation. The following table provides typical continuous current ratings and output ripple values at room temperature (22°C) without an additional heat sink:

3. Nastavení a instalace

1. Výstupní objemtage Výběr: The MBEC12S defaults to 5V output. To change the output voltage to 9V or 12V, you must bridge the corresponding solder pads on the module. Refer to Figure 2 for the location of the '9V' and '12V' pads.
   • For 9V output: Bridge the '9V' solder pad.
   • For 12V output: Bridge the '12V' solder pad.
   • Ensure only one output voltage is selected at a time. Do not bridge both 9V and 12V pads simultaneously.
2. Vstupní připojení: Connect your power source (6V to 60V DC) to the 'IN' and 'GND' pads.
   • 'IN' is for the positive (+) input voltage.
   • 'GND' is for the negative (-) input voltage.
   • POZOR: This module does NOT have protection for reversed input polarity. Ensure correct polarity when connecting the power source to avoid damage to the BEC and connected components.
3. Výstupní připojení: Connect your devices requiring regulated power to the 'OUT' and 'G' pads.
   • 'OUT' provides the selected positive (+) output voltage (5V, 9V nebo 12V).
   • 'G' is the common ground (-) for the output.
4. Montáž: The compact size (18x15mm) and light weight (2g) allow for flexible mounting. Secure the module using appropriate methods for your application, ensuring it is protected from vibrations and physical damage.
5. Odvod tepla: While the module is rated for continuous current without an additional heat sink at room temperature (22°C), consider airflow or an external heat sink for applications with high continuous loads or in environments with elevated temperatures to ensure optimal performance and longevity.

4. Provoz

Once correctly installed and powered, the MBEC12S will provide a stable, regulated DC output voltage as selected. The module operates with a maximum duty cycle of 100%, meaning if the input voltage drops below the set output voltage, the regulator's output will follow the input voltage (e.g., if set to 12V output but input drops to 10V, the output will be 10V).

Monitor the continuous load current to stay within the specified limits for your input voltage to prevent overcurrent conditions and ensure stable operation. Refer to the "Continuous Load Current & Output Ripple" table in Section 2.1 for guidance.

5. Údržba

The MATEKSYS MBEC12S is a robust electronic component designed for reliability. Minimal maintenance is required:

• Keep the module clean and free from dust, dirt, and moisture.
• Nevystavujte modul extrémním teplotám nebo přímému slunečnímu záření po delší dobu.
• Regularly inspect solder joints and connections for any signs of wear or corrosion, especially in high-vibration environments.
• Ensure adequate airflow around the module, particularly during high-load operation, to prevent overheating.

6. Řešení problémů

• No Output Voltage:
  • Zkontrolujte vstupní objtage: Zajistěte vstupní hlasitosttage is within the 6V-60V range and above the 6.7V start-up voltage.
  • Check input polarity: Verify that the positive and negative input wires are connected correctly. Reversed polarity will damage the module.
  • Check connections: Ensure all solder joints and wires are securely connected to the BEC and the load.
• Nesprávný výstupní objemtage:
  • Verify solder bridge: Confirm that the correct solder pad (9V or 12V) is bridged for your desired output, or that no pads are bridged for 5V output. Ensure only one pad is bridged.
• Module Overheating / Intermittent Operation:
  • Reduce load: The module has Overcurrent Protection (OCP) and Thermal Shutdown. If it's overheating or shutting down, the load might be exceeding its continuous current capabilities. Refer to the specifications table.
  • Improve cooling: Ensure sufficient airflow. Consider adding a small heat sink if operating at high loads or in warm environments.
• Output Short-circuit:
  • The module is tolerant to output short-circuits for up to 3 seconds per minute. If a short occurs, disconnect power immediately, identify and resolve the short, then reconnect power. Prolonged short-circuits can damage the module.

7. Uživatelské tipy

• Pre-flight/Pre-use Check: Always double-check all wiring connections and polarity before applying power to prevent damage to the BEC and other electronic components.
• svtage Ověření: Pomocí multimetru ověřte výstupní hlasitosttage of the BEC before connecting it to your sensitive electronics, especially after adjusting the output voltage.
• Správa zatížení: Be mindful of the continuous current ratings. If your application requires higher currents, ensure adequate cooling or consider a BEC with higher current capabilities.
• Kvalita pájky: Use a fine-tipped soldering iron and good quality solder for bridging the voltage selection pads and connecting wires to ensure reliable electrical contact.

8. Záruka a podpora

For technical support, troubleshooting assistance, or warranty inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.