WenQia Universal Wireless Remote Control Switch

1. Úvod

This manual provides detailed instructions for the installation, operation, and maintenance of your WenQia Universal Wireless Remote Control Switch. This system consists of a DC 12V 4-channel relay receiver module and a 4-button RF remote control, designed for versatile applications in home automation, industrial control, and various DIY projects. Please read this manual thoroughly before use to ensure proper and safe operation.

2. Konec produktuview

The WenQia wireless remote control system allows you to wirelessly control up to four independent devices using a single remote. The receiver module features four relays, providing flexible control options for both AC and DC loads.

Figure 1: WenQia 4-channel relay receiver module and remote control.

2.1 Komponenty

• Modul přijímače: A circuit board with four relays, a learning button, an indicator light, and screw terminals for wiring. It is housed in a protective plastic enclosure.
• Dálkové ovládání: A compact 4-button (A, B, C, D) RF transmitter.

Figure 2: Labeled components of the receiver module.

Obrázek 3: Detailní view dvoutlačítkového dálkového ovladače.

3. Specifikace

Figure 4: Receiver module dimensions.

Figure 5: Remote control dimensions and battery information.

4. Bezpečnostní informace

• Ensure all power is disconnected before performing any wiring or installation.
• Do not exceed the maximum current (10A) or load (2200W) ratings of the receiver module.
• Handle electrical components with care to avoid electric shock.
• Udržujte zařízení mimo dosah vody a extrémních teplot.
• Only use the specified DC 12V power supply for the receiver module.
• Ensure proper insulation for all connections.

5. Nastavení a instalace

The receiver module has screw terminals for connecting the power supply and the devices to be controlled. The terminals are labeled NO (Normally Open), COM (Common), and NC (Normally Closed) for each of the four relays, along with DC 12V power input terminals.

5.1 Schémata zapojení

Refer to the following diagrams for common wiring configurations. Always ensure correct polarity for DC connections and proper insulation for all wiring.

Figure 6: Wiring for DC and AC devices (e.g., lights).

For DC Devices (e.g., DC 12V lights): Connect the DC 12V power supply to the receiver's DC 12V input terminals. For each device, connect one side to the positive (+) of the DC 12V supply and the other side to the COM terminal of a relay. Then, connect the NO terminal of that relay to the negative (-) of the DC 12V supply. When the relay is activated, the circuit closes, and the device turns on.

For AC Devices (e.g., AC 1V-250V lights): Connect the DC 12V power supply to the receiver's DC 12V input terminals. For each device, connect one side of the AC power line (e.g., Live) to the COM terminal of a relay. Connect the NO terminal of that relay to one terminal of your AC device. Connect the other terminal of your AC device to the Neutral line of your AC power supply. When the relay is activated, the circuit closes, and the device turns on.

Figure 7: Wiring for AC and DC motors (e.g., for automated curtains, garage doors).

For AC Motors (e.g., 1V-250V): This configuration typically uses two relays for forward/reverse or up/down control. Connect the DC 12V power supply to the receiver. Connect the AC power lines to the COM terminals of two relays. The NO terminals of these relays will connect to the motor's control inputs for 'Up' and 'Down' (or forward/reverse). Ensure interlocking mechanisms are in place to prevent both relays from activating simultaneously, which could damage the motor or power supply.

For DC Motors (e.g., DC 12V): Similar to AC motors, two relays are often used for directional control. Connect the DC 12V power supply to the receiver. Connect the DC 12V motor power to the COM terminals of two relays. The NO terminals will connect to the motor's positive and negative terminals, allowing for polarity reversal to change direction. Again, ensure only one relay is active at a time.

Anténa: Before use, gently stretch the antenna on the receiver board to optimize signal reception and range.

6. Návod k obsluze

The receiver module supports multiple operating modes, which determine how the relays respond to remote control button presses. These modes are Momentary, Toggle, Latched, and various Mix Modes. The remote control buttons (A, B, C, D) can be programmed to control the relays in these different modes.

6.1 Working Modes Explained

• Momentální režim: The relay turns ON only while the remote button is pressed and held. It turns OFF immediately upon release.
• Přepínací režim: Pressing the remote button once turns the relay ON. Pressing the same button again turns the relay OFF.
• Blokovaný režim: Pressing button 'A' turns relay 1 ON and keeps it ON. Pressing button 'B' turns relay 2 ON and turns relay 1 OFF. This mode typically uses multiple buttons to control a set of relays, where only one can be active at a time.
• Režim mixování: Combinations of Momentary, Toggle, and Latched modes can be set for different relays. For example, relays 1 and 2 could operate in Momentary mode, while relays 3 and 4 operate in Toggle mode.

6.2 Programming Remote Controls (How to Set Modes)

To program a remote control button to a specific mode, follow these steps using the 'Learning Button' on the receiver module:

Figure 8: Programming instructions for various operating modes.

• Momentální režim:
  1. Press the 'Learning Button' on the receiver module jednou. Kontrolka se rozsvítí.
  2. Press the desired button on your remote control (e.g., 'A'). The indicator light will flash and then turn off.
  3. Wait for 3 seconds. The programming is successful.
• Přepínací režim:
  1. Press the 'Learning Button' on the receiver module dvakrát. Kontrolka se rozsvítí.
  2. Press the desired button on your remote control (e.g., 'A'). The indicator light will flash and then turn off.
  3. Wait for 3 seconds. The programming is successful.
• Blokovaný režim:
  1. Press the 'Learning Button' on the receiver module 3krát. Kontrolka se rozsvítí.
  2. Press button 'A' on your remote control. The indicator light will flash.
  3. Press button 'B' on your remote control. The indicator light will flash again and then turn off.
  4. Wait for 3 seconds. The programming is successful. (Note: For 4-channel latched mode, you might need to press A, B, C, D in sequence depending on the specific implementation. The diagram shows A and B for two relays.)
• Mix Mode (e.g., Momentary for 1&2, Toggle for 3&4):
  1. Press the 'Learning Button' on the receiver module 4, 5, or 6 times depending on the specific mix mode desired (refer to Figure 8 for exact presses for different mix modes). The indicator light will turn on.
  2. Press the desired button on your remote control (e.g., 'A'). The indicator light will flash and then turn off.
  3. Wait for 3 seconds. The programming is successful.

6.3 Resetting Remote Controls

To clear all programmed remote controls from the receiver module:

• Press the 'Learning Button' on the receiver module 8krát. The indicator light will flash several times and then turn off.
• All previously stored remote control data will be deleted. After a reset, all remote controls will need to be reprogrammed.

7. Aplikační scénáře

This versatile remote control switch can be used in a wide range of applications, including:

Obrázek 9: Přamples of product applications.

• Domácí automatizace: Controlling lights, fans, automated curtains, water pumps, and other household appliances.
• Garage & Gate Control: Operating garage doors, electric gates, and road barriers.
• Průmyslové a komerční: Used in factories, offices, laboratories, and supermarkets for controlling various equipment and signal transmission.
• DIY projekty: Ideal for custom motor control (forward/reverse), electronic locks, and other remote-controlled systems.

8. Údržba

• Keep the receiver module and remote control dry and clean. Avoid exposure to moisture, dust, and corrosive substances.
• Nenechávejte zařízení upadnout na zem ani je nevystavujte silným nárazům.
• Replace the remote control battery (CR2016 3V) when its range decreases or it stops responding.
• Pravidelně kontrolujte, zda jsou kabelové spoje pevné a zda nevykazují známky opotřebení.

9. Řešení problémů

• Zařízení nereaguje na dálkové ovládání:
  • Check if the receiver module is powered correctly (DC 12V).
  • Ujistěte se, že baterie dálkového ovladače není vybitá.
  • Verify that the remote control is properly programmed to the receiver. If you recently performed a 'Reset', you will need to reprogram the remote.
  • Check for obstructions or excessive distance between the remote and receiver.
• Zmenšený dosah dálkového ovládání:
  • Gently stretch the antenna on the receiver board to improve signal reception.
  • Vyměňte baterii dálkového ovládání.
  • Ensure there are no strong RF interference sources nearby.
• Relay not activating/deactivating correctly:
  • Check all wiring connections to the device and the receiver module.
  • Ensure the load connected does not exceed the maximum current (10A) or power (2200W) rating.
  • Verify the operating mode is correctly set (Momentary, Toggle, Latched).
• Multiple remotes not working: If you performed a 'Reset' on the receiver, all previously paired remotes will be cleared. You must reprogram each remote individually.

10. Uživatelské tipy

• Více dálkových ovladačů: The receiver can store up to 25 remote controls. You can program multiple remotes to control the same receiver, which is useful for shared access (e.g., multiple users for a garage door).
• Přizpůsobení tlačítek: While the remote buttons are labeled A, B, C, D, their function (which relay they control and in what mode) is determined by the programming process. You can customize which button controls which relay and its operating mode.
• Optimalizace antény: For best performance, ensure the receiver's antenna is fully extended and positioned away from metal objects or other electronics that might cause interference.

11. Záruka a podpora

For any questions, technical assistance, or support regarding your WenQia Universal Wireless Remote Control Switch, please contact your seller or refer to the product listing for contact information. Please provide your model number (1204+KT16RF) and a detailed description of the issue when seeking support.