1. Úvod
This manual provides essential information for the installation, maintenance, and troubleshooting of your new replacement drive belt for Midea bread machines. Please read these instructions carefully before attempting any installation or repair to ensure safe and correct operation.
2. Bezpečnostní informace
- Always unplug the bread machine from the power outlet before attempting any inspection, maintenance, or replacement of parts.
- V případě potřeby používejte vhodné ochranné pomůcky, například rukavice.
- Udržujte malé části mimo dosah dětí.
- If you are unsure about any step, consult a qualified technician or refer to your bread machine's original service manual.
3. Konec produktuview
This is a replacement drive belt designed for various Midea bread machine models. The drive belt is a critical component that transfers power from the motor to the kneading paddle, ensuring proper mixing and kneading of dough.
Figure 1: Bread machine drive belt with '175T' marking, indicating 175 teeth.
Obrázek 2: Strana view of the bread machine drive belt.
4. Instalace (výměna)
Replacing the drive belt requires disassembling parts of your bread machine. Refer to your specific bread machine model's service manual for detailed disassembly instructions. The general steps are as follows:
- Unplug the Bread Machine: Ensure the appliance is completely disconnected from the power supply.
- Přístup k pohonnému mechanismu: Carefully disassemble the bottom or rear casing of your bread machine to expose the motor and drive belt assembly. This usually involves removing screws.
- Demontáž starého řemene: Once the drive mechanism is accessible, gently remove the old, worn, or broken belt from the motor pulley and the paddle shaft pulley. You may need to carefully pry it off.
- Nainstalujte nový řemen: Place the new belt (Model AE-HCDM167) onto the smaller motor pulley first. Then, stretch it over the larger paddle shaft pulley. Ensure the belt is seated correctly in the grooves of both pulleys. It should be snug but not excessively tight.
- Rotace testu: Manually rotate the paddle shaft to ensure the belt moves smoothly and without obstruction.
- Znovu sestavit: Carefully reassemble the bread machine casing, přičemž se ujistěte, že jsou všechny šrouby utažené a že nejsou přiskřípnuté žádné dráty.
- Počáteční test: Plug in the bread machine and run a short cycle (e.g., dough cycle) to confirm the new belt is functioning correctly.
5. Návod k obsluze
This drive belt is a component part of your bread machine. Once correctly installed, the operation of your bread machine will resume as per its original manufacturer's instructions. There are no specific operating instructions for the belt itself.
6. Údržba
To prolong the life of your bread machine drive belt:
- Pravidelná kontrola: Periodically inspect the belt for signs of wear, cracking, fraying, or stretching. This can be done during routine cleaning or if you notice changes in the bread machine's operation.
- Udržujte v čistotě: Ensure the area around the belt and pulleys is free from dough residue, flour, or other debris that could cause friction or damage.
- Vyhněte se přetížení: Do not overload your bread machine with ingredients beyond its recommended capacity, as this can put excessive strain on the drive belt.
7. Řešení problémů
If your bread machine is not functioning correctly after belt replacement, consider the following:
| Příznak | Možná příčina | Řešení |
|---|---|---|
| Kneading paddle not turning or turning slowly | Belt not properly seated on pulleys; Belt too loose; Motor issue (less likely if new belt) | Unplug, re-open, and ensure belt is correctly positioned and tensioned. If belt is correct, consult bread machine manual for motor diagnostics. |
| Skřípavý nebo vrzavý zvuk během provozu | Řemen se tře o casing; Pulleys misaligned; Debris in mechanism | Unplug, re-open, check for obstructions. Ensure pulleys are aligned and belt is not rubbing. Clean any debris. |
| Pálivý zápach | Belt friction; Motor overheating | Immediately unplug the machine. Check for belt rubbing or excessive tension. If smell persists, discontinue use and seek professional repair. |
8. Specifikace
| Atribut | Hodnota |
|---|---|
| Číslo modelu | AE-HCDM167 |
| Typ | Části pekárny na chleba |
| Délka | 525 mm |
| Šířka | 8 mm |
| Počet zubů | 175T |
| Compatible Midea Models | AHS15AB-PW, AHS20AB-PR, AHS15AC-PRS, AHS15AC-PGS, EHS15AP-PW, AHS20AC-PASY, AHS15AC-PAS, EHS15AP-PR, THS15BB-PW, EHS15AP-PY, AHS15AC-PRSY, AHS15AC-PY, AHS20AB-PT, EHS15AP-PG, THS20BB-PASY, EHS15AP-PWSY, EHS15AP-PGS, AHS20AB-PP, THS15BB-PARY, THS15BB-PGRY, EHS15Q3-PWRY, EHS15Q3-PRRY, EHS20Q3-PWRY, 260010600013, AHS20AB-PG, EHS15AP-PG, EHS15AP-PR |
9. Uživatelské tipy
- Ověřte kompatibilitu: Před nákupemasing, always double-check the model number and specifications (length, width, teeth count) of your old belt against this replacement part to ensure perfect fit.
- Jemné zacházení: When installing, avoid twisting or sharply bending the new belt, as this can damage its internal structure and reduce its lifespan.
- Čistota je klíčová: Ensure the pulleys are clean and free of grease or debris before installing the new belt to prevent premature wear.
10. Záruka a podpora
This replacement part is typically covered by the seller's or manufacturer's warranty for a limited period against manufacturing defects. Please retain your proof of purchase for any warranty claims. For specific warranty details or technical support, please contact the retailer or the part manufacturer directly.
