SINOTIMER SVP915-80A Nastavitelný nad/pod objemtagUživatelská příručka k ochrannému relé e

1. Konec produktuview

The SINOTIMER SVP915-80A is an automatic recovery over-voltage a pod-zvtage protective device designed to safeguard electrical equipment and personnel from unstable power situations. It complies with modular design standards and features high-quality electronic components for reliable performance. When the voltage exceeds or falls below the set limits, the device automatically cuts off the power. Once the voltage returns to normal, it will automatically re-supply power after a 30-second delay.

2. Funkce kláves

• Voltage ochrana
• Pod voltage ochrana
• Automatické obnovení
• Integrated Volt-meter display

3. Nastavení a instalace

3.1 Montáž

The SVP915-80A is designed for installation on a standard 35mm DIN rail. Ensure the device is securely clipped onto the rail in a suitable electrical enclosure.

3.2 Schéma zapojení

Proper wiring is crucial for safe and effective operation. Refer to the diagram below for connection instructions. Always ensure power is disconnected before performing any wiring.

Spojovací body:

• IN (Top Terminals): Connect the incoming Live (L) and Neutral (N) wires from your power source.
• OUT (Bottom Terminals): Connect the outgoing Live (L) and Neutral (N) wires to your electrical load or circuit.

Ujistěte se, že všechna připojení jsou pevná a bezpečná, abyste předešli uvolněným kontaktům a potenciálnímu nebezpečí.

4. Návod k obsluze

4.1 Počáteční zapnutí

Once correctly wired and mounted, apply power to the device. The integrated volt-meter display will show the current voltage. The device will perform a self-check and, if voltage is within safe limits, will supply power to the load after a 30-second delay.

4.2 Adjusting Protection Parameters

The SVP915-80A allows for adjustable over-voltage a pod-zvtage protection values. Use the 'SET', 'UP' (triangle), and 'DOWN' (inverted triangle) buttons on the front panel to configure these settings.

Chcete -li upravit nastavení:

1. Press and hold the 'SET' button until the display starts flashing, indicating entry into setting mode.
2. Use the 'UP' and 'DOWN' buttons to navigate through the different parameters (e.g., over-voltage protection value, over-voltage recovery value, under-voltage protection value, under-voltage recovery value, and protection action times).
3. When a parameter is selected, use the 'UP' and 'DOWN' buttons to adjust its value.
4. Press 'SET' again to confirm the value and move to the next parameter, or wait a few seconds for the device to automatically save the settings and exit setting mode.

Default and Adjustable Ranges:

• Voltage ochranná hodnota: Range 221V~290V~OFF (Default: 275V)
• Voltage využití svtage: Range 216V~285V (Default: 245V)
• Voltagdoba působení ochrany: Range 0.1s~3.0s (Default: 0.2s)
• Pod voltage ochranná hodnota: Range 219V~150V~OFF (Default: 170V)
• Pod voltage využití svtage: Range 155V~224V (Default: 185V)
• Pod voltagdoba působení ochrany: Range 0.1s~30s (Default: 0.2s)

4.3 Automatic Recovery

Po svtage anomaly (over or under voltage) causes the device to cut off power, it will automatically monitor the line voltagE. Jakmile se zvtage stabilizes within the acceptable range, the device will re-supply power to the load after a 30-second delay. This delay prevents rapid cycling and protects connected equipment.

5. Údržba

The SVP915-80A is designed for minimal maintenance. Periodically inspect the device and its connections for any signs of damage, loose wiring, or overheating. Ensure the area around the device is clean and free from dust or debris to maintain proper ventilation.

6. Řešení problémů

Pokud zařízení nefunguje podle očekávání, zvažte následující:

• Žádný displej/Žádné napájení: Check the incoming power supply and ensure all wiring connections are secure. Verify that the main circuit breaker supplying power to the device is ON.
• Časté vypínání zařízení: Voltage in your electrical system might be unstable. Monitor the voltage display to identify if it's consistently exceeding or falling below your set protection limits. Adjust the protection values if necessary, but ensure they are appropriate for your equipment.
• Device Does Not Recover: Zajistěte zvtage has returned to a stable level within the recovery range. The device has a 30-second recovery delay; wait for this period to elapse. If it still doesn't recover, check for persistent voltage problémy.
• Nesprávný svtage čtení: While rare, if you suspect the built-in voltmeter is inaccurate, compare its reading with a calibrated external voltmeter.

For persistent issues, contact qualified electrical personnel or the manufacturer's support.

7. Specifikace

8. Uživatelské tipy

• Nastavení testu: After adjusting protection values, it is recommended to simulate an over-voltage nebo pod-objtage condition (if safely possible with appropriate equipment) to verify the device trips and recovers as expected.
• Dokumentace: Uschovejte tento návod na bezpečném místě pro budoucí použití.
• Profesionální instalace: If you are unsure about electrical wiring, always consult a qualified electrician for installation to ensure safety and compliance with local regulations.

9. Záruka a podpora

For any technical assistance, warranty claims, or further information regarding your SINOTIMER SVP915-80A, please contact the official SINOTIMER store or your point of purchase. Ensure you have your product model number and purchase details ready when seeking support.

Manuals in English, Russian, and Portuguese may be available upon request from the seller.