Kenmore 97284100 Dryer Motor Replacement Part User Manual

1. Úvod

This manual provides essential information for the safe and correct installation, operation, and maintenance of the Fricpart-108109 replacement dryer motor, compatible with Kenmore 97284100 models. This component is designed to restore the functionality of your dryer by replacing a faulty original equipment manufacturer (OEM) motor. Please read these instructions thoroughly before proceeding with installation.

Obrázek 1.1: The Fricpart-108109 replacement dryer motor. This image displays the motor unit with its electrical connections and mounting points, ready for installation into a compatible dryer appliance.

2. Bezpečnostní informace

VAROVÁNÍ: Disconnect power to the dryer before servicing. Failure to do so can result in electrical shock, serious injury, or death. Appliance repair should only be performed by qualified individuals.

• Always unplug the dryer from the electrical outlet or turn off the circuit breaker before beginning any repair or maintenance.
• Používejte vhodné osobní ochranné prostředky (OOP), jako jsou rukavice a ochranné brýle.
• Ujistěte se, že pracovní prostor je dobře osvětlený a bez překážek.
• Udržujte děti a domácí zvířata mimo pracovní oblast.
• Handle electrical components with care.
• Verify that the replacement part is compatible with your dryer model before installation.

3. Nastavení a instalace

This section outlines the general steps for replacing a dryer motor. Specific disassembly and reassembly procedures may vary by dryer model. Refer to your dryer's service manual for detailed instructions.

3.1 Potřebné nástroje

• Šroubováky (Phillips a Flathead)
• Nut drivers or socket set
• Kleště
• Pracovní rukavice
• Ochranné brýle

3.2 kroky instalace

1. Odpojit napájení: Odpojte sušičku ze zásuvky nebo vypněte jistič, který sušičku napájí.
2. Přístup k motoru: Depending on your dryer model, you may need to remove the top panel, front panel, or rear panel to gain access to the motor compartment. This often involves removing screws and clips.
3. Propojení dokumentů: Before disconnecting any wires or components, take clear photos or make diagrams of all electrical connections and belt routing. This will aid in reassembly.
4. Remove the Drive Belt: Carefully remove the drive belt from the motor pulley and the drum.
5. Odpojit kabeláž: Disconnect all electrical wires connected to the old motor. Note their positions.
6. Demontáž starého motoru: Unbolt or unclip the old motor from its mounting brackets. Carefully remove it from the dryer.
7. Instalace nového motoru: Position the new Fricpart-108109 motor into the dryer and secure it with the mounting bolts or clips.
8. Připojení kabeláže: Reconnect all electrical wires to the new motor, referring to your photos or diagrams. Ensure connections are secure.
9. Znovu namontujte hnací řemen: Route the drive belt around the new motor pulley and the dryer drum according to your documentation. Ensure proper tension.
10. Znovu sestavte sušičku: Reattach all panels and components that were removed during disassembly. Ensure all screws and clips are securely fastened.
11. Obnovit napájení: Zapojte sušičku zpět do elektrické zásuvky nebo zapněte jistič.

4. Post-Installation Check and Operation

After installing the replacement motor, perform the following checks to ensure proper operation:

• Vizuální kontrola: Before starting the dryer, visually inspect all connections and ensure no tools or loose parts are left inside the appliance.
• Zkušební provoz: Start the dryer on a no-heat or air-fluff cycle. Listen for any unusual noises (grinding, squealing, humming) and observe if the drum rotates smoothly.
• Test tepelného cyklu: If the initial test is successful, run a short heat cycle to confirm proper heating and continued drum rotation.
• Kontrola ventilace: Ensure the dryer's exhaust vent is clear and unobstructed for efficient operation and to prevent overheating.

If any issues arise during these checks, refer to the Troubleshooting section.

5. Údržba

The Fricpart-108109 dryer motor is a sealed unit and does not require user maintenance. However, regular maintenance of your dryer appliance can prolong the life of all its components, including the motor.

• Čištění filtru na vlákna: Clean the lint filter before or after every load to maintain airflow and prevent motor strain.
• Kontrola odvětrávání: Periodically inspect and clean the dryer's exhaust vent system (ductwork) to prevent lint buildup, which can restrict airflow and cause the motor to work harder and overheat.
• Zkontrolujte překážky: Ensure no foreign objects are in the dryer drum or obstructing the blower wheel.

6. Řešení problémů

Pokud vaše sušička po výměně motoru nefunguje správně, zvažte následující běžné problémy:

Pokud kroky pro řešení potíží problém nevyřeší, doporučuje se obrátit se na kvalifikovaného technika pro opravu spotřebičů.

7. Specifikace

8. Záruka a podpora

Warranty coverage for this replacement part is typically provided by the seller or manufacturer at the time of purchase. Please refer to your purchase documentation or contact the seller directly for specific warranty terms and conditions.

For technical support or assistance with installation and troubleshooting beyond the scope of this manual, please contact the manufacturer, Fricparts, or the retailer from whom the part was purchased. Keep your purchase receipt and model information readily available.