VINGLI 24-inch Sand Pool Filter System with 1.5 HP Pump Instruction Manual

Zavedení

This manual provides essential information for the safe installation, operation, and maintenance of your VINGLI 24-inch Sand Pool Filter System with a 1.5 HP Pump. Please read all instructions carefully before installation and use to ensure proper function and longevity of your equipment. This system is designed for efficient filtration of above-ground and in-ground swimming pools up to 22,000 gallons.

Image: The VINGLI 24-inch Sand Pool Filter System, illustrating its powerful filtration capability with water flow indicators.

Bezpečnostní informace

VAROVÁNÍ: Failure to follow these instructions can result in serious injury or death. Always observe basic safety precautions when installing and operating this equipment.

• Před servisem odpojte napájení.
• Ensure the system is installed by a qualified professional in accordance with local codes.
• Nepoužívejte systém, pokud je některá jeho část poškozena.
• Udržujte děti mimo dosah zařízení.
• Nikdy nepoužívejte čerpadlo na sucho.
• Maintain proper water chemistry in your pool.
• Always relieve pressure in the filter tank before opening the multi-port valve or performing maintenance.

Seznam komponent

Před zahájením instalace ověřte, zda jsou všechny komponenty přítomny:

• Písková filtrační nádrž (24 palců)
• 1.5 HP Pool Pump (115V)
• Vícecestný ventil
• Filtrační koš
• Tlakoměr
• Připojení hadic a Clamps
• Základní deska
• Uživatelská příručka

Nastavení

1. Umístění

Position the filter system on a firm, level surface, preferably concrete, as close to the pool as possible. Ensure adequate ventilation and protection from direct sunlight and harsh weather. Maintain sufficient clearance around the unit for servicing.

2. Montáž

1. Attach the pump to the base plate.
2. Place the filter tank onto the base plate.
3. Connect the multi-port valve to the top of the filter tank. Ensure the O-ring is properly seated and secure the clamp.
4. Install the pressure gauge into the designated port on the multi-port valve.

3. Přidání filtračního média

The VINGLI filter system is compatible with both filter sand and filter balls. For optimal performance, use #20 silica sand (0.45-0.55mm) or approved filter balls.

1. Remove the multi-port valve from the tank.
2. Zakryjte otvor stoupací trubky uvnitř nádrže, abyste zabránili vniknutí písku.
3. Carefully pour the filter media into the tank. Refer to the specifications table for the recommended amount of sand.
4. Remove the standpipe cover and re-attach the multi-port valve.

Image: Illustration demonstrating that both sand and filter balls can be used as filter media in the system.

4. Instalatérské připojení

Connect the pool plumbing to the multi-port valve and pump:

• Connect the hose from the pool skimmer/main drain to the pump's inlet (suction side).
• Connect the pump's outlet (discharge side) to the "PUMP" port on the multi-port valve.
• Connect the "RETURN" port on the multi-port valve to the pool's return line.
• Connect the "WASTE" port on the multi-port valve to a suitable waste line or backwash hose.

Image: The VINGLI filter system installed next to an above-ground pool, showing hose connections.

Image: The VINGLI filter system installed next to an in-ground pool, showing hose connections.

Návod k obsluze

Vícecestný ventil řídí průtok vody filtračním systémem. Před změnou polohy ventilu vždy vypněte čerpadlo, abyste předešli poškození.

Image: The multi-port valve highlighting its six operational functions.

• FILTR: Normal filtering mode. Water flows through the sand bed, trapping debris, and returns to the pool.
• BACKWASH: Cleans the filter by reversing water flow, flushing trapped debris out the waste port.
• MÁCHÁNÍ: Used after backwashing to flush residual dirt from the valve and sand bed to the waste port, preventing it from returning to the pool.
• ODPAD: Bypasses the filter, sending water directly from the pool to the waste port. Useful for vacuuming heavy debris or lowering pool water level.
• RECIRCULOVAT: Obchází filtr a cirkuluje vodu přímo zpět do bazénu. Vhodné pro míchání chemikálií bez filtrace.
• ZAVŘENO: Shuts off all flow to the filter and pump. Do not operate the pump in this position.

Initial Startup and Backwash

1. Ensure all connections are secure and the pool is filled to the proper level.
2. Prime the pump by filling the pump basket with water if it's not self-priming.
3. Nastavte vícecestný ventil do polohy „ZPĚTNÉ PROPLACHOVÁNÍ“.
4. Turn on the pump. Backwash for 2-3 minutes or until the water in the sight glass (if present) runs clear.
5. Vypněte čerpadlo.
6. Nastavte vícecestný ventil do polohy „PROPLÁCH“.
7. Zapněte čerpadlo. Proplachujte 30–60 sekund.
8. Vypněte čerpadlo.
9. Nastavte vícecestný ventil do polohy „FILTER“.
10. Turn on the pump. The system is now operating in normal filtration mode.

Údržba

Pravidelné zpětné proplachování

Backwash the filter when the pressure gauge reads 8-10 PSI above its clean operating pressure, or when water flow to the pool noticeably decreases. Follow the "Initial Startup and Backwash" procedure.

Výměna filtračního média

Filter sand typically needs replacement every 3-5 years, depending on usage and water chemistry. Filter balls may last longer but should be inspected annually.

Zazimování

Before freezing temperatures arrive, drain all water from the pump and filter tank. Disconnect hoses and store the pump and multi-port valve in a dry, protected area. The filter tank can remain outdoors if completely drained.

Odstraňování problémů

Specifikace

Image: Detailed specifications table for various VINGLI sand filter sizes, including recommended pool size, flow rate, pump horsepower, and sand requirements.

Záruka a podpora

For warranty information, technical support, or to purchase replacement parts, please contact VINGLI customer service. Refer to your purchase documentation for specific warranty terms and contact details.

You can also visit the official VINGLI store for more information: VINGLI Store on Amazon