LEDOne Corp LED Wall Pack Instruction Manual

1. Úvod

This manual provides comprehensive instructions for the installation, operation, and maintenance of the LEDOne Corp Multi-Watt LED Wall Pack. This fixture is designed for demanding outdoor lighting applications, offering selectable wattage (80W, 100W, 120W) and adjustable color temperature (3000K, 4000K, 5000K) to meet various lighting requirements efficiently.

2. Bezpečnostní informace

WARNING: Risk of electric shock. Installation must be performed by a qualified electrician in accordance with all national and local electrical codes.

• Před instalací nebo servisem odpojte napájení jističem.
• Zajistěte přívod objtagje kompatibilní s provozním objemem svítidlatage (120-277V).
• Nemanipulujte se svítidly pod napětím mokrýma rukama nebo pokud stojíte na mokrém či suchém povrchu.amp povrchy.
• Use only UL/ETL approved components and wiring methods.
• Ujistěte se, že je svítidlo bezpečně upevněno, aby nedošlo k jeho pádu.
• Nedívejte se přímo do LED světelného zdroje, když je rozsvícený.

3. Obsah balení

Před zahájením instalace ověřte, zda jsou všechny komponenty přítomny:

• LEDOne Corp LED Wall Pack Fixture
• Návod k použití (tento dokument)
• Montážní hardware

4. Specifikace

5. Nastavení a instalace

The LEDOne Corp Wall Pack is designed for wall mounting and compatibility with standard junction boxes. Follow these steps for secure installation:

1. Příprava: Ensure power is disconnected at the circuit breaker. Gather necessary tools (screwdriver, wire strippers, drill, mounting hardware).
2. Místo montáže: Select a suitable wall surface capable of supporting the fixture's weight (approximately 10.63 lbs). The fixture features reinforced mounting points.
3. Montážní držák: Attach the wall mount bracket (if separate) or position the fixture directly over the junction box. Mark and drill pilot holes for the mounting screws.
4. Bezpečné upevnění: Secure the fixture to the wall using the provided mounting hardware. Ensure it is firmly attached and level.
5. Zapojení: Open the wiring compartment. Connect the fixture's wires to the supply wires from the junction box:
   • Černý vodič k linkě (L)
   • Bílý vodič k nule (N)
   • Green wire to Ground (G)
   Use the provided waterproof wire nuts for secure outdoor connections. For 0-10V dimming, connect the purple wire to DIM+ and the gray wire to DIM-.
6. Zavřít přihrádku: Carefully tuck all wires into the junction box and wiring compartment. Close and seal the compartment cover to maintain IP65 rating.
7. Zapnutí: Obnovte napájení jističe a otestujte přípravek.

Obrázek 1: Zadní strana view of the LED wall pack, illustrating the mounting points and the central access for electrical wiring connections.

Obrázek 2: Boční profesionálfile of the LED wall pack, showing the robust construction and a visible screw for secure mounting.

6. Návod k obsluze

The LEDOne Corp Wall Pack features adjustable wattage and color temperature settings, typically controlled by internal switches. These switches are usually located within the wiring compartment or on the side of the LED driver housing, accessible after opening the fixture.

Obrázek 3: Přední strana view of the LED wall pack with the protective lens removed, revealing the array of LED chips and the internal switches for adjusting wattage a CCT.

1. Nastavení Wattage:
   • Ensure power is disconnected before opening the fixture.
   • Najděte wattage selection switch (often labeled WATT or POWER).
   • Vyberte požadovaný wattage: 80 W, 100 W nebo 120 W.
   • Close the fixture securely before restoring power.
2. Adjusting Color Temperature (CCT):
   • Ensure power is disconnected before opening the fixture.
   • Locate the CCT selection switch (often labeled CCT or TEMP).
   • Select the desired color temperature: 3000K (warm white), 4000K (cool white), or 5000K (daylight).
   • Close the fixture securely before restoring power.
3. 0-10V Stmívání: This fixture supports 0-10V dimming. Connect a compatible 0-10V dimmer to the purple (DIM+) and gray (DIM-) wires during installation.
4. Photocell/Motion Sensor: The fixture may include or be compatible with external photocells or motion sensors for automated operation. Refer to the specific sensor's instructions for integration.

Obrázek 4: Úhlové view of the LED wall pack, showcasing its complete assembly and the illuminated LED array.

7. Údržba

The LEDOne Corp Wall Pack is designed for minimal maintenance. Regular inspection and cleaning will ensure optimal performance and longevity.

• Čištění: Periodically clean the outer lens and housing with a soft, damp cloth to remove dirt, dust, and debris. Do not use abrasive cleaners or solvents. Ensure power is off before cleaning.
• Inspekce: Annually inspect the fixture for any signs of physical damage, loose connections, or wear on the wiring. Address any issues promptly.
• těsnění: Ensure all seals and gaskets are intact to maintain the IP65 weatherproof rating.

8. Řešení problémů

Pokud zařízení nefunguje správně, podívejte se na následující běžné problémy a jejich řešení:

If troubleshooting steps do not resolve the issue, contact LEDOne Corp customer support.

9. Informace o záruce

The LEDOne Corp Multi-Watt LED Wall Pack is backed by a comprehensive 5-letá záruka. This warranty covers defects in materials and workmanship under normal use and service. For warranty claims or detailed terms and conditions, please contact LEDOne Corp customer support.

10. Podpora a kontakt

For further assistance, technical support, or inquiries regarding your LEDOne Corp product, please visit the official LEDONE Store or contact customer service:

Visit the LEDONE Store on Amazon