Valkyrie A360 ARGB All-in-One CPU Liquid Cooler User Manual

1. Úvod

This manual provides detailed instructions for the installation, operation, and maintenance of your Valkyrie A360 ARGB All-in-One (AIO) CPU Liquid Cooler. Please read this manual thoroughly before installation to ensure proper setup and optimal performance. Keep this manual for future reference.

2. Bezpečnostní informace

• Před instalací se ujistěte, že je počítačový systém vypnutý a odpojený ze zásuvky.
• Handle components with care to avoid damage. Avoid touching the cold plate surface directly.
• Do not open the liquid cooler's pump or radiator; it is a sealed unit. Tamptím dojde ke ztrátě záruky.
• Keep the product away from extreme temperatures, humidity, and direct sunlight.
• Use only the provided mounting hardware to prevent damage to your CPU or motherboard.

3. Obsah balení

Ověřte, zda jsou v balení přítomny všechny níže uvedené komponenty:

• Valkyrie A360 ARGB AIO Liquid Cooler (Radiator, Pump/CPU Block, Tubing)
• 3 x 120mm ARGB ventilátory
• Intel Mounting Bracket Kit (LGA 1700, 1200, 115X, 2066, 2011)
• Sada montážních držáků AMD (AM5, AM4)
• Fan Screws and Radiator Mounting Screws
• Teplovodní pasta (předem nanesená nebo v tubě)
• ARGB Controller/Cables (if included)
• Uživatelská příručka

Image: The Valkyrie A360 ARGB AIO Liquid Cooler showing the radiator, three ARGB fans, and the pump/CPU block unit.

4. Nastavení a instalace

4.1. Příprava

• Vypněte počítač a odpojte všechny kabely.
• Open your computer case to access the motherboard and CPU area.
• If replacing an existing cooler, carefully remove it and clean any old thermal paste from the CPU surface using isopropyl alcohol.

4.2. Instalace chladiče a ventilátoru

1. Attach the three 120mm ARGB fans to the radiator using the long fan screws provided. Ensure the fan airflow direction is appropriate for your case (typically exhausting air out or pulling air in).
2. Mount the assembled radiator and fans to an available 360mm mounting location in your PC case (e.g., top, front). Use the shorter radiator mounting screws.

Image: The radiator with three white fans attached, ready for case installation.

4.3. Instalace bloku CPU

1. Pro patice Intel: Install the appropriate Intel backplate behind the motherboard. Attach the Intel mounting standoffs to the motherboard.
2. Pro patice AMD: Remove the stock AMD retention brackets from the motherboard, but keep the original backplate. Attach the AMD mounting standoffs to the motherboard.
3. If thermal paste is not pre-applied to the cold plate, apply a small pea-sized amount to the center of your CPU's Integrated Heat Spreader (IHS).
4. Carefully place the CPU block onto the CPU, aligning the mounting holes with the standoffs.
5. Secure the CPU block with the thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.

Obrázek: Detailní záběr view of the Valkyrie A360 CPU block installed on a motherboard, illuminated with blue ARGB lighting.

4.4. Připojení kabelů

1. Connect the pump's 3-pin or 4-pin power cable to the motherboard header labeled "AIO_PUMP," "CPU_OPT," or "SYS_FAN" (consult your motherboard manual for the recommended header).
2. Connect the ARGB cables from the fans and pump to the included ARGB controller or directly to a 5V 3-pin ARGB header on your motherboard. Ensure correct pin alignment to avoid damage.
3. Connect the fan power cables to available fan headers on your motherboard or to a fan hub/controller.

Image: The Valkyrie A360 AIO cooler fully installed within a white PC case, showcasing the blue ARGB lighting on the fans and CPU block.

5. Návod k obsluze

5.1. Počáteční zapnutí

After completing the installation, close your PC case, reconnect all external cables, and power on your computer. Observe the cooler for any unusual noises or leaks. Check your system's BIOS/UEFI for CPU temperature readings to confirm proper operation.

5.2. Ovládání osvětlení ARGB

If connected to a motherboard's 5V 3-pin ARGB header, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync). If using the included ARGB controller, refer to its specific instructions for mode and color selection.

Image: The Valkyrie A360 AIO cooler installed in a white PC case, displaying vibrant rainbow ARGB lighting effects on the fans and CPU block.

6. Údržba

• Čištění prachu: Periodically clean the radiator fins and fan blades to prevent dust buildup, which can impede airflow and cooling performance. Use compressed air or a soft brush.
• Vizuální kontrola: Regularly check the tubing and connections for any signs of leaks or damage.
• No Coolant Refill: The Valkyrie A360 is a sealed AIO unit and does not require coolant refills. Opening the unit will void the warranty.

7. Řešení problémů

8. Specifikace

9. Záruka a podpora

Valkyrie products are backed by a limited warranty against defects in materials and workmanship. The specific warranty period may vary by region. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please visit the official Valkyrie webnebo kontaktujte jejich oddělení zákaznických služeb. Kontaktní informace obvykle naleznete na obalu produktu nebo na oficiálních stránkách webmísto.

Note: Opening the sealed AIO unit or using non-approved components may void your warranty.