PHYSEN JKD-514COM-W 2-in-1 WLAN Smoke and CO Detector

1. Úvod

Thank you for choosing the PHYSEN JKD-514COM-W 2-in-1 WLAN Smoke and Carbon Monoxide Detector. This device is designed to provide early warning of both smoke and carbon monoxide (CO) hazards in your home or office. It features a high-precision LCD digital display, a test button, and connects to your 2.4 GHz WiFi network for app notifications. Please read this manual thoroughly before installation and use to ensure proper operation and safety.

2. Důležité bezpečnostní informace

• This detector is designed for indoor use only.
• Do not paint the detector. Paint can clog the sensing chambers and prevent the unit from operating correctly.
• Do not install in areas with high humidity, excessive dust, or insect infestation.
• Regularly test the detector as described in the Maintenance section.
• Nikdy neignorujte alarm. Okamžitě zjistěte jeho příčinu.
• This device is not a substitute for proper ventilation and maintenance of fuel-burning appliances.

3. Konec produktuview

The PHYSEN JKD-514COM-W detector combines photoelectric smoke sensing and electrochemical CO sensing in one compact unit. It provides continuous monitoring and alerts you to potential dangers.

Obrázek 1: Přední strana view of the PHYSEN JKD-514COM-W 2-in-1 WLAN Smoke and CO Detector, showing the LCD screen and test button.

Klíčové komponenty:

• Digitální LCD displej: Shows battery level and CO concentration in PPM.
• Tlačítko Test/Ztišit: Používá se k testování alarmu a umlčení falešných poplachů.
• Stavové kontrolky LED: Green for normal operation, Red for alarm status.
• Bzučák: Emits a loud 85 dB alarm sound.

4. Nastavení a instalace

4.1 Instalace baterie

1. Remove the mounting bracket by twisting the detector counter-clockwise.
2. Otevřete kryt bateriového prostoru.
3. Insert two 1.5V AA alkaline batteries, ensuring correct polarity (+ and -).
4. Close the battery compartment cover. The detector will emit a short beep and the green LED will flash, indicating it is powered on.

4.2 Výběr místa montáže

For optimal protection, install detectors in all sleeping areas and on every level of your home. Consider the following:

• Detekce kouře: Mount on the ceiling in the center of a room or at least 10 cm (4 inches) from a wall. Avoid corners.
• CO Detection: Install at breathing height, typically 1.5 meters (5 feet) from the floor.
• Avoid installing near windows, doors, or vents where drafts could affect readings.
• Keep away from cooking appliances, bathrooms, and areas with high humidity.

4.3 Montáž detektoru

1. Pomocí montážního držáku jako šablony si označte dva otvory pro vrtání na zdi nebo stropě.
2. Drill the holes and insert the provided wall plugs.
3. Pevně ​​přišroubujte montážní držák na místo.
4. Align the detector with the mounting bracket and twist clockwise until it locks securely.
5. Perform a test by pressing the Test/Silence button.

5. WLAN (Wi-Fi) Connection and App Setup

The detector connects to your 2.4 GHz WiFi network via the "Smart Life" or "Tuya" app for remote monitoring and notifications.

1. Stáhněte si aplikaci: Hledat "Smart Life" or "Tuya Smart" in your smartphone's app store (iOS or Android) and install it.
2. Registrace/Přihlášení: Otevřete aplikaci a vytvořte si účet nebo se přihlaste, pokud jej již máte.
3. Přidat zařízení: Tap the "+" icon or "Add Device" in the app. Select "Security & Video Surveillance" > "Smoke Detector (Wi-Fi)" or "CO Detector (Wi-Fi)".
4. Zadejte podrobnosti o Wi-Fi: Ensure your phone is connected to a 2.4 GHz Wi-Fi network. Enter your Wi-Fi password in the app.
5. Režim párování: On the detector, press and hold the Test/Silence button for 5-10 seconds until the LED indicator flashes rapidly. Confirm this in the app.
6. Připojit: The app will search for and connect to the detector. Once connected, you can name the device (e.g., "Living Room Smoke/CO Detector") for easy identification of alarm sources.
7. Sdílet zařízení: You can share access to the detector with up to 12 family members or friends through the app, allowing them to receive alarm notifications.

6. Provoz

6.1 Normální provoz

During normal operation, the green LED indicator will flash approximately every 40 seconds, and the LCD will display the current battery level and CO concentration (if any) in PPM. A new measurement is carried out every 40 seconds.

6.2 Podmínky alarmu

• Kouřový alarm: The red LED will flash rapidly, and the buzzer will emit a loud, continuous alarm sound. The app will send an immediate notification.
• Detektor oxidu uhelnatého (CO): The red LED will flash rapidly, and the buzzer will emit a series of short beeps. The LCD will display the detected CO level. If the CO value exceeds 200 ppm, an alarm will be sent via the app.
• Upozornění na vybitou baterii: The detector will chirp periodically, and the LCD will show a low battery icon. Replace batteries immediately.
• Varování před poruchou: The detector constantly monitors itself. If a malfunction is detected, it will indicate an error, and the app will notify you.

6.3 Testovací funkce

Press and hold the Test/Silence button for a few seconds. The detector will sound the alarm and flash the red LED, confirming that its electronic circuitry, horn, and battery are working. Release the button to stop the test.

6.4 Funkce ztišení

In case of a non-emergency alarm (e.g., cooking smoke), you can temporarily silence the alarm by pressing the Test/Silence button. The alarm will silence for a short period (typically 5-10 minutes) before re-evaluating the air quality. If the hazard persists, the alarm will reactivate.

7. Údržba

7.1 Pravidelné testování

Test your detector weekly by pressing the Test/Silence button. If the alarm does not sound, replace the batteries or contact support.

7.2 Čištění

Clean the detector at least once a month to remove dust and debris. Use a soft, damp cloth to wipe the exterior. Do not use cleaning sprays or solvents. You may also use a vacuum cleaner with a soft brush attachment to gently clean around the vents.

7.3 Výměna baterie

When the low battery warning sounds (periodic chirp and low battery icon on LCD), replace both 1.5V AA alkaline batteries immediately. Refer to section 4.1 for battery installation steps.

7.4 End-of-Life Indication

The detector has a sensor life of 10 years. After this period, the unit will indicate its end-of-life, and it should be replaced to ensure continued protection.

8. Řešení problémů

9. Specifikace

• Model: JKD-514COM-W
• Typ senzoru: Fotoelektrické (kouř), elektrochemické (CO)
• Zdroj napájení: 2 x 1.5V AA alkalické baterie
• Hlasitost alarmu: 85 dB at 3 meters
• CO Detection Range: 0-999 PPM
• Provozní teplota: 0 °C až 40 °C (32 °F až 104 °F)
• Provozní vlhkost: 0% až 95% RH (bez kondenzace)
• Rozměry: 10.5 x 10.5 x 3.85 cm (4.13 x 4.13 x 1.52 palce)
• Hmotnost: Approximately 500 g (0.5 kg)
• certifikace: EN14604, EN50291
• Životnost senzoru: 10 roky

10. Záruka a podpora

The PHYSEN JKD-514COM-W detector is designed for a long service life, with a sensor life of 10 years. For technical support, troubleshooting assistance, or warranty inquiries, please refer to the contact information provided with your purchase or visit the official PHYSEN website. Always ensure you have your model number (JKD-514COM-W) and purchase details ready when contacting support.