INJORA Aluminum Oil Shocks Instruction Manual

1. Úvod

This manual provides essential information for the installation, operation, and maintenance of your INJORA Aluminum Oil Shocks. These high-quality shocks are designed to enhance the performance and durability of your Losi 1/24 Micro-B and 1/28 Micro-T RC buggies. Please read these instructions carefully before proceeding with installation or use.

Figure 1: INJORA Aluminum Oil Shocks (Front View)

2. Obsah balení

Ověřte, zda jsou v balení přítomny všechny komponenty:

• 2 x Front Aluminum Oil Shocks
• 2 x Rear Aluminum Oil Shocks
• 2 x Short Front Springs (0.45mm, 8T)
• 2 x Long Rear Springs (0.4mm, 10T)
• Assorted mounting hardware (screws, nuts, spacers)

Obrázek 2: Kompletní obsah balení

3. Specifikace

4. Nastavení a instalace

Proper setup is crucial for optimal performance. These oil-filled shocks require initial filling with shock oil (not included) and careful assembly.

4.1 Shock Oil Filling

The shocks are shipped without oil or with minimal oil. It is essential to fill them with appropriate weight shock oil for your specific driving conditions and desired damping characteristics. Refer to the exploded view pro identifikaci komponent.

• Disassemble the shock by carefully removing the top cap and spring.
• Slowly fill the shock body with your chosen shock oil, ensuring no air bubbles are trapped.
• Gently move the shock shaft up and down to release any trapped air. Allow the shock to sit for a few minutes to let air bubbles rise.
• Top off the oil if necessary, ensuring the oil level is just above the piston when the shaft is fully compressed.
• Reinstall the top cap, being careful not to overtighten. The excess oil will be pushed out.
• Test the shock's movement for smooth, consistent dampIng.

Obrázek 3: Rozložené View of Front and Rear Shocks

4.2 Pre-load Adjustment

The shocks feature threaded bodies for quick pre-load adjustments. Rotate the threaded collar on the shock body to compress or decompress the spring, adjusting the ride height and stiffness of your RC buggy.

4.3 Installation on Vehicle

Mount the shocks to your Losi Micro-B or Micro-T buggy using the provided hardware. Ensure all screws are securely fastened but do not overtighten to avoid damaging components. The nylon bottom rod ends offer flexibility during installation and use.

Figure 4: Shocks Installed on RC Buggy

5. Provozní aspekty

Once installed and properly filled, your INJORA Aluminum Oil Shocks will provide improved damping and handling for your RC buggy. Experiment with different shock oil viscosities and spring pre-load settings to fine-tune performance for various terrains and driving styles.

6. Údržba

Oil-filled shocks require regular maintenance to ensure consistent performance and longevity. The shock oil can break down or become dirty over time, affecting dampvlastnosti.

• Pravidelná kontrola: Periodically check the shocks for leaks, bent shafts, or damaged rod ends.
• Výměna oleje: Replace the shock oil as needed, especially after heavy use or if performance degrades. The frequency depends on usage and environment.
• Čištění: Keep the shock shafts clean to prevent dirt and debris from entering the shock body and contaminating the oil or damaging seals.

7. Řešení problémů

• Inconsistent Damping: This is often caused by air bubbles in the shock oil or insufficient oil. Re-bleed and refill the shocks as described in Section 4.1.
• Leaking Oil: Check for damaged O-rings or seals. Ensure the top cap is securely tightened. Replace worn components if necessary.
• Nerovnoměrná výška jízdy: Verify that the spring pre-load is set equally on both sides (front and rear). Also, check for bent shock shafts or damaged springs.

8. Záruka a podpora

For warranty information or technical support, please refer to the official INJORA webnebo se obraťte na prodejce. Uschovejte si doklad o koupi pro případné reklamace.