How do I set up the PHYSEN Fingerprint Door Lock (MMS-1-US-B)?

To set up the PHYSEN MMS-1-US-B Fingerprint Door Lock, follow these installation and initial configuration steps:1. Door Compatibility CheckEnsure your door thickness is between 1-3/8" and 2" (35-55mm).The backset should be 2-3/8" or 2-3/4" (60mm or 70mm).The lock is compatible with standard left and right-handed single-cylinder doors but not mortise systems.2. Physical InstallationInstall the Latch: Insert the adjustable latch into the door edge in the unlocked position.Exterior Assembly: Place the keypad unit through the door hole, aligning it with the latch.Interior Assembly: Route the cables carefully and connect the interior unit to the exterior assembly. Secure it with the provided screws.Attach Handles: Install the lever handles on both sides.Power On: Insert 4 AA alkaline batteries into the interior battery compartment.3. Programming and OperationFingerprint Registration: The sensor can store up to 100 fingerprints. Follow the specific voice or light prompts in your printed manual to enter programming mode and scan your finger.Keypad Codes: You can set up to 100 user codes. The lock supports "anti-peeping," allowing you to enter random digits before or after your real code.Auto-Lock: You can configure the lock to automatically engage after 5-99 seconds or use the one-touch lock button on the keypad.Silent Mode: If you prefer no beeping during use, you can activate silent mode via the keypad settings.Note: If the lock is unresponsive, ensure the batteries are fresh and correctly oriented. Always keep the two included mechanical backup keys in a safe place outside the home for emergency access.

How do I reset the PHYSEN Fingerprint Door Lock (MMS-1-US-B)?

While the provided manual text for the PHYSEN MMS-1-US-B describes installation and general operation, it does not explicitly list a specific button-press sequence for a factory reset. However, based on standard smart lock procedures for this type of biometric deadbolt, you can typically reset the device using one of the following methods:Reset Button: Look for a small reset button or pinhole located on the interior assembly (often behind the battery cover or near the bottom of the unit). Press and hold this button for approximately 5 to 10 seconds until you hear a beep or see the keypad light up, indicating the lock has returned to factory settings.Battery Pull Reset: Some models require you to remove one battery, hold the 'Reset' button, and reinsert the battery while continuing to hold the button until a confirmation tone sounds.Important Note: Performing a factory reset will delete all registered fingerprints (up to 100) and user codes. After resetting, you will need to follow the initial setup instructions to register the administrator fingerprint and new user codes. If these steps do not work, please refer to the physical paper manual included in your box or contact PHYSEN customer support through their official Amazon store for the specific key combination.

The PHYSEN MMS-1-US-B lock is blinking red and green and does not lock or unlock from the keypad. How do I fix this?

When a PHYSEN MMS-1-US-B smart lock blinks red and green and fails to operate via the keypad, it typically indicates a power issue or a system lockout. Please try the following steps to resolve the issue:Check for Low Battery: The most common cause for blinking indicators and unresponsiveness is low battery power. Replace all 4 AA batteries with brand-new alkaline batteries simultaneously. Do not mix old and new batteries.Check for System Lockout: If too many incorrect codes or fingerprints were attempted, the system may be in a security lockout mode. This usually lasts for 3 minutes. During this time, the keypad will be unresponsive. Wait for the period to expire and try again.Inspect Cable Connections: If the batteries are new, the issue may be a loose connection between the exterior keypad and the interior assembly. Remove the interior battery cover and ensure the data cable is securely plugged in and has not been pinched during installation.Use Backup Keys: If the electronic components remain unresponsive, use the provided mechanical backup keys to manually unlock the door to gain entry.Reset the Lock: If the blinking persists, refer to your physical manual for the reset button location (usually found inside the battery compartment) to restore the lock to factory settings and re-program your codes.

PHYSEN Keyless Entry Fingerprint Door Lock with 2 Lever Handles User Manual

Zavedení

The PHYSEN Keyless Entry Fingerprint Door Lock offers advanced security and convenience for your home or office. This smart deadbolt set provides multiple unlocking methods, including fingerprint recognition, keypad codes, and traditional mechanical keys. Designed for easy installation and durable performance, it ensures reliable access control and peace of mind.

Komponenty skončilyview

Your PHYSEN Keyless Entry Fingerprint Door Lock package includes all necessary components for installation and operation:

Keyless entry door lock unit
2 pákové rukojeti
Adjustable latch (x2)
Setup assembly kits (screws, plates, etc.)
2 Backup keys

PHYSEN Keyless Entry Fingerprint Door Lock components

Image: All components included in the PHYSEN Keyless Entry Fingerprint Door Lock package.

Multiple ways to lock and unlock the PHYSEN door lock

Image: Visual representation of the multiple unlocking methods: fingerprint, password, spare keys, one-time password, auto-lock, and low battery alert.

Nastavení a instalace

The PHYSEN Keyless Entry Fingerprint Door Lock is designed for easy self-installation, typically requiring only a screwdriver. It is compatible with all American standard left and right-handed doors.

Kontrola kompatibility dveří

Před instalací se ujistěte, že vaše dveře splňují následující specifikace:

Door Hole: 2-1/8 palce (54 mm)
Minimalist Distance: ≥ 4 inches (101.6mm)
Zadní část: 2-3/8 inches or 2-3/4 inches (60mm or 70mm)
Otvor pro západku: 1 palců (25 mm)
Tloušťka dveří: 1-3/8 inches to 2 inches (35-55mm)

The lock is suitable for single cylinder doors and is not compatible with mortise or integrated lock systems.

Door size compatibility diagram for PHYSEN lock

Image: Diagram illustrating required door dimensions and compatibility for installation.

Kroky instalace

Připravte dveře: Remove any existing deadbolt hardware. Ensure the latch is in the unlocked position before proceeding.
Nainstalujte západku: Insert the adjustable latch into the door edge.
Instalace vnější sestavy: Place the exterior keypad assembly through the door hole, aligning it with the latch.
Instalace vnitřní sestavy: Connect the interior assembly to the exterior assembly, ensuring proper cable routing and alignment. Secure with screws.
Install Lever Handles: Attach the lever handles to both sides of the door. The design allows for easy adjustment for both left and right door opening directions.
Vložte baterie: Open the battery cover on the interior assembly and insert 4 AA alkaline batteries (not included).
Testovací provoz: Follow the user manual to program and test the lock's functions.

Person installing PHYSEN door lock with a screwdriver

Image: A person demonstrating the easy installation process using a screwdriver.

PHYSEN door lock suitable for left and right opening doors

Image: The lock's design accommodates both left and right door opening directions.

Návod k obsluze

The PHYSEN Smart Deadbolt offers multiple convenient ways to secure and access your property.

Odemknutí otiskem prstu

The advanced fingerprint sensor identifies your fingerprint within 0.3 seconds and unlocks the door within 1 second, boasting a 99.99% recognition rate. Up to 100 unique fingerprints can be registered.

Advanced fingerprint unlock feature of PHYSEN door lock

Image: Details on the advanced fingerprint unlock, highlighting 0.3s identification and 99.99% recognition rate.

Keypad Code Unlock

You can add up to 100 user codes for family members and create temporary codes for guests. The keypad features an anti-peeping password function, allowing you to enter random digits before or after your actual code to protect your privacy. The keypad is backlit for convenient use at night.

Anti-peeping password feature of PHYSEN keypad lock

Image: Demonstrates the anti-peeping password feature and backlit keypad for enhanced security and convenience.

Jednorázová hesla

Generate one-time passwords for single-use access, ideal for deliveries or short-term visitors.

One-time password feature for PHYSEN door lock

Image: Illustrates the use of one-time passwords for convenient access for guests or deliveries.

Funkce Auto-Lock

Configure the electronic door lock to automatically lock after 5-99 seconds. You can also use the one-touch auto-lock feature by pressing the lock key on the keypad, ensuring your door is always secured.

Smart auto-lock and one-touch lock features

Image: Highlights the smart auto-lock feature, which can be set to lock automatically after a set time, and the one-touch locking option.

Tichý režim

Activate silent mode to eliminate beeping sounds when pressing keys, providing a quiet operation experience.

Image: Depicts the silent mode feature, which mutes keypress sounds.

Mechanické odblokování klíče

For traditional access or in case of battery depletion, the lock includes two backup mechanical keys.

Údržba

Proper maintenance ensures the longevity and optimal performance of your PHYSEN door lock.

Výměna baterie

The lock operates on 4 AA batteries. A low battery indicator will alert you when it's time for replacement. Replace all batteries simultaneously with new alkaline batteries for best performance.

Image: Shows the low battery alert on the keypad, indicating when batteries need replacement.

Čištění

Otřete vnější stranu zámku měkkým hadříkemamp hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla, která by mohla poškodit povrchovou úpravu nebo elektronické součástky.

Odolnost vůči povětrnostním vlivům

The lock has an IP65 rating, making it weather-resistant and suitable for outdoor use, protecting your front door in various weather conditions.

PHYSEN door lock working in all weather conditions

Image: The lock is shown to be durable and functional in various weather conditions, including rain.

Odstraňování problémů

For detailed troubleshooting steps, please refer to the comprehensive user manual included with your product. Below are common issues and general advice:

Nesprávné pokusy o zadání kódu: If too many incorrect codes are entered, the system will lock out for 3 minutes and sound an alarm. Wait for the lockout period to expire before trying again.
Otisk prstu nebyl rozpoznán: Ujistěte se, že máte prst čistý a suchý. Pokud problém přetrvává, zkuste otisk prstu znovu zaregistrovat.
Bez napájení: Check battery installation and replace batteries if the low battery indicator is on or if the lock is unresponsive.
Mechanický klíč nefunguje: Ujistěte se, že je klíč zcela zasunutý a správně otočený. Zkontrolujte, zda v klíčové dírce nejsou nějaké překážky.

Specifikace

Funkce	Detail
Značka	FYZÉN
Název modelu	Fingerprint Door Lock (MMS-1-US-B)
Typ zámku	Biometrické
Speciální funkce	Otisk prstu
Materiál	Hliník
Barva	Černý
Typ dokončení	Matná černá
Rozměry položky D x Š x V	4.9 x 3.9 x 3.1 palce
Hmotnost položky	3.21 libry
Zdroj napájení	4 AA baterií (nejsou součástí balení)
Odolnost vůči povětrnostním vlivům	Stupeň krytí IP65

Záruka a podpora

PHYSEN is committed to providing high-quality products and customer satisfaction.

Plány ochrany

Extended protection plans are available for purchase to cover your device beyond the standard warranty:

Dvouletý ochranný plán: 6.99 $
Dvouletý ochranný plán: 8.99 $
Kompletní ochrana: 16.99 USD/měsíc (zahrnuje všechny způsobilé minulé i budoucí nákupy)

Zákaznická podpora

For further assistance, technical support, or warranty claims, please visit the official PHYSEN store or contact customer service through the platform where you purchased the product.

Navštivte PHYSEN Store on Amazon.

PHYSEN MMS-1-US-B