ISDT PC-4860S Lipo Battery Safe Parallel Charging Board

1. Konec produktuview

The ISDT PC-4860S is a safe parallel charging board designed for charging multiple 1S to 8S LiPo batteries simultaneously. It features XT60 connectors and balance ports, providing a secure and efficient solution for managing your RC battery charging needs. The board is constructed with an aluminum case for enhanced safety and heat dissipation.

Obrázek 1: Shora dolů view of the ISDT PC-4860S Safe Parallel Charging Board, showing four XT60 output ports and the main XT60 input port.

Klíčové vlastnosti:

• Safe Parallel Charging: Supports charging of 1S to 8S LiPo batteries.
• Více kanálů: Four independent output channels for parallel charging.
• Vysoká proudová kapacita: Max input current of 40A, max output current of 30A per port.
• Integrated Fuses: Equipped with 32 fuses for enhanced safety against overcurrent.
• Odolná konstrukce: Aluminum case designed to prevent explosions or fires and ensure efficient heat dissipation.
• Kompaktní design: Optimized size for portability and ease of use.

2. Obsah balení

Ověřte, zda jsou v balení přítomny všechny níže uvedené položky:

• 1 x ISDT PC-4860S Lipo Charging Plate
• 1 x XT60 Charging Cable
• 1 x 6S Lipo Battery Balance Cable

Figure 2: The ISDT PC-4860S board shown with the XT60 charging cable and the 6S balance cable.

3. Bezpečnostní informace

Read and understand all safety warnings and instructions before using this product. Failure to do so may result in fire, injury, or property damage.

• Always use this parallel charging board with a compatible LiPo battery charger.
• Ensure all batteries connected for parallel charging have the same cell count (e.g., all 3S, all 4S) and are at a similar voltage level. Charging batteries with different cell counts or significantly different voltages in parallel can be dangerous.
• Never exceed the maximum input current of 40A or the maximum output current of 30A per port.
• Do not charge damaged, swollen, or punctured batteries.
• Always charge batteries in a fire-safe area, away from flammable materials.
• Supervise the charging process at all times.
• Udržujte zařízení mimo dosah vody, vlhkosti a extrémních teplot.
• Tento výrobek není hračka. Uchovávejte mimo dosah dětí.

4. Nastavení

1. Připojení k nabíječce: Connect the main XT60 charging cable (included) from the ISDT PC-4860S board's input port to the output port of your compatible LiPo battery charger.
2. Connect Balance Cable: Connect the 6S balance cable (included) from the balance port on the ISDT PC-4860S board to the balance port on your charger. If charging batteries with a cell count less than 6S, ensure your charger's balance port is compatible or use an appropriate adapter (not included).
3. Připravte si baterie: Ensure all batteries you intend to charge in parallel have the same cell count (e.g., all 3S, all 4S) and are at a similar voltage.

5. Návod k obsluze

Follow these steps for safe parallel charging:

1. Připojte baterie: Connect up to four LiPo batteries to the XT60 output ports on the ISDT PC-4860S board. Ensure each battery's main power lead (XT60) and balance lead are correctly connected to the corresponding ports on the parallel board.
2. Set Charger Parameters: On your LiPo battery charger, set the charging parameters for the total capacity of all connected batteries. For example, if you are charging four 2200mAh 3S batteries, set your charger to charge a single 3S battery at 8800mAh (4 x 2200mAh).
3. Zahájit nabíjení: Initiate the charging process on your LiPo charger. Monitor the charging progress and battery conditions closely.
4. Odpojit baterie: Once charging is complete, first stop the charging process on your charger. Then, disconnect the batteries from the parallel board, starting with the balance leads, then the main power leads. Finally, disconnect the parallel board from the charger.

Důležité: Always connect the main power leads and balance leads of the batteries to the parallel board before starting the charger. Disconnect the batteries from the parallel board before disconnecting the parallel board from the charger.

6. Údržba

• Čištění: Use a dry, soft cloth to clean the surface of the parallel board. Do not use liquids or solvents.
• Skladování: Store the board in a cool, dry place away from direct sunlight and moisture when not in use.
• Inspekce: Periodically inspect the XT60 connectors and balance ports for any signs of wear, damage, or corrosion. Ensure all cables are in good condition.

7. Řešení problémů

8. Specifikace

Figure 3: The ISDT PC-4860S board highlighting maximum input and output current specifications.

• Model: PC-4860S
• Velikost: 88 x 58 x 16 mm (3.46" H x 2.28" Š x 0.67" V)
• Celková hmotnost: 247.5 g
• Max. Vstupní proud: 40A
• Maximální výstupní proud: 30A/Port
• Max Balance Current: 2A
• Vyvážené buňky: 1S~8S
• Typ zástrčky: XT60
• Počet portů: 4
• Bezpečnostní funkce: 32pcs Fuses, Aluminum case
• Osvědčení: CE

9. Informace o záruce

The ISDT PC-4860S Lipo Battery Safe Parallel Charging Board comes with a jednoletá záruka from the date of purchase. This warranty covers manufacturing defects and material faults under normal use. It does not cover damage caused by misuse, accident, modification, unauthorized repair, or improper installation.

For warranty claims, please retain your proof of purchase and contact ISDT customer support.

10. Podpora

For further assistance, technical support, or inquiries regarding the ISDT PC-4860S, please visit the official ISDT store or contact their customer service department.

ISDT Official Store: https://www.amazon.com/stores/ISDTOfficial/page/CD66BDD7-E050-477A-B081-1CA75B65F070