MicroZone MC6C Mini V2 2.4G 6-Channel RC Controller and Receiver System User Manual

1. Úvod

This manual provides detailed instructions for the proper setup, operation, and maintenance of your MicroZone MC6C Mini V2 2.4G 6-Channel RC Controller and Receiver System. This system is designed for controlling various remote-controlled models, including aircraft, drones, multirotors, helicopters, and boats. Please read this manual thoroughly before using the product to ensure safe and efficient operation.

2. Bezpečnostní informace

Always prioritize safety when operating RC equipment. Failure to follow these guidelines may result in injury or damage to property.

• Provozní prostředí: Operate your RC model in open areas, away from people, animals, buildings, and power lines. Avoid operating in strong winds or adverse weather conditions.
• Bezpečnost baterie: Use only recommended batteries. Ensure correct polarity during installation. Do not short-circuit, disassemble, or expose batteries to extreme temperatures. Dispose of batteries responsibly.
• Předletové kontroly: Before each use, verify that all controls are functioning correctly, batteries are charged, and the receiver is properly bound to the transmitter.
• Děti: This product is not a toy. Adult supervision is required for users under 14 years of age.
• Rušení: The 2.4G system is designed to minimize interference, but always be aware of potential sources of radio interference.

3. Konec produktuview

The MicroZone MC6C Mini V2 controller features a compact design with essential controls for 6-channel operation. Below is a diagram illustrating the main components and their functions.

Obrázek 3.1: Front panel and control layout of the MicroZone MC6C Mini V2 controller.

This image displays the front of the MicroZone MC6C Mini V2 controller with labels pointing to various controls. Key components include the built-in antenna, power light, mode light, D/R switch, mode switch, Channel 5 and Channel 6 switches, two rockersticks (left for throttle/elevator trim, right for aileron/rudder trim), and the power switch. The lower section shows indicators for V Tail Mixed Control, Delta Wing Mixed Control, Channel Reverse, Lock, and a Hybrid Control Function Switch (MIX).

3.1 Součásti řídicí jednotky

• Vestavěná anténa: Transmits the 2.4G signal to the receiver.
• Kontrolka napájení: Indicates the power status of the transmitter.
• Režim světla: Označuje aktuální provozní režim.
• Přepínač D/R: Dual Rate switch, adjusts the sensitivity of control surfaces.
• Přepínač režimu: Selects between different flight modes or functions.
• Přepínače kanálů 5 a 6: Auxiliary switches for additional functions on your model.
• Rockerové tyče: Control primary flight functions (Throttle, Aileron, Elevator, Rudder).
• Trims (Throttle, Elevator, Rudder, Aileron): Fine-tune the neutral position of control surfaces.
• Vypínač: Zapíná/vypíná vysílač.
• Channel Reverse Indicators: Show which channels have reverse enabled.
• Lock Indicator/Switch: For specific locking functions, refer to your model's manual.
• MIX Switch: Hybrid control function switch for advanced mixing.
• V Tail Mixed Control Indicator: Indicates V-tail mixing is active.
• Smíšený kontrolní indikátor Delta Wing: Indicates delta wing mixing is active.

Obrázek 3.2: Back panel of the MicroZone MC6C Mini V2 controller, showing the battery compartment.

Tento obrázek ukazuje zadní část view of the MicroZone MC6C Mini V2 controller. A large rectangular cover in the center indicates the battery compartment. There are also ventilation holes on either side and mounting points for a carrying handle at the top.

4. Nastavení

4.1 Instalace baterie

1. Vyhledejte přihrádku na baterie na zadní straně vysílače (viz obrázek 3.2).
2. Slide the battery compartment cover downwards or unclip it to open.
3. Insert the required batteries (typically AA batteries, check product specifications for exact type and quantity) ensuring correct polarity (+/-).
4. Bezpečně zavřete kryt bateriového prostoru.

4.2 Párování přijímače

Binding is the process of electronically linking the transmitter to its receiver. This procedure ensures that your receiver only responds to signals from your specific transmitter.

1. Ujistěte se, že je vysílač VYPNUTÝ.
2. Connect the receiver to its power source (e.g., flight controller, ESC with BEC).
3. Locate the bind button or bind port on the receiver. Insert a bind plug if required.
4. Power on the receiver. The receiver's LED should flash rapidly, indicating it's in bind mode.
5. While holding down the bind button on the transmitter (if applicable, refer to specific transmitter instructions), turn on the transmitter.
6. The transmitter and receiver LEDs should change to a solid light, indicating a successful bind.
7. Turn off both the transmitter and receiver, then power them on again in the correct sequence (transmitter first, then receiver) to confirm the bind.

Note: Specific binding procedures may vary slightly. Always refer to the receiver's manual for precise instructions.

4.3 Počáteční kontroly

• Verify that all control surfaces (ailerons, elevator, rudder) move in the correct direction relative to stick inputs. Adjust channel reverse settings on the transmitter if necessary.
• Check the range of motion for all servos.
• Ensure all switches (D/R, Channel 5/6, Mode) function as expected.

5. Návod k obsluze

5.1 Basic Controls (Mode 2 - Left Hand Throttle)

• Levá páčka (plyn/kormidlo):
  • Nahoru/dolů: Controls throttle (power).
  • Vlevo/vpravo: Controls rudder (yaw).
• Pravá páčka (křidélka/výškovka):
  • Nahoru/dolů: Controls elevator (pitch).
  • Vlevo/vpravo: Controls ailerons (roll).

Note: If your transmitter is configured for Mode 1 (Right Hand Throttle), the functions of the left and right sticks for throttle and elevator will be swapped.

5.2 Úpravy trimu

Trims are used to make minor adjustments to the neutral position of your control surfaces, ensuring the model flies straight without constant stick input.

• Škrtící klapka: Adjusts the idle speed of the motor.
• Elevator Trim: Adjusts the nose-up/nose-down attitude.
• Trim kormidla: Adjusts left/right yaw.
• Trim křidélek: Adjusts left/right roll.

Adjust trims incrementally during flight until the model maintains a stable attitude.

5.3 D/R (Dual Rate) Switch

The D/R switch allows you to select between two different control sensitivities for specific channels (e.g., aileron, elevator, rudder). This is useful for switching between precise control for gentle flying and more aggressive control for aerobatics.

5.4 Channel 5 & 6 Switches

These switches provide additional channels for controlling auxiliary functions on your model, such as landing gear, flaps, lights, or camera triggers. The specific function depends on how your model's receiver and flight controller are configured.

5.5 Zpětný chod kanálu

If a control surface moves in the opposite direction to your stick input, you can reverse that channel's output using the channel reverse function on the transmitter. Refer to the diagram (Figure 3.1) for the Channel Reverse indicators and controls.

6. Údržba

• Čištění: Wipe the transmitter with a soft, dry cloth. Do not use solvents or abrasive cleaners.
• Skladování: Store the transmitter in a cool, dry place, away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods to prevent leakage.
• Péče o baterie: Always use fresh batteries or fully charged rechargeable batteries. Do not mix old and new batteries or different types of batteries.
• Inspekce: Periodically check for any loose connections, damaged wires, or physical damage to the casing or sticks.

7. Řešení problémů

8. Specifikace

• Model: MC6C Mini V2
• kanály: 6 kanály
• Frekvence: 2.4 GHz
• Výrobce: XINLINCHENG
• Značka: HUTIANSN (as listed in specifications, though MicroZone is product line)
• Požadovaná montáž: Ano
• Rozměry balení: 3 x 2 x 1 cm
• Hmotnost položky: 50 g
• Země původu: Čína

9. Záruka a podpora

Informace o záruce a technickou podporu naleznete v dokumentaci dodané s vaším nákupem nebo se obraťte přímo na prodejce/výrobce. Uschovejte si doklad o koupi pro případné reklamace.

Manufacturer: XINLINCHENG

Pro další pomoc navštivte prosím oficiální stránky website of the manufacturer or contact their customer service department.