ECD Germany IP-2150

ECD Germany 2.5T Hydraulic Car Jack (Model IP-2150) Instruction Manual

Brand: ECD Germany | Model: IP-2150

Zavedení

This manual provides essential instructions for the safe and effective use, maintenance, and troubleshooting of your ECD Germany 2.5T Hydraulic Car Jack. Please read this manual thoroughly before operation to ensure proper handling and to prevent personal injury or damage to property.

Důležité bezpečnostní pokyny

VAROVÁNÍ: Failure to follow these instructions may result in serious injury or death. Always prioritize safety when operating lifting equipment.

  • Read Entire Manual: Understand all instructions and warnings before using this jack.
  • Jmenovitá kapacita: Do not exceed the jack's rated capacity of 2.5 tons (2500 kg).
  • Stabilní povrch: Always use the jack on a hard, level, and stable surface. Avoid soft ground or inclines.
  • Stabilita vozidla: Ensure the vehicle is in park (P), the ignition is off, and the parking brake is engaged. Block wheels that are not being lifted.
  • Proper Lift Points: Only lift the vehicle at manufacturer-recommended lift points. Use the provided rubber pads to protect the vehicle's chassis.
  • Podpěrné stojany: After lifting, immediately support the vehicle with appropriate jack stands. Never work under a vehicle supported only by a hydraulic jack.
  • Vyčistit oblast: Keep hands, feet, and other body parts clear of moving parts and the area under the vehicle.
  • Lowering Slowly: Lower the vehicle slowly and carefully.
  • Inspekce: Inspect the jack for damage or leaks before each use. Do not use if damaged.
  • Děti a přihlížející: Udržujte děti a neoprávněné osoby mimo pracovní oblast.

Obsah balení

Po vybalení ověřte, zda jsou všechny součásti přítomny a nepoškozené:

  • 1 x ECD Germany 2.5T Hydraulic Car Jack
  • 2 x Rubber Pads (for scratch and slip protection)
  • 1 x SUV Adapter (for increased lift height)
  • 1 x Pump Lever (operating handle)
ECD Germany 2.5T Hydraulic Car Jack with included accessories: two rubber pads and one SUV adapter.

Image: The hydraulic jack shown with its pump lever, two rubber pads, and an SUV adapter, as included in the package.

Specifikace

Číslo modeluIP-2150
Kapacita2500 kg (2.5 Tons)
Minimální výška zdvihu80 mm
Maximální výška zdvihu360 mm
Rozměry produktu (D x Š x V)53 x 17 x 13 cm
Hmotnost produktu10.8 kg
MateriálAlloy Steel, Cast Iron
StylHydraulické
Kola2 fixed, 2 x 360° swivel casters
Technical diagram of the hydraulic car jack showing dimensions: minimum 80mm, maximum 360mm lift height, and overall length.

Image: Detailed dimensions of the hydraulic jack, illustrating its minimum and maximum lift heights, and overall length.

Nastavení a příprava

  1. Rozbalit: Carefully remove the jack and all accessories from the packaging.
  2. Kontrolovat: Check the jack for any signs of damage or oil leaks that may have occurred during shipping. Do not use if damaged.
  3. Sestavte rukojeť: Insert the pump lever into the handle socket. Ensure it is securely seated.
  4. Bleed Air (First Use): Before first use, it is recommended to bleed any air from the hydraulic system.
    • Otočte vypouštěcí ventil proti směru hodinových ručiček, abyste jej zcela otevřeli.
    • Pump the handle several times to expel any trapped air.
    • Otočením vypouštěcího ventilu ve směru hodinových ručiček jej zavřete.
  5. Připojit příslušenství: Place a rubber pad on the saddle of the jack. If lifting an SUV or a vehicle requiring extra height, attach the SUV adapter on top of the rubber pad.
Detailní záběr view of the jack's saddle with a rubber pad and SUV adapter being attached.

Image: Illustration of attaching the rubber pad and SUV adapter to the jack's saddle for proper vehicle contact and protection.

Návod k obsluze

Zvedání vozidla:

  1. Připravte vozidlo: Park the vehicle on a firm, level surface. Engage the parking brake and place the transmission in "Park" (automatic) or a low gear (manual). Block the wheels that will remain on the ground.
  2. Pozice Jacka: Locate the vehicle manufacturer's recommended lifting points. Position the jack directly under the designated lift point, ensuring the saddle with the rubber pad (and SUV adapter if needed) is centered and making full contact.
  3. Zavřete vypouštěcí ventil: Turn the pump lever clockwise until the release valve is fully closed. This prepares the jack for lifting.
  4. Zvedací vozidlo: Pump the handle up and down to raise the vehicle to the desired height. Lift only high enough to perform the necessary work.
  5. Zajištění pomocí zvedáků: Immediately place appropriately rated jack stands under the vehicle's designated support points. Lower the vehicle slowly until it rests securely on the jack stands. Never rely solely on the hydraulic jack for support.
  6. Odstraňte Jacka: Once the vehicle is safely supported by jack stands, you can remove the hydraulic jack.
Hydraulic car jack positioned under a vehicle's lift point, ready to lift.

Image: The hydraulic jack correctly placed under a vehicle's designated lifting point, demonstrating proper positioning before lifting.

Spouštění vozidla:

  1. Mírně zvedněte: If the vehicle is on jack stands, pump the jack handle a few times to slightly raise the vehicle off the jack stands.
  2. Demontáž podpěr: Opatrně vyjměte zvedáky zpod vozidla.
  3. Spodní část vozidla: Slowly turn the pump lever counter-clockwise to open the release valve. The vehicle will begin to lower. Control the lowering speed by adjusting how much you open the valve.
  4. Úplně dolů: Once the vehicle is fully lowered and resting on the ground, remove the jack from underneath.
Diagram illustrating the jack's simple lift system, showing the pump lever insertion and the process to open the drain valve for lowering.

Image: A visual guide to the jack's lifting and lowering mechanism, including how to insert the lever and open the drain valve for controlled descent.

Údržba

  • Mazání: Periodically lubricate all moving parts with light machine oil.
  • Hydraulický olej: Check the hydraulic oil level regularly. If low, refill with high-quality hydraulic jack oil. Do not use brake fluid or other fluids.
  • Čištění: Udržujte zvedák čistý a bez nečistot, mastnoty a úlomků.
  • Skladování: Store the jack in a dry, clean place with the ram fully retracted to prevent corrosion and seal damage.
  • Inspekce: Regularly inspect for wear, damage, or leaks. Any damaged parts must be replaced by qualified personnel.

Odstraňování problémů

ProblémMožná příčinaŘešení
Zvedák nezvedá nebo zvedá pomalu.
  • Uvolňovací ventil není zcela uzavřen.
  • Nízká hladina hydraulického oleje.
  • Vzduch v hydraulickém systému.
  • Přetížení.
  • Turn pump lever clockwise to fully close valve.
  • Zkontrolujte a doplňte hydraulický olej.
  • Bleed air from the system (see Setup section).
  • Ensure load does not exceed 2.5T capacity.
Zvedák se pod zátěží spustí dolů.
  • Uvolňovací ventil není zcela uzavřen.
  • Internal seal leakage.
  • Přetížení.
  • Turn pump lever clockwise to fully close valve.
  • Pro servis kontaktujte zákaznickou podporu.
  • Ensure load does not exceed 2.5T capacity.
Jack does not lower.
  • Release valve stuck or obstructed.
  • Gently try to turn the pump lever counter-clockwise. Do not force. If still stuck, contact customer support.

Informace o záruce

The manufacturer provides a warranty for this product. Please refer to the warranty card included with your purchase or visit the official ECD Germany webPodrobné záruční podmínky naleznete na webových stránkách. Uschovejte si doklad o koupi pro případ reklamace.

The product specifications indicate that a manufacturer's warranty is provided.

Zákaznická podpora

For technical assistance, spare parts, or warranty inquiries, please contact ECD Germany customer service. You can find contact information on the official ECD Germany webwebu nebo prostřednictvím svého prodejce.

Online zdroje: Visit the ECD Germany Store on Amazon

© 2026 ECD Germany. All rights reserved.

Tato příručka se může změnit bez předchozího upozornění.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.