Zavedení
Welcome to your new DEKO Auto Darkening Welding Helmet MZ350T. This manual provides essential information for safe and effective use, setup, operation, and maintenance of your welding helmet. Please read this manual thoroughly before using the product and keep it for future reference.
Bezpečnostní informace
Obecná bezpečnostní opatření
- Při svařování vždy používejte vhodné osobní ochranné prostředky (OOP).
- Ensure the helmet is correctly adjusted and functioning before each use.
- Do not use the helmet if any part is damaged.
- Protect the lens from scratches and impacts.
- Zabraňte přímému vystavení svařovacímu oblouku bez řádné ochrany očí.
- Udržujte děti a nepovolané osoby mimo dosah svařovacího prostoru.
Ochrana očí
- This helmet provides protection against harmful UV/IR radiation even in the light state.
- The auto-darkening filter is designed to protect your eyes from intense light during welding.
- Never look directly at a welding arc with an unprotected eye.
Elektrická bezpečnost
- Ensure all welding equipment is properly grounded.
- Neprovozujte ve vlhkých podmínkách.
Vlastnosti produktu
- Automaticky ztmavující filtr: Automatically switches from light to dark in 1/15000 seconds upon arc strike.
- Technologie True Color: Poskytuje realistický view of the work area, enhancing clarity and detail.
- Solar Powered with Replaceable Battery: Utilizes solar energy for primary power and a CR2032 lithium battery for backup.
- Nastavitelná citlivost a zpoždění: Allows customization for different welding processes and environments.
- Variabilní ovládání stínění: External knob for adjusting dark shade from DIN 9-13.
- Pohodlná pokrývka hlavy: Upgraded adjustable headgear with soft sponge for extended wear.
- Víceúčelová aplikace: Suitable for MMA, MIG, TIG welding, and Plasma Grinding.
Komponenty skončilyview
Struktura přilby
The DEKO Auto Darkening Welding Helmet consists of the helmet shell, auto-darkening filter (ADF), and adjustable headgear.
Auto-Darkening Filter (ADF)
The ADF unit contains the lens display, sensitivity control, delay control, and a replaceable CR2032 lithium battery.
Nastavení
Nastavení pokrývky hlavy
The headgear is designed for comfort and stability. Adjust the top strap and angle knob to fit your head securely. Use the fixed knob to adjust tightness for a snug fit.
Battery Installation/Check
The helmet comes with a pre-installed CR2032 battery. Ensure it is properly seated. The solar panel charges the internal system, extending battery life. A low battery indicator will signal when replacement is needed.
Návod k obsluze
Zapnutí/vypnutí
The helmet is always ready for use due to its solar power and automatic activation. There is no manual on/off switch. It will automatically activate when exposed to light and darken upon arc strike.
Nastavení odstínu
Use the external dark shade knob to select the appropriate shade level (DIN 9-13) for your welding application. Refer to welding standards for recommended shade levels based on amperage a materiál.
Ovládání citlivosti
Adjust the internal sensitivity knob to control how easily the filter reacts to the welding arc. Higher sensitivity is suitable for low ampvysoce výkonné TIG svařování, zatímco nižší citlivost pomáhá předcházet falešnému spuštění z okolního světla.
Kontrola zpoždění
Adjust the internal delay knob to set the time the filter remains dark after the welding arc stops. A longer delay is recommended for high amperage welding to protect against afterglow and eye fatigue.
Režim broušení
When performing grinding operations, ensure the helmet is set to grinding mode (light state) to prevent the filter from darkening. This is typically achieved by rotating the external knob to the 'Grind' position or by setting the shade to the lightest possible setting (DIN 4).
Údržba
Čištění helmy
- Clean the helmet shell with mild soap and water. Avoid harsh abrasives or solvents that could damage the material.
- Clean the outer and inner protective lenses with a soft, clean cloth. Do not use abrasive cleaners or rough materials that could scratch the lenses.
Výměna baterie
The helmet uses a replaceable CR2032 lithium battery. If the low battery indicator appears or the filter fails to darken consistently, replace the battery. To replace, locate the battery compartment on the ADF unit, open it, and insert a new CR2032 battery with the correct polarity (+ side up).
Skladování
Store the helmet in a dry, clean place away from direct sunlight and extreme temperatures. Prolonged exposure to heat or cold can affect the performance and lifespan of the auto-darkening filter.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Filter does not darken | Slabá baterie | Vyměňte baterii CR2032. |
| Filter does not darken | Arc sensors obstructed | Clean or clear sensors. |
| Filter does not darken | Příliš nízká citlivost | Zvyšte nastavení citlivosti. |
| Filter flickers | Příliš vysoká citlivost | Snižte nastavení citlivosti. |
| Filter flickers | Rušení okolního světla | Adjust sensitivity or work in a less brightly lit area. |
| Špatná viditelnost | Protective lenses dirty/scratched | Vyčistěte nebo vyměňte ochranné čočky. |
Specifikace
| Funkce | Detail |
|---|---|
| Číslo modelu | MZ350T |
| Model objektivu | DX-350D |
| View Plocha | 90 x 35mm (3.54" x 1.38") |
| Velikost rámečku filtru | 110 x 90mm (4.33" x 3.54") |
| Obloukové senzory | 2 |
| Přepnout čas | Light to dark in 1/15000s |
| Úprava zpoždění | 0.1-1.0s |
| Ovládání citlivosti | Nízká-Vysoká |
| Rozsah odstínů | Light DIN4, Dark Variable 9-13 |
| Automatické ztmavení | Ano |
| True Color | Ano |
| Napájení | Lithium Battery + Solar Cells |
| Typ baterie | Vyměnitelný CR2032 |
| Materiál helmy | PP |
| Svařovací procesy | MMA, MIG, MAG/CO2, TIG |
| UV/IR ochrana | DIN 16 |
| Optická třída | 1/1/1/2 |
| Hmotnost položky | 710 g |
| Rozměry produktu | 5.08 x 5.08 x 5.08 cm |
Záruka a podpora
For warranty information and technical support, please refer to the contact details provided with your purchase or visit the official DEKO webmísto. Uschovejte si doklad o koupi pro případ záručních reklamací.