NEJE Automatic Air Assist Set (48L/min) Instruction Manual

Zavedení

This manual provides detailed instructions for the installation, operation, and maintenance of your NEJE Automatic Air Assist Set. This device is designed to enhance the performance of NEJE laser engraving machines by providing a steady airflow of 48 liters per minute, which helps protect the laser lens and improve engraving quality.

Bezpečnostní informace

Please read and understand all safety instructions before operating the air assist set. Failure to follow these instructions may result in injury or damage to the equipment.

• Ensure the power supply is disconnected from the laser engraver before installation or maintenance.
• Operate the air assist set in a well-ventilated area.
• Keep the air pump away from water or damp prostředí.
• Do not block the air intake or outlet of the pump during operation.
• Používejte pouze dodaný napájecí adaptér a příslušenství.
• Uchovávejte mimo dosah dětí.

Obsah balení

Ověřte, zda jsou v balení obsaženy všechny níže uvedené položky:

Image: Contents of the NEJE Automatic Air Assist Set package, including the air pump, relay module, 12V 2A power adapter, and transparent air tube.

• Vzduchové čerpadlo x 1
• Relay Module x 1
• 12V 2A Power Adapter x 1
• Transparent Air Tube x 1

Specifikace

Nastavení a instalace

Follow these steps to correctly install the NEJE Automatic Air Assist Set with your NEJE laser engraving machine.

Obrázek: Podrobný view of connecting the air assist relay module to the M7/M8 port on the NEJE laser engraver's motherboard.

1. Vypnout: Ensure your NEJE laser engraving machine is completely powered off and unplugged from the power source.
2. Locate M7/M8 Port: Identify the M7 or M8 port on the motherboard of your NEJE laser engraving machine. These ports are typically labeled.
3. Connect Relay Module: Connect the included relay module to the M7/M8 port. The relay module enables automatic control of the air pump.
4. Připojení vzduchového čerpadla: Connect the air pump to the relay module.
5. Připojení vzduchové trubice: Securely attach one end of the transparent air tube to the air pump's outlet and the other end to the air nozzle on your laser module. Ensure a snug fit to prevent air leakage.
6. Připojte napájecí adaptér: Plug the 12V 2A power adapter into the air pump and then into a suitable power outlet.
7. Zapnutí: Reconnect power to your NEJE laser engraving machine. The air assist set will now be ready for automatic operation, adapting to software like Lightburn, LaserGRBL, and NEJE software.

Návod k obsluze

The NEJE Automatic Air Assist Set is designed to operate in conjunction with your NEJE laser engraver, providing controlled airflow during engraving and cutting processes. When properly connected to the M7/M8 port, the air assist will activate automatically with your laser operations.

Benefits of Air Assist

Strong and Stable Airflow (48L/min)

Image: Illustration demonstrating the consistent and powerful 48 liters per minute airflow from the air assist nozzle onto the material during laser operation.

The air pump delivers a robust and consistent airflow of 48 liters per minute directly to the laser's focal point. This steady stream of air is crucial for effective material processing and maintaining optimal laser performance.

Cleaner Material Surface

Image: Side-by-side comparison of a flower-shaped wooden cutout. The top image, labeled "With Air Assist," shows a clean, unblemished surface. The bottom image, labeled "No Air Assist," shows burn marks and discoloration around the engraved lines.

By rapidly reducing the surface temperature of the material, the air assist prevents deformation and discoloration caused by high-temperature laser work. This results in smoother lines, intact patterns, and a cleaner material surface, contributing to a higher quality finished product.

Protection for Laser Module Lens

Image: A split diagram showing a laser module. On the left, labeled "With Air Assist," air blows smoke and debris away from the lens. On the right, labeled "No Air Assist," smoke and debris accumulate on the lens, shown as a dirty lens below.

The steady airflow effectively blows away smoke, dust, and debris generated during laser engraving and cutting. This prevents these particles from rising and contaminating the laser module lens, thereby extending the service life and maintaining the clarity of your laser module.

Low Noise and Vibration Operation

Image: A person comfortably reading in a chair, with the NEJE air assist pump visible in the foreground, illustrating its low noise and vibration characteristics during operation.

The NEJE air assist pump is engineered for quiet operation with minimal vibration, ensuring a more pleasant working environment without significant noise disturbance.

Údržba

Regular maintenance ensures the longevity and optimal performance of your air assist set.

• Čistý vzduchový filtr: Periodically check and clean the air filter (if applicable) to prevent dust accumulation and maintain efficient airflow.
• Inspect Air Tube: Ensure the transparent air tube is free from kinks, blockages, or damage. Replace if necessary.
• Udržujte průduchy volné: Ensure the air pump's ventilation openings are clear of obstructions to prevent overheating.
• Správně skladujte: When not in use for extended periods, store the air assist set in a clean, dry environment.

Odstraňování problémů

Běžné problémy a jejich řešení naleznete v tabulce níže.

Záruka a podpora

NEJE is committed to providing high-quality products and customer satisfaction. If you encounter any issues or have questions regarding your NEJE Automatic Air Assist Set, please refer to the following:

• Technická podpora: For professional technical assistance, please visit the official NEJE support webmísto.
• Informace o záruce: Details regarding product warranty can be found on the NEJE official webwebu nebo kontaktováním zákaznického servisu.

Více informací a podpůrných zdrojů naleznete na adrese NEJE Official Store on Amazon or their dedicated support channels.