1. Úvod
Thank you for choosing the MakerHawk LCD Handheld Digital Oscilloscope Kit. This device integrates a 2-channel digital oscilloscope, a true RMS multimeter, and a DDS function signal generator into a compact, portable unit. Designed for electronics enthusiasts, engineers, and technicians, it offers a 120MHz bandwidth and 250MSa/s real-time sampling rate for precise measurements. This manual provides essential information for safe and effective operation, setup, maintenance, and troubleshooting.
2. Bezpečnostní informace
Please read and understand all safety instructions before using the device. Failure to follow these instructions may result in electric shock, fire, or damage to the device.
- Neprovozujte zařízení ve vlhku nebo damp podmínky.
- Ensure proper grounding when connecting to external circuits.
- Nepřekračujte maximální vstupní objemtage ratings specified in the technical specifications.
- Use only the probes and accessories provided or approved by MakerHawk.
- Avoid touching exposed connections or components while the device is powered on.
- Nepokoušejte se zařízení otevírat ani upravovat. Veškerý servis svěřte kvalifikovanému personálu.
- Při měření vysokých objtage or non-isolated circuits, do not use the multimeter while charging (powered by the built-in battery).
3. Obsah balení
Ověřte, zda jsou všechny níže uvedené položky součástí balení. Pokud některé položky chybí nebo jsou poškozené, kontaktujte zákaznickou podporu.
- 1x MakerHawk Digital Oscilloscope (DSO3D12)
- 2x Oscilloscope Probes (1X/10X)
- 2x Multimeter Probes (Red, Black)
- 2x Gray Probe Hooks (including ground alligator clamp)
- 1x Compensating Adjusting Rod
- 2x Insulation Protective Caps
- 8x Identification Rings
- 1x nabíjecí kabel USB Type-C
- 1x Uživatelská příručka
Figure 3.1: Contents of the MakerHawk Digital Oscilloscope Kit.
4. Konec produktuview
The MakerHawk DSO3D12 is a versatile 3-in-1 device combining the functionalities of a digital oscilloscope, a multimeter, and a signal generator. Its compact design and robust features make it suitable for various electronic testing and diagnostic tasks.
Figure 4.1: The 3-in-1 functionality of the MakerHawk Digital Oscilloscope.
Klíčové vlastnosti:
- Profesionální design: 2-channel input oscilloscope with up to 120MHz bandwidth and 250MSa/s real-time sampsazba lingu.
- Integrovaný generátor signálu: Built-in DDS function signal generator capable of outputting sine, square, and triangle waves with adjustable frequency (0-2MHz) and amplitude (2.5V).
- High-Precision Multimeter: Features a true RMS multimeter with fast software calibration, allowing simultaneous use with the oscilloscope for low voltage/resistance/continuity measurements.
- Přenosný a odolný: Compact design with a 3.2-inch LCD backlight display. Includes a built-in 2500mAh lithium battery for up to 4-6 hours of continuous use and a high-voltage protection module (up to 400V).
- Flexible Trigger Modes: Supports Auto, Normal, and Single trigger modes, with settings for time base, amplitude, and trigger slope. One-touch AUTO function for automatic screen adaptation.
Figure 4.2: Device features including battery, display, and safety.
5. Nastavení
5.1 Nabíjení zařízení
The device is equipped with a built-in 2500mAh lithium battery. Before first use, fully charge the device using the provided USB Type-C cable and a standard 5V USB power adapter.
- Connect the USB Type-C cable to the device's charging port and the other end to a 5V USB power source.
- The charging indicator light will be red while charging.
- Charging is complete when the indicator light turns green. A full charge typically takes over 4 hours at a charging current of approximately 700mA (3.5W).
- Avoid using the multimeter functions while the device is charging, especially when measuring high-voltage nebo neizolované obvody.
5.2 Připojení sond
Properly connecting the probes is crucial for accurate measurements.
- Osciloskopické sondy: Connect the BNC connectors of the oscilloscope probes to the CH1 and CH2 inputs on the top of the device. Ensure a secure connection by twisting the connector clockwise.
- Multimetrové sondy: Insert the red multimeter probe into the 'VΩ' jack and the black probe into the 'COM' jack for voltage and resistance measurements. For current measurements, use the '10A' or '600mA' jacks as appropriate.
- Kompenzace sondy: For oscilloscope probes, it is recommended to perform probe compensation to ensure accurate waveform display. Connect the probe to a known square wave source (e.g., the device's built-in signal generator or a dedicated probe compensation output) and adjust the trimmer on the probe until the square wave appears flat-topped without overshoot or undershoot.
6. Návod k obsluze
6.1 Obecné rozhraní
The device features a 3.2-inch LCD display and a combination of soft silicone keys for navigation and function selection. The main screen displays waveform data, measurement parameters, and menu options.
6.2 Režim osciloskopu
To enter Oscilloscope mode, ensure the device is powered on. The default display typically shows the waveform. Use the navigation buttons to adjust settings.
Základní měření
- Vertical Scale (mV/div): Upravuje objemtage sensitivity. Use the 'CH1' and 'CH2' buttons to select the channel and then the 'mV' or 'V' buttons to change the scale.
- Horizontal Scale (Time Base): Adjusts the time per division. Use the 'Time base' button and navigation keys to change the sweep speed.
- Pozice: Adjusts the vertical or horizontal position of the waveform on the screen.
- Tlačítko AUTO: Pressing the 'AUTO' button automatically adjusts the vertical and horizontal scales and trigger settings to display a stable waveform.
- Funkce měření: The device supports 14 types of automatic measurement functions, including Frequency, Peak-to-Peak Voltage (PKPK), Mean Voltage (Mean), RMS, Max, Min, Period, Duty Cycle, etc. These are typically displayed on the screen or accessible via a 'Meas' menu.
Režimy spouštění
The device offers three trigger modes to stabilize repetitive waveforms and capture single-shot events.
- Auto Trigger: The oscilloscope triggers automatically even without a stable signal, ensuring a waveform is always displayed.
- Normal Trigger: The oscilloscope triggers only when the input signal meets the specified trigger conditions (level, slope). If no trigger condition is met, the display remains unchanged.
- Single Trigger: The oscilloscope waits for a single trigger event, captures the waveform, and then stops. This is useful for capturing non-repetitive or transient events.
- Trigger Level and Slope: Adjust the trigger level to specify the voltage point at which the trigger occurs. Select the trigger slope (rising edge or falling edge) to define the direction of the voltage change that initiates the trigger.
Režim XY
XY mode displays the voltage of channel 1 (CH1) on the horizontal axis and the voltage of channel 2 (CH2) on the vertical axis. This mode is useful for observing phase relationships between two signals, often resulting in Lissajous figures.
FFT spektrum
The Fast Fourier Transform (FFT) function converts time-domain waveforms into the frequency domain, allowing analysis of the frequency components within a signal. This is useful for identifying harmonics, noise, and signal integrity issues.
Referenční průběh
This feature allows you to save a waveform and display it as a reference against a live waveform. This is useful for comparing current measurements with a known good signal or for analyzing changes over time.
Figure 6.1: Advanced Oscilloscope Functions.
6.3 Režim multimetru
The built-in true RMS multimeter supports various measurements. When in oscilloscope mode, a small multimeter window can be displayed in the upper right corner. For full-screen multimeter operation, select the dedicated multimeter mode.
Figure 6.2: High-precision Multimeter Function.
- svtage Měření: Connect probes to 'VΩ' and 'COM' for DC or AC voltage.
- Měření odporu: Connect probes to 'VΩ' and 'COM' for resistance.
- Test kontinuity: Connect probes to 'VΩ' and 'COM' for continuity.
- Aktuální měření: Connect the red probe to '10A' or '600mA' and the black probe to 'COM' for current measurements. Ensure the correct jack is used to avoid damaging the device.
6.4 Režim generátoru signálu
The integrated DDS function signal generator can output various waveforms for testing and calibration purposes.
Figure 6.3: Multiple Waveforms and Signal Generator Interface.
- Typy průběhů: Select between sine wave, square wave, and triangle wave outputs.
- Nastavení frekvence: Adjust the output frequency from 0 to 2MHz.
- Amplituda: Voltage amplitude is fixed at 2.5V.
- Pracovní cyklus: For square waves, the duty cycle is adjustable from 1% to 99%.
7. Údržba
- Čištění: K čištění zařízení používejte měkký, suchý hadřík. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla.
- Skladování: Přístroj skladujte na chladném a suchém místě mimo dosah přímého slunečního záření a extrémních teplot.
- Péče o baterie: Chcete-li prodloužit životnost baterie, vyvarujte se častého úplného vybíjení. Pokud baterii skladujete delší dobu, nabijte ji přibližně na 50 % a dobíjejte ji každé několik měsíců.
- Péče o sondu: Inspect probes regularly for damage. Replace worn or damaged probes immediately to ensure safety and accuracy.
8. Řešení problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Zařízení se nezapne | Low battery; Power button not pressed correctly; Device fault | Charge the device fully; Press and hold the power button; Contact customer support if issue persists. |
| Nezobrazuje se žádný průběh | Probe not connected; Incorrect input settings; Trigger not set correctly; Signal too small or too large | Ensure probes are securely connected; Press 'AUTO' button; Adjust vertical scale (mV/div) and horizontal scale (Time Base); Check trigger mode and level. |
| Nestabilní průběh | Incorrect trigger settings; Noisy signal | Adjust trigger level and slope; Change trigger mode to 'Normal' or 'Single'; Check for external noise sources. |
| Nepřesná měření | Uncompensated probe; Incorrect probe attenuation setting; Device not calibrated | Perform probe compensation; Ensure probe attenuation (1X/10X) matches the device setting; Contact customer support for calibration if suspected. |
| Multimeter readings are incorrect | Incorrect probe connection; Wrong measurement range selected; Device fault | Ensure probes are in the correct jacks ('VΩ', 'COM', '10A', '600mA'); Select the appropriate measurement function (voltage, resistance, current); Contact customer support. |
9. Technické specifikace
The following table outlines the key technical specifications of the MakerHawk DSO3D12.
Obrázek 9.1: Podrobné technické parametry.
| Parametr | Hodnota |
|---|---|
| Rozměry produktu | 5.71 x 3.39 x 1.26 palce; 1.3 libry |
| Baterie | 1 A batteries required (included) - 2500mAh Lithium |
| Zdroj napájení | Battery Powered (USB Type-C 5V Charging) |
| Kanály | 2 |
| Šířka pásma | 120MHz (CH1 Only), 60MHz (CH1+CH2) |
| S. v reálném časeampsazba ling | 250MSa / s |
| Ekvivalent Sampsazba ling | 500MSa / s |
| Velikost obrazovky | 3.2palcový TFT LCD |
| Minimální rozsah | 10 mV/div |
| Max. Vstupní objemtage | 400V (Peak) |
| Výstup generátoru signálu | Sine, Square, Triangle (0-2MHz, 2.5V Amplituda) |
| Typ multimetru | Skutečné RMS |
| Režimy spouštění | Auto, Normal, Single |
| Barva | Black, White, or Gray |
10. Záruka a podpora
MakerHawk products are designed for reliability and performance. This device comes with a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty details, please refer to the warranty card included with your product or visit the official MakerHawk webmísto.
For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact MakerHawk customer service through the contact information provided on our website or your purchase platform. Please have your product model number (DSO3D12) and purchase date ready when contacting support.