Einaus 2-Channel Universal Wireless Radio Receiver Instruction Manual

1. Úvod

This instruction manual provides detailed guidance for the installation, setup, and operation of your Einaus 2-Channel Universal Wireless Radio Receiver. This device is designed for wireless control of various electrical appliances, including heaters, ventilation systems, air conditioners, pumps, barriers, lighting, multi-channel electric doors and windows, electronic locks, garage doors, lifting equipment, and industrial automation systems. Please read this manual thoroughly before use to ensure proper function and safety.

2. Obsah balení

Po otevření balení byste měli najít následující komponenty:

• 1 x Receiver module with protective casing
• 2 x Remote controls (each with battery installed)

Pokud některé součásti chybí nebo jsou poškozené, kontaktujte prosím zákaznickou podporu.

3. Specifikace

4. Konec produktuview

5. Nastavení a párování

5.1. Vymazání stávajících kódů

To clear all previously paired remote controls from the receiver's memory:

1. Vyhledejte Tlačítko učení on the receiver board.
2. Stiskněte a podržte Tlačítko učení until the indicator light turns off. This indicates that all stored codes have been successfully cleared.

5.2. Pairing a Remote Control (Learning Mode)

To pair a new remote control with the receiver:

1. Stiskněte tlačítko Tlačítko učení on the receiver once. The indicator light will flash once and then turn off. This signifies the receiver is ready to learn a new code in Momentary mode.
2. Immediately press any button on your remote control. The indicator light on the receiver will flash to confirm successful pairing.
3. Repeat for additional remote controls if needed.

6. Provozní režimy

The receiver supports several operating modes, which determine how the relay responds to remote control input. You can set the desired mode by pressing the Tlačítko režimu on the receiver board a specific number of times.

6.1. Okamžitý režim

In Momentary mode, the relay activates only as long as the remote control button is pressed. ReleasinTlačítko deaktivuje relé.

• Nastavení: Stiskněte tlačítko Tlačítko režimu once. The indicator will flash once and turn off.

6.2. Latch Mode

In Latch mode, one button press activates the relay, and another distinct button press is required to deactivate it.

• Nastavení: Stiskněte tlačítko Tlačítko režimu twice. The indicator will flash twice and turn off.

6.3. Přepnout režim

In Toggle mode, a single button press activates the relay, and pressing the same button again deactivates it. It acts like a flip-flop switch.

• Nastavení: Stiskněte tlačítko Tlačítko režimu three times. The indicator will flash three times and turn off.

6.4. 5-Second Delay Mode

This mode activates the relay for a fixed duration of 5 seconds after a button press, then automatically deactivates it.

• Nastavení: Stiskněte tlačítko Tlačítko režimu four times. The indicator will flash four times and turn off.

7. Schémata zapojení

The following diagrams illustrate common wiring configurations for the Einaus 2-Channel Universal Wireless Radio Receiver. Always ensure power is disconnected before making any wiring changes.

8. Údržba

The Einaus Wireless Radio Receiver is designed for reliable operation with minimal maintenance. Follow these guidelines to ensure longevity:

• Čištění: Keep the receiver free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquid cleaners or solvents.
• Prostředí: Ujistěte se, že je přijímač instalován v suchém prostředí, mimo dosah přímé vlhkosti, extrémních teplot a korozivních látek.
• Napájení: Use a stable power supply within the specified voltage rozsah (DC 12-48V).
• Baterie do dálkového ovládání: Replace remote control batteries when their range decreases or they stop responding.

9. Řešení problémů

If you encounter issues with your receiver, refer to the following troubleshooting steps:

• Přijímač neodpovídá:
  • Check the power supply to the receiver. Ensure it is within the 12-48V DC range and properly connected.
  • Zkontrolujte, zda nejsou baterie v dálkovém ovladači vybité.
  • Ensure the remote control is paired correctly. Try re-pairing the remote control (refer to Section 5.2).
  • Check for strong radio interference in the vicinity.
• Krátký provozní dosah:
  • Vyměňte baterie v dálkovém ovladači.
  • Ensure there are no significant obstructions (thick walls, metal structures) between the remote and the receiver.
  • Avoid installing the receiver near large metal objects or other radio-emitting devices.
• Relé se neaktivuje/nedeaktivuje:
  • Check the wiring to the load. Ensure connections are secure and correct according to the wiring diagrams (Section 7).
  • Verify the operating mode is set as intended (Section 6).
  • Ensure the load current does not exceed the maximum 10A rating.

Pokud problém přetrvává i po provedení těchto kroků, kontaktujte prosím zákaznickou podporu.

10. Záruka a podpora

This Einaus product is covered by a standard manufacturer's warranty against defects in materials and workmanship. Please refer to your purchase documentation for specific warranty terms and duration.

Pro technickou podporu, pomoc s řešením problémů nebo reklamaci se prosím obraťte přímo na svého prodejce nebo výrobce. Uschovejte si účtenku jako doklad o koupi.