SIMON Series 10 Double Switch-Commutator Instruction Manual

1. Konec produktuview

The SIMON Series 10 Double Switch-Commutator is designed to control two independent light points from a single location. It can function as a standard ON/OFF switch or as a commutator, redirecting electrical current to connect different circuits. This unit is supplied as a pre-assembled component, including the mechanism, cover, and frame, to simplify the installation process. Its minimalist design with straight lines allows for seamless integration into various interior spaces.

Obrázek 1: Přední strana view of the SIMON Series 10 Double Switch-Commutator.

2. Bezpečnostní upozornění

• Elektrické nebezpečí: Installation should only be performed by a qualified electrician or a person with adequate knowledge of electrical systems. Always disconnect the main power supply before beginning any installation or maintenance work.
• Do not drill into the device or expose it to fire.
• This product is designed for indoor use (IP20 rating). Do not install in environments with high humidity or direct water exposure.
• Ujistěte se, že všechna elektroinstalace jsou bezpečná a splňují místní elektrotechnické předpisy.
• Under no circumstances shall Simon be liable for any indirect, special, incidental, punitive, or consequential damages of any kind arising from improper installation or misuse of the product.

3. Součásti zahrnuty

The SIMON Series 10 Double Switch-Commutator package includes the following components:

• Double Switch-Commutator Mechanism
• Decorative Cover (White)
• Montážní rám

Figure 2: Product as supplied in its packaging.

4. Nastavení a instalace

The SIMON Series 10 Double Switch-Commutator is designed for straightforward installation. The metallic frame provides robustness, while the polypropylene frame offers flexibility during mounting.

4.1. Schéma zapojení a připojení

This device uses screw terminals for secure wiring connections. Refer to the diagram below for proper wiring. If you are unfamiliar with electrical wiring, consult a professional electrician.

Obrázek 3: Rozložené view showing the mechanism, frame, and cover assembly.

1. Příprava: Ensure the main power supply to the circuit is turned OFF at the consumer unit/fuse box.
2. Mounting the Mechanism: Place the switch mechanism into the wall box. The flexible polypropylene frame aids in positioning.
3. Zapojení: Connect the electrical wires to the screw terminals. For a double switch-commutator, typically you will have a common phase wire (L) and two switched phase wires (L1, L2) for each light point, along with neutral and earth connections if applicable to the installation type. Ensure all connections are tight.
4. Zabezpečení: Use the metallic claws to firmly secure the mechanism to the wall box.
5. Attaching the Cover and Frame: Snap the decorative cover and frame onto the mechanism until they are securely in place.
6. Závěrečná kontrola: Once installation is complete, restore power and test the functionality of both switches.

5. Návod k obsluze

The SIMON Series 10 Double Switch-Commutator features two independent rocker switches. Each switch can control a separate light point or circuit.

• Funkce spínače: Press the top part of the rocker to turn the connected light/circuit ON. Press the bottom part to turn it OFF.
• Commutator Function: When configured as a commutator, pressing the rocker will switch the current path between two different conductors, allowing control of a light from multiple locations (e.g., at the top and bottom of a staircase).

6. Údržba

The SIMON Series 10 Double Switch-Commutator requires minimal maintenance.

• Čištění: To clean the surface, gently wipe with a soft, dry cloth. For stubborn marks, use a slightly damp hadříkem s jemným mýdlem a poté ihned osušte.
• Vyhněte se: Nepoužívejte abrazivní čisticí prostředky, rozpouštědla ani agresivní chemikálie, protože by mohly poškodit povrchovou úpravu.
• Inspekce: Periodically check for any loose connections or signs of wear. If any damage is observed, disconnect power and replace the unit.

7. Řešení problémů

If the switch-commutator is not functioning as expected, consider the following:

• Bez napájení: Check the main power supply and the circuit breaker. Ensure power is restored to the circuit.
• Světlo se nezapíná/nevypíná: Verify that the light bulb is functional. Check all wiring connections at the switch and the light fixture for looseness or incorrect wiring.
• Přerušovaný provoz: This could indicate a loose connection. Disconnect power and re-check all screw terminals.
• Difficulty in Wiring: The wiring diagram on the mechanism can be complex for some users. If you encounter difficulties, it is recommended to consult a qualified electrician.

8. Specifikace

9. Záruka a podpora

For warranty information or technical support, please contact Simon customer service. Keep your purchase receipt as proof of purchase.

Visit the official Simon website for additional resources, FAQs, or to locate authorized service centers.