Návod k obsluze nástěnného držáku na televizi BONTEC

Zavedení

This manual provides detailed instructions for the safe and proper installation, operation, and maintenance of your BONTEC TV Wall Mount, Model CT139S. This full-motion articulated arm mount is designed to securely hold 32-70 inch flat or curved LCD/LED/OLED TVs with a maximum load capacity of 132 lbs (60 kg). It supports VESA patterns from 200x100mm up to 400x400mm.

Key features include an extra-long arm extending up to 33.5 inches, offering flexible viewing positions, and the ability to retract to just 2.56 inches from the wall for space-saving. The mount also provides ±90° swivel, ±8° tilt, and ±3° level adjustment for optimal viewing comfort. Constructed from premium cold-rolled steel, it ensures durability and safety.

Figure 1: Complete BONTEC TV Wall Mount components.

Bezpečnostní informace

VAROVÁNÍ: Read all instructions carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, consult a qualified installer. Improper installation may cause serious injury or damage.

• This product is intended for installation on wood studs, solid concrete, or brick walls. NEMONTUJTE POUZE NA SÁDROKARON.
• Ensure the mounting surface can safely support the combined weight of the mount and the display. The maximum load capacity for this mount is 132 lb (60 kg).
• Use only the hardware provided by the manufacturer. Using incompatible hardware may cause damage or injury.
• Pro přesné nalezení dřevěných trámů vždy používejte detektor trámů.
• For concrete or brick walls, ensure proper anchors are used and drilled holes are of the correct size.
• Installation often requires two people for safety and ease.

Figure 2: Diverse wall compatibility for the mount. Always ensure proper wall type and secure fastening.

Obsah balení

Před zahájením instalace ověřte, zda jsou všechny součásti přítomny a nepoškozené. Pokud některé součásti chybí nebo jsou vadné, kontaktujte zákaznický servis společnosti BONTEC.

Pokyny pro nastavení

Krok 1: Montáž nástěnné desky

Determine your wall type (wood stud, concrete, or brick) and follow the appropriate instructions. Use the provided template to mark drill holes accurately. A magnetic spirit level is included to ensure precise alignment.

Pro dřevěné stěny s nosníky:

1. Use a stud finder to locate the edges and center of the wood studs. Mark the center of the studs where you intend to mount the wall plate.
2. Place the wall plate against the wall, aligning the mounting holes with the marked stud centers. Use the integrated spirit level to ensure it is perfectly horizontal.
3. Označte si body pro vrtání skrz otvory ve nástěnné desce.
4. Drill pilot holes into the wood studs using a 5.5mm (7/32 inch) drill bit to a depth of 60mm (2.36 inches).
5. Attach the wall plate to the wall using the Self-tap Screws (ST6.3*55mm) and Washers (φ6mm). Tighten securely with the wrench.

For Concrete or Brick Walls:

1. Place the wall plate against the wall at the desired height. Use the integrated spirit level to ensure it is perfectly horizontal.
2. Označte si body pro vrtání skrz otvory ve nástěnné desce.
3. Drill holes into the concrete or brick using a 10mm (3/8 inch) masonry drill bit to a depth of 60mm (2.36 inches).
4. Insert the Concrete Anchors (D6*50mm) into the drilled holes. Ensure they are flush with the wall surface.
5. Attach the wall plate to the wall using the Self-tap Screws (ST6.3*55mm) and Washers (φ6mm) into the anchors. Tighten securely with the wrench.

Step 2: Attaching the TV Brackets to Your TV

Select the appropriate screws (M4, M6, or M8) and spacers that fit your TV's VESA mounting holes. The VESA pattern for this mount ranges from 200x100mm to 400x400mm.

1. Opatrně položte televizor displejem dolů na měkký, čistý povrch, abyste zabránili poškrábání.
2. Align the TV brackets with the VESA mounting holes on the back of your TV. Ensure the brackets are oriented correctly (usually with the longer arms pointing downwards).
3. Insert the chosen screws through the washers (if needed), then through the TV brackets, and into the TV's mounting holes. If your TV has an uneven back or recessed holes, use the appropriate spacers to ensure a flat and secure fit.
4. Všechny šrouby pevně utáhněte, ale nepřetahujte je.

Step 3: Hanging TV to the Brackets and Locking It

This step typically requires two people due to the weight and size of the TV.

1. Carefully lift the TV with the attached brackets and hook the brackets onto the wall plate's arms. Ensure both brackets are securely seated on the arms.
2. Once the TV is hung, locate the locking screws or mechanisms on the bottom of the TV brackets. Tighten these screws to secure the TV to the wall plate, preventing accidental dislodgement.

Návod k obsluze

The BONTEC TV Wall Mount offers full motion capabilities for an optimal viewzkušenosti.

Nastavení pozice TV:

• Prodloužení/zatažení: Gently pull the TV away from the wall to extend the arm up to 33.5 inches, or push it back to retract it to 2.56 inches.
• Otočný: The mount allows for ±90° swivel (180° total left to right movement) depending on TV size and wall clearance. Carefully pivot the TV to your desired viewúhel.
• Náklon: The TV can be tilted ±8° to reduce glare or achieve a better viewing angle. Loosen the tilt adjustment knobs on the TV brackets, adjust the angle, and then re-tighten to secure.
• Úprava úrovně: If the TV appears unlevel after installation, you can adjust it by ±3°. This adjustment is typically done by loosening specific screws on the TV plate and rotating the TV slightly, then re-tightening. Refer to the detailed diagram in the installation video for precise adjustment points.

Figure 3: Extension range of the articulated arm.

Figure 4: Swivel range for flexible viewing úhly.

Figure 5: Tilt and level adjustment for optimal viewIng.

Správa kabelů:

Use the included cable ties to neatly route and secure your TV cables along the articulated arm. This helps maintain a clean appearance and prevents cables from being pinched or damaged during adjustments.

Údržba

Pravidelná údržba zajistí dlouhou životnost a bezpečný provoz vašeho nástěnného držáku televizoru.

• Pravidelná prohlídka: Every 6-12 months, check all screws and connections to ensure they remain tight and secure. Re-tighten any loose fasteners.
• Čištění: Otřete držák měkkým, suchým hadříkem, abyste odstranili prach. V případě odolných skvrn jemněamp Lze použít hadřík a poté jej osušit. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla.
• Mazání: The articulated joints are designed for smooth movement. If you notice any stiffness over time, a small amount of silicone-based lubricant can be applied to the pivot points.
• Kontrola hmotnosti: Do not exceed the maximum weight capacity of 132 lbs (60 kg). If you replace your TV, ensure its weight and VESA pattern are within the mount's specifications.

Odstraňování problémů

Zde jsou některé běžné problémy a jejich možná řešení:

• TV appears unlevel: Use the ±3° level adjustment feature. Loosen the relevant screws on the TV plate, adjust the TV, and re-tighten. Ensure the wall plate itself was installed level using the spirit level.
• Mount feels unstable or wobbly: Immediately remove the TV from the mount. Re-check all wall mounting screws and TV bracket screws to ensure they are securely tightened. Verify that the mount is installed into appropriate wall structures (wood studs, concrete, or brick) and not just drywall.
• Difficulty extending or swiveling the arm: Check for any obstructions. Ensure cables are not caught in the joints. Apply a small amount of silicone-based lubricant to the pivot points if movement is stiff.
• TV not fitting the VESA pattern: Double-check your TV's VESA dimensions against the mount's compatibility (200x100mm to 400x400mm). Ensure you are using the correct screws and spacers for your TV model.

If you encounter issues not listed here or require further assistance, please contact BONTEC customer support.

Specifikace

Informace o záruce

BONTEC products typically come with a manufacturer's warranty. For specific warranty terms and conditions, including duration and coverage, please refer to the warranty card included with your product or visit the official BONTEC webUschovejte si účtenku jako doklad o koupi pro případné reklamace.

Podpora

For technical support, missing parts, or any questions regarding your BONTEC TV Wall Mount, please contact BONTEC customer service. You can often find contact information on the product packaging, the official BONTEC webwebu nebo prostřednictvím prodejce, u kterého jste produkt zakoupili.

Visit the official BONTEC store for more information and products: Obchod BONTEC na Amazonu