1. Konec produktuview
The IBO S-150 is an electronic control unit designed for managing the circulation pump in a central heating system. Its primary function is to activate the pump when the water temperature exceeds a preset value and deactivate it when the temperature falls below that value. This intelligent control helps to optimize energy consumption and extend the operational lifespan of the pump.
Klíčové vlastnosti:
- Integrated Thermostat Function: Allows setting specific temperature thresholds for pump activation and deactivation.
- Funkce proti zamrznutí: Automatically activates the pump if the ambient temperature drops below 5 °C (41 °F) to prevent freezing within the system.
- Úspora energie: Prevents unnecessary pump operation, leading to reduced energy consumption.
- Extended Pump Lifespan: Reduces wear and tear on the pump by operating it only when required.
- LED indikátory: Two LED displays show current temperature and set stop temperature.
- Uživatelsky přívětivé rozhraní: Simple button controls for setting parameters.
2. Bezpečnostní informace
Před instalací a provozem si pečlivě přečtěte všechny bezpečnostní pokyny. Nedodržení těchto pokynů může vést k úrazu elektrickým proudem, požáru nebo vážnému zranění.
- Elektrická bezpečnost: Installation and maintenance should only be performed by qualified personnel in accordance with local electrical codes and regulations.
- Odpojení napájení: Always disconnect the power supply to the central heating system and the controller before performing any installation, wiring, or maintenance.
- Voda a vlhkost: Do not expose the controller to water, excessive moisture, or extreme temperatures. Ensure the installation location is dry and protected.
- Správné uzemnění: Ensure the device is properly grounded to prevent electrical hazards.
- Integrita kabelu: Regularly inspect all cables for damage. Do not use the device if any cables are frayed or damaged.
- Zamýšlené použití: Use the controller only for its intended purpose as a central heating pump controller.
3. Technické specifikace
| Parametr | Hodnota |
|---|---|
| Temperature Setting Range (Set Temperature) | 0 °C až 99 °C (32 °F až 210 °F) |
| Temperature Setting Range (Stop Temperature) | 0 °C až 99 °C (32 °F až 210 °F) |
| Okolní teplota | -10 °C až 40 °C (14 °F až 104 °F) |
| Typ snímače teploty | Ohmic |
| Napájecí zdroj Voltage | 230 V, 50 Hz, ±10% |
| Power Consumption (Controller Only) | <5 W |
| Délka kabelu senzoru | Přibližně 1 m (3.3 stop) |
| Délka napájecího kabelu | Přibližně 1 m (3.3 stop) |
| Pump Power Cable Length | Přibližně 1 m (3.3 stop) |
| Výstup | 230 V / 50 Hz |
| Maximum Load (Pump) | 6 A (Resistive Load) |
| Přesnost měření | ~0.1 °C |
| Rozměry produktu (D x Š x V) | 14 x 14 x 5 cm (5.5 x 5.5 x 2 palce) |
| Hmotnost | 370 gramů (0.82 lb) |
4. Instalace a nastavení
Before proceeding with installation, ensure the main power supply to your central heating system is turned off at the circuit breaker.
4.1. Montáž regulátoru
Select a suitable, dry location for mounting the controller, away from direct heat sources or excessive moisture. The controller can be mounted on a wall using appropriate fasteners (not included). Ensure sufficient space for cable connections.
4.2. Připojení kabelů
The IBO S-150 controller comes with three main connections:
- Napájecí kabel: This cable supplies power to the controller. Plug it into a standard 230V, 50Hz electrical outlet.
- Pump Power Cable: This cable connects the controller to your central heating circulation pump. Ensure the pump is compatible with the controller's specifications (Max load: 6A).
- Temperature Sensor Cable: The ohmic temperature sensor should be placed in a location where it can accurately measure the water temperature of the central heating system. Typically, this is on the return pipe or a designated sensor pocket. Ensure good thermal contact for accurate readings.
Obrázek 1: Přesview of the IBO S-150 controller with its connected power, pump, and sensor cables.
Obrázek 2: Spodní část view of the controller, illustrating the connection points for the power and pump cables.
After all connections are securely made, restore power to the central heating system.
5. Provoz
The IBO S-150 controller features a simple interface with two LED displays and three control buttons.
Figure 3: Front panel of the IBO S-150 controller, showing the LED displays and control buttons.
5.1. Počáteční zapnutí
Upon initial power-on, the upper LED display will show the current temperature measured by the sensor. The lower LED display will show the currently set 'stop temperature'.
5.2. Ovládací tlačítka
- Tlačítko MENU: Used to cycle through and select different settings (stop temperature, start temperature, anti-freeze function). Pressing this button allows you to enter the setting mode for each parameter.
- UP Arrow Button (▲): Used to increase the value of a selected parameter.
- DOWN Arrow Button (▼): Used to decrease the value of a selected parameter.
5.3. Nastavení teplotních parametrů
- Stiskněte tlačítko MENU button to enter the setting mode. The lower display will start flashing, indicating you can adjust the 'stop temperature'.
- Použijte NAHORU (▲) a DOLŮ (▼) arrow buttons to set the desired temperature at which the pump should stop.
- Stiskněte tlačítko MENU button again to confirm the 'stop temperature' and move to the 'start temperature' setting. The lower display will flash again.
- Použijte NAHORU (▲) a DOLŮ (▼) arrow buttons to set the desired temperature at which the pump should start. This is typically a few degrees higher than the stop temperature to prevent rapid cycling.
- Stiskněte tlačítko MENU button a third time to confirm the 'start temperature' and exit the setting mode. The controller will return to displaying the current and stop temperatures.
5.4. Funkce proti zamrznutí
The anti-freeze function is automatically engaged. If the temperature measured by the sensor drops below 5 °C (41 °F), the pump will activate regardless of other settings to circulate water and prevent freezing. This function cannot be manually disabled.
6. Údržba
The IBO S-150 controller requires minimal maintenance to ensure optimal performance and longevity.
- Čištění: Periodically wipe the exterior of the controller with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.
- Kontrola kabelů: Regularly check all connected cables (power, pump, sensor) for any signs of wear, damage, or loose connections. Replace damaged cables immediately.
- Umístění senzoru: Ensure the temperature sensor remains securely in its intended position and maintains good thermal contact with the heating system pipe.
- Podmínky prostředí: Verify that the controller's operating environment remains within the specified ambient temperature and humidity ranges.
7. Řešení problémů
If you encounter issues with your IBO S-150 controller, refer to the following troubleshooting guide:
| Problém | Možná příčina | Řešení |
|---|---|---|
| Ovladač se nezapne. | No power supply; loose power cable; faulty outlet. | Check power outlet; ensure power cable is securely plugged in; check circuit breaker. |
| Pump does not turn on when temperature is high. | Incorrect 'start temperature' setting; faulty pump connection; pump malfunction. | Verify 'start temperature' setting; check pump power cable connection; test pump independently if possible. |
| Pump does not turn off when temperature is low. | Incorrect 'stop temperature' setting; sensor malfunction. | Verify 'stop temperature' setting; check sensor connection and placement. |
| Odečet teploty je nepřesný. | Sensor improperly placed; faulty sensor. | Ensure sensor has good thermal contact and is correctly positioned; replace sensor if necessary. |
| Anti-freeze function activates unexpectedly. | Ambient temperature near or below 5 °C; sensor reading error. | This is normal operation if ambient temperature is low. Check sensor reading for accuracy. |
If the problem persists after attempting these solutions, please contact a qualified technician or the product support.
8. Záruka a podpora
Informace o záruce a technickou podporu naleznete v dokumentaci dodané s vaším nákupem nebo se obraťte na svého prodejce. Uschovejte si doklad o koupi pro případné reklamace.
Manufacturer: IBO
Číslo modelu: S-150