U.S. Solid 3/4" Brass Electric Solenoid Valve

1. Konec produktuview

The U.S. Solid 3/4" Brass Electric Solenoid Valve is a high-quality, normally closed valve designed for various industrial applications. Its robust brass construction and VITON seal ensure durability and compatibility with a range of fluids including non-potable water, air, diesel, gasoline, kerosene oil, and natural gas.

This valve is engineered for rapid response, opening or closing in less than 1 second. It is important to note that this valve is not designed for continuous duty; prolonged use exceeding 8 hours in a single cycle may shorten its lifespan and cause damage.

Obrázek 1.1: Přední strana view of the U.S. Solid 3/4" Brass Electric Solenoid Valve.

2. Bezpečnostní informace

UPOZORNĚNÍ: Tento výrobek vás může vystavit chemikáliím včetně olova, které je ve státě Kalifornie známo, že způsobuje rakovinu a vrozené vady nebo jiné poškození reprodukce. Pro více informací přejděte na www.P65Warnings.ca.gov.

Figure 2.1: California Proposition 65 Warning and IP65 Ingress Protection rating details.

Always ensure proper electrical grounding when installing and operating the valve. Refer to local electrical codes and standards.

Figure 2.2: Ensure proper electrical grounding for safe operation.

3. Vlastnosti produktu

• Industrial Grade Brass Construction: Corrosion-resistant and suitable for higher temperature applications.
• VITON Seal: Provides superior durability and resistance to high temperatures and corrosive chemicals, including gasoline, diesel fuel, oils, and lubricants.
• Fast Actuation: Opens and closes in less than 1 second for instantaneous flow control.
• Dlouhá životnost: Engineered for over a million cycles under proper operating conditions.
• Normálně zavřeno: The valve remains closed when de-energized and opens when energized.
• Krytí IP65: Protected against dust ingress and low-pressure water jets from any direction.

Obrázek 3.1: Strana view showing the electrical wiring connection.

4. Specifikace

Figure 4.1: Key dimensions and weight of the solenoid valve.

5. Nastavení a instalace

1. Příprava: Ensure the power supply is disconnected before beginning installation. Verify that the fluid type is compatible with brass and VITON seals. This valve is not suitable for drinking water applications.
2. Těsnění závitu: Apply appropriate thread sealant (e.g., PTFE tape) to the pipe threads before connecting the valve to prevent leaks.

Figure 5.1: Proper application of thread sealant is crucial for leak-free connections.
3. Směr toku: Observe the flow arrow indicated on the valve body to ensure correct installation direction.


Figure 5.2: The flow arrow on the valve body indicates the correct fluid direction.

4. Montáž: Mount the valve securely in a position that allows for easy access for wiring and maintenance.
5. Elektrické připojení: Connect the valve to a 110V AC power source. Ensure all electrical connections are secure and properly insulated. Refer to Figure 3.1 for wiring reference.

6. Provoz

This is a normally closed solenoid valve. When electrical power (110V AC) is supplied to the coil, the valve will energize and open, allowing fluid to flow. When the power is removed, the valve will de-energize and close, stopping the fluid flow.

The valve is designed for quick actuation, opening or closing almost instantaneously. Avoid continuous operation for more than 8 hours in a single cycle to prevent overheating and potential damage to the coil.

Figure 6.1: Thermal image illustrating heat generated during valve operation. Prolonged operation can lead to excessive heat.

7. Údržba

• Pravidelná kontrola: Periodically inspect the valve for any signs of leaks, corrosion, or damage to the wiring.
• Čištění: Keep the exterior of the valve clean and free from debris. Do not use harsh chemicals that may damage the brass or rubber components.
• Coil Check: Ensure the coil is not excessively hot during operation. If it is, reduce the operating time or check for proper voltage zásobování.
• Výměna těsnění: If leaks occur around the valve body, the internal VITON seal may need replacement. Consult a qualified technician for internal component servicing.

Obrázek 7.1: Rozložené view showing the main components of the solenoid valve for reference during maintenance.

8. Řešení problémů

9. Záruka a podpora

All U.S. Solid products, including this solenoid valve, come with a JEDEN ROK ZÁRUKA from the date of purchase. If the valve becomes defective within this period due to manufacturing defects, U.S. Solid will gladly replace it.

For technical support, warranty claims, or further assistance, please contact U.S. Solid customer service through their official webna webu nebo u prodejce, kde byl produkt zakoupen.

Uschovejte si prosím doklad o koupi pro ověření záruky.