Andoer AC-04 Wireless Trigger System

1. Úvod

This manual provides detailed instructions for the safe and effective use of your Andoer AC-04 Wireless Trigger System. This system is designed to wirelessly trigger studio flash lights, enhancing flexibility and efficiency in photographic setups. Please read this manual thoroughly before operating the device and retain it for future reference.

2. Bezpečnostní informace

To prevent damage to the product or injury to yourself or others, observe the following safety precautions:

• Nevystavujte zařízení vodě ani nadměrné vlhkosti.
• Zabraňte pádu zařízení nebo jeho vystavení silným nárazům.
• Nepokoušejte se zařízení rozebírat ani upravovat. Opravy by měl provádět pouze autorizovaný servisní personál.
• Udržujte zařízení mimo dosah silných magnetických polí.
• Používejte pouze určené zdroje napájení a příslušenství.
• Během používání zajistěte dostatečné větrání, aby nedošlo k přehřátí.

3. Obsah balení

Ověřte, zda jsou v balení obsaženy všechny níže uvedené položky:

• 1 x Bezdrátová vysílací jednotka
• 1 x Wireless Receiver Unit (AC-04)
• 1 x adaptér z 3.5 mm na 6.35 mm

Obrázek 3.1: All components of the Andoer AC-04 Wireless Trigger System, including the transmitter, receiver, and the 3.5mm to 6.35mm adapter.

4. Konec produktuview

The Andoer AC-04 Wireless Trigger System consists of a transmitter and a receiver, designed for reliable wireless control of studio flash units. It features 4 selectable channels to avoid interference.

4.1. Transmitter Unit

The transmitter unit mounts onto your camera's hot shoe. It sends the trigger signal to the receiver when the camera's shutter is released.

Obrázek 4.1: The transmitter unit (top left) with its cold shoe mount and the receiver unit (bottom right) labeled AC-04.

4.2. Receiver Unit (AC-04)

The receiver unit connects to your studio flash light. It receives the signal from the transmitter and triggers the flash. It features a power input and a sync port.

Obrázek 4.2: The AC-04 receiver unit connected to its power cable and sync cable, alongside the transmitter and adapter.

4.3. 3.5mm to 6.35mm Adapter

This adapter ensures compatibility with various studio flash units that may have either a 3.5mm or 6.35mm sync port.

Obrázek 4.3: Detailní view of the 3.5mm jack, the 6.35mm adapter, and the power input/output connectors.

5. Nastavení

Follow these steps to set up your wireless trigger system:

1. Install Batteries (if applicable): The product description does not specify battery requirements. If your units require batteries, insert them according to the polarity markings.
2. Mount the Transmitter: Slide the transmitter unit onto your camera's hot shoe. Ensure it is securely fastened.
3. Connect the Receiver to Flash:
   • Connect the power cable of the receiver unit to a suitable power outlet.
   • Identify the sync port on your studio flash light.
   • Connect the sync cable from the receiver to the flash unit. If your flash unit has a 6.35mm port, use the provided 3.5mm to 6.35mm adapter.
4. Vyberte kanály: Both the transmitter and receiver units have channel selectors (typically switches labeled 1-4). Set both units to the same channel to ensure proper communication. For example, if the transmitter is set to channel 1, the receiver must also be set to channel 1.

6. Návod k obsluze

Once setup is complete, operate the system as follows:

1. Zapnutí: Ensure both your camera and studio flash unit are powered on. The receiver unit should also be powered on (if it has a separate power switch).
2. Spouštěč testu: Most transmitters have a test button. Press this button to manually trigger the flash and confirm the connection. The flash should fire.
3. Fotit: With the system properly configured and tested, you can now take photos. When your camera's shutter is released, the transmitter will send a signal to the receiver, triggering the studio flash.
4. Změna kanálů (pokud je to nutné): If you experience interference from other wireless devices, change the channel on both the transmitter and receiver to a different matching channel (e.g., from 1 to 2).

7. Údržba

Proper care and maintenance will extend the life of your wireless trigger system:

• Čištění: K čištění vnější strany jednotek používejte měkký, suchý hadřík. Nepoužívejte tekuté čisticí prostředky ani rozpouštědla.
• Skladování: When not in use, store the units in a cool, dry place, away from direct sunlight and extreme temperatures.
• Výměna baterie: If the units use batteries, replace them when performance degrades or if the units will be stored for an extended period to prevent leakage.
• Kontrola kabelů: Regularly inspect all cables for signs of wear or damage. Replace damaged cables immediately.

8. Řešení problémů

9. Specifikace

10. Záruka a podpora

Andoer products are manufactured to high quality standards. For information regarding warranty coverage, technical support, or service, please refer to the warranty card included with your product or visit the official Andoer webstránky. Uschovejte si prosím doklad o koupi pro případ reklamace.